Skip to content
Please enter a keyword to search

  • ISO 16611:2017

    Current The latest, up-to-date edition.

    Plastics piping systems for drainage and sewerage without pressure — Non-circular pipes and joints made of glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resins (UP) — Dimensions, requirements and tests

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Language(s):  English

    Published date:  15-06-2017

    Publisher:  International Organization for Standardization

    Add To Cart

    Abstract - (Show below) - (Hide below)

    ISO 16611:2017 specifies the required properties of the piping system and its components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) intended to be used for drainage or sewerage without pressure including culverts.

    It is the responsibility of the purchaser or specifier to make the appropriate selections taking into account their particular requirements and any relevant national regulations and installation practices or codes.

    ISO 16611:2017 is applicable to non-circular GRP-UP pipes, with flexible or rigid joints, primarily intended for use in buried installations but may also be used to reline existing non-circular pipe lines.

    NOTE 1 GRP-UP includes pipes with vinyl ester liners or made entirely from vinyl ester.

    NOTE 2 Piping systems conforming to ISO 16611:2017 can be used also for non-buried applications provided the influence of the environment, e.g. from UV-radiation, and the supports are considered in the design of the pipes, fittings and joints.

    ISO 16611:2017 is applicable to pipes, fittings and their joints of nominal sizes from DN 150 to DN 4000, which are intended to be used for the conveyance of surface water or sewage at temperatures up to 50 °C.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes ISO/DIS 16611. (06/2017)
    Document Type Standard
    Publisher International Organization for Standardization
    Status Current

    Standards Referenced By This Book - (Show below) - (Hide below)

    I.S. EN ISO 11295:2017 CLASSIFICATION AND INFORMATION ON DESIGN AND APPLICATIONS OF PLASTICS PIPING SYSTEMS USED FOR RENOVATION AND REPLACEMENT (ISO 11295:2017)
    EN ISO 11295:2017 Classification and information on design and applications of plastics piping systems used for renovation and replacement (ISO 11295:2017)
    BS EN ISO 11295:2017 Classification and information on design and applications of plastics piping systems used for renovation and replacement
    ISO 11295:2017 Classification and information on design and applications of plastics piping systems used for renovation and replacement

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
    ISO 7685:1998 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of initial specific ring stiffness
    ISO 10928:2016 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use
    CEN/TR 15729:2010 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Report on the determination of mean abrasion after a defined number of test cycles
    ISO 8639:2016 Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods for leaktightness and proof of structural design of flexible joints
    ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
    CEN/TS 14632:2012 Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the assessment of conformity
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    ISO 8533:2003 Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin Test methods to prove the design of cemented or wrapped joints
    ISO 8513:2016 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the initial longitudinal tensile strength
    ISO 10468:2003 Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor
    ISO 10952:2014 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Determination of the resistance to chemical attack for the inside of a section in a deflected condition
    ISO 178:2010 Plastics Determination of flexural properties
    ISO 4633:2015 Rubber seals — Joint rings for water supply, drainage and sewerage pipelines — Specification for materials
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective