ISO 16063-15:2006
Current
The latest, up-to-date edition.
Methods for the calibration of vibration and shock transducers Part 15: Primary angular vibration calibration by laser interferometry
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
English
21-07-2006
Important note : Users cannot be edited or removed once added to your Multi user PDF.
ISO 16063-15:2006 specifies the instrumentation and procedures used for primary angular vibration calibration of angular transducers, i.e. angular accelerometers, angular velocity transducers and rotational angle transducers (with or without amplifier) to obtain the magnitude and the phase shift of the complex sensitivity by steady-state sinusoidal vibration and laser interferometry. The methods specified in ISO 16063-15:2006 are applicable to measuring instruments (rotational laser vibrometers in particular) and to angular transducers as defined in ISO 2041 for the quantities of rotational angle, angular velocity and angular acceleration.
ISO 16063-15:2006 is applicable to a frequency range from 1 Hz to 1,6 kHz and a dynamic range (amplitude) from 0,1 rad/s2 to 1 000 rad/s2 (frequency-dependent). Calibration frequencies lower than 1 Hz (e.g. 0,4 Hz, which is a reference frequency used in other International Standards) and angular acceleration amplitudes smaller than 0,1 rad/s2 can be achieved using method 3A or method 3B specified in ISO 16063-15:2006, in conjunction with an appropriate low-frequency angular vibration generator.
ISO 16063-15:2006 describes six methods. Method 1A ( fringe-counting, interferometer type A) and method 1B ( fringe-counting, interferometer type B) are applicable to the calibration of the magnitude of complex sensitivity in the frequency range of 1 Hz to 800 Hz and under special conditions, at higher frequencies. Method 2A (minimum-point method, interferometer type A) and method 2B (minimum-point method, interferometer type B) can be used for sensitivity magnitude calibration in the frequency range of 800 Hz to 1,6 kHz. Method 3A (sine-approximation method, interferometer type A) and method 3B (sine-approximation method, interferometer type B) can be used for magnitude of sensitivity and phase calibration in the frequency range of 1 Hz to 1,6 kHz. Methods 1A, 1B and 3A, 3B provide for calibrations at fixed angular acceleration amplitudes at various frequencies. Methods 2A and 2B require calibrations at fixed rotational angle amplitudes (angular velocity amplitude and angular acceleration amplitude vary with frequency).
| DevelopmentNote |
Supersedes ISO/DIS 16063-15 (07/2006)
|
| DocumentType |
Standard
|
| Pages |
42
|
| PublisherName |
International Organization for Standardization
|
| Status |
Current
|
| Standards | Relationship |
| GOST R ISO 16063-15 : 2012 | Identical |
| NEN ISO 16063-15 : 2006 | Identical |
| BS ISO 16063-15:2006 | Identical |
| DKD-R 3-1-1 : 2010 | KALIBRIERUNG VON BESCHLEUNIGUNGSMESSGERAETEN NACH DEM VERGLEICHSVERFAHREN - BLATT 1: GRUNDLAGEN |
| EN 62047-20:2014 | Semiconductor devices - Micro-electromechanical devices - Part 20: Gyroscopes |
| 12/30256751 DC : 0 | BS EN 62047-20 - SEMICONDUCTOR DEVICES - MICRO-ELECTROMECHANICAL DEVICES - PART 20: GYROSCOPES |
| I.S. EN 62047-20:2014 | SEMICONDUCTOR DEVICES - MICROELECTROMECHANICAL DEVICES - PART 20: GYROSCOPES |
| DKD-R 3-1-3 : 2003 | KALIBRIERUNG VON BESCHLEUNIGUNGSMESSGERAETEN NACH DEM VERGLEICHSVERFAHREN - TEIL 3: SINUS- UND MULTISINUS-ANREGUNG |
| IEC 62047-20:2014 | Semiconductor devices - Micro-electromechanical devices - Part 20: Gyroscopes |
| DKD-R 3-1-4 : 2005 | KALIBRIERUNG VON BESCHLEUNIGUNGSMESSGERAETEN NACH DEM VERGLEICHSVERFAHREN - BLATT 4: PRIMAERKALIBRIERUNG VON SCHWINGUNGSMESSGERAE-TEN MIT SINUSFOERMIGER ANREGUNG UND INTERFEROMETRISCHER MESSUNG DER SCHWIN-GUNGSGROESSE |
| BS ISO 21289:2008 | Mechanical vibration and shock. Parameters to be specified for the acquisition of vibration data |
| BS EN 62047-20:2014 | Semiconductor devices. Micro-electromechanical devices Gyroscopes |
| ISO 21289:2008 | Mechanical vibration and shock — Parameters to be specified for the acquisition of vibration data |
| DKD-R 3-1-2 : 2010 | KALIBRIERUNG VON BESCHLEUNIGUNGSMESSGERAETEN NACH DEM VERGLEICHSVERFAHREN - BLATT 2: STOSSANREGUNG |
| ISO 266:1997 | Acoustics — Preferred frequencies |
| ISO 2041:2009 | Mechanical vibration, shock and condition monitoring Vocabulary |
| ISO 16063-1:1998 | Methods for the calibration of vibration and shock transducers Part 1: Basic concepts |
| ISO 16063-11:1999 | Methods for the calibration of vibration and shock transducers Part 11: Primary vibration calibration by laser interferometry |
| ISO 5348:1998 | Mechanical vibration and shock Mechanical mounting of accelerometers |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.