ISO 10300-2:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Calculation of load capacity of bevel gears — Part 2: Calculation of surface durability (pitting)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
24-08-2023
English
17-03-2014
Important note : Users cannot be edited or removed once added to your Multi user PDF.
ISO 10300-2:2014 specifies the basic formulae for use in the determination of the surface load capacity of straight and helical (skew), Zerol and spiral bevel gears including hypoid gears, and comprises all the influences on surface durability for which quantitative assessments can be made. ISO 10300-2:2014 is applicable to oil lubricated bevel gears, as long as sufficient lubricant is present in the mesh at all times.
The formulae in ISO 10300-2:2014 are based on virtual cylindrical gears and restricted to bevel gears whose virtual cylindrical gears have transverse contact ratios of Ɛvα < 2. The results are valid within the range of the applied factors as specified in ISO 10300-1 (see ISO 6336-2). Additionally, the given relations are valid for bevel gears of which the sum of profile shift coefficients of pinion and wheel is zero (see ISO 23509).
| Committee |
ISO/TC 60/SC 2
|
| DevelopmentNote |
Supersedes ISO/DIS 10300-2. (03/2014)
|
| DocumentType |
Standard
|
| Pages |
30
|
| ProductNote |
THIS STANDARD IS ALSO REFERES TO ANSI/AGMA 2003-C10
|
| PublisherName |
International Organization for Standardization
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| DS ISO 10300-2 : 2014 | Identical |
| NEN ISO 10300-2 : 2014 | Identical |
| BS ISO 10300-2:2014 | Identical |
| SAC GB/T 10062.2 : 2003 | Identical |
| ISO/TR 10300-30:2017 | Calculation of load capacity of bevel gears — Part 30: ISO rating system for bevel and hypoid gears — Sample calculations |
| ISO/TS 6336-20:2017 | Calculation of load capacity of spur and helical gears Part 20: Calculation of scuffing load capacity (also applicable to bevel and hypoid gears) Flash temperature method |
| PD ISO/TR 22849:2011 | Design recommendations for bevel gears |
| BS EN 13135 : 2013 | CRANES - SAFETY - DESIGN - REQUIREMENTS FOR EQUIPMENT |
| EN 13135:2013+A1:2018 | Cranes - Safety - Design - Requirements for equipment |
| ISO 10300-3:2014 | Calculation of load capacity of bevel gears — Part 3: Calculation of tooth root strength |
| I.S. EN 13135:2013 | CRANES - SAFETY - DESIGN - REQUIREMENTS FOR EQUIPMENT |
| 11/30235014 DC : 0 | BS EN 13135 - CRANES - SAFETY - DESIGN - REQUIREMENTS FOR EQUIPMENT |
| AGMA ISO 23509 : A | BEVEL AND HYPOID GEAR GEOMETRY |
| 11/30229142 DC : 0 | BS ISO 10300-3 - CALCULATION OF LOAD CAPACITY OF BEVEL GEARS - PART 3: CALCULATION OF TOOTH ROOT STRENGTH |
| BS ISO/TR 13989-1:2000 | Calculation of scuffing load capacity of cylindrical, bevel and hypoid gears Flash temperature method |
| BS ISO 10300-3:2014 | Calculation of load capacity of bevel gears Calculation of tooth root strength |
| BS ISO 10300-1:2014 | Calculation of load capacity of bevel gears Introduction and general influence factors |
| ISO/TR 22849:2011 | Design recommendations for bevel gears |
| UNE-EN 13135:2013 | Cranes - Safety - Design - Requirements for equipment |
| ISO 10300-1:2014 | Calculation of load capacity of bevel gears — Part 1: Introduction and general influence factors |
| 05/30110655 DC : DRAFT JAN 2005 | ISO 23509 - BEVEL AND HYPOID GEAR GEOMETRY |
| 11/30229148 DC : 0 | BS ISO 10300-1 - CALCULATION OF LOAD CAPACITY OF BEVEL GEARS - PART 1: INTRODUCTION AND GENERAL INFLUENCE FACTORS |
| DIN EN 13135:2013-05 | CRANES - SAFETY - DESIGN - REQUIREMENTS FOR EQUIPMENT |
| 15/30298301 DC : 0 | BS ISO 23509 - BEVEL AND HYPOID GEAR GEOMETRY |
| PD ISO/TR 10300-30:2017 | Calculation of load capacity of bevel gears ISO rating system for bevel and hypoid gears. Sample calculations |
| AGMA 932 : A | RATING THE PITTING RESISTANCE AND BENDING STRENGTH OF HYPOID GEARS |
| ISO 6336-2:2006 | Calculation of load capacity of spur and helical gears Part 2: Calculation of surface durability (pitting) |
| AGMA 2003 : B | RATING THE PITTING RESISTANCE AND BENDING STRENGTH OF GENERATED STRAIGHT BEVEL, ZEROL BEVEL AND SPIRAL BEVEL GEAR TEETH |
| ISO/TR 10064-6:2009 | Code of inspection practice Part 6: Bevel gear measurement methods |
| ISO 6336-5:2016 | Calculation of load capacity of spur and helical gears Part 5: Strength and quality of materials |
| ISO 10300-1:2014 | Calculation of load capacity of bevel gears — Part 1: Introduction and general influence factors |
| ISO/TR 22849:2011 | Design recommendations for bevel gears |
| ISO 23509:2016 | Bevel and hypoid gear geometry |
| ISO 10300-3:2014 | Calculation of load capacity of bevel gears — Part 3: Calculation of tooth root strength |
| ISO 6336-6:2006 | Calculation of load capacity of spur and helical gears Part 6: Calculation of service life under variable load |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.