ISO 18563-3:2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 3: Combined systems
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
01-05-2024
French, English
08-12-2015
ISO 18563-3:2015 addresses ultrasonic test systems implementing linear phased array probes, in contact (with or without wedge) or in immersion, with centre frequencies in the range of 0,5 MHz?10 MHz.
It provides methods and acceptance criteria for verifying the performance of combined equipment (i.e. instrument, probe and cables connected). The methods described are suitable for users working under on-site or shop floor conditions. Its purpose is for the verification of the correct operation of the system prior to testing, and also the characterization of sound beams or verification of the absence of degradation of the system.
The methods are not intended to prove the suitability of the system for particular applications, but are intended to prove the capability of the combined equipment to generate ultrasonic beams according to the settings used.
The calibration of the system for a specific application is outside of the scope of part of ISO 18563 and it is intended that it be covered by the test procedure.
ISO 18563-3:2015 does not address the following:
- encircling arrays;
- series of apertures having a different number of elements;
- different settings for transmitting and receiving (e.g. active aperture, number of active elements, delays);
- techniques using post-processing of the signals of individual elements in a more complex manner than a simple delay law (e.g. full matrix capture).
Committee |
ISO/TC 135/SC 3
|
DevelopmentNote |
Supersedes ISO/DIS 18563-3. (12/2015)
|
DocumentType |
Standard
|
Pages |
37
|
PublisherName |
International Organization for Standardization
|
Status |
Superseded
|
SupersededBy | |
UnderRevision |
Standards | Relationship |
UNE-EN ISO 18563-3:2016 | Identical |
NF EN ISO 18563-3 : 2016 | Identical |
NBN EN ISO 18563-3 : 2016 | Identical |
NEN EN ISO 18563-3 : 2016 | Identical |
NS EN ISO 18563-3 : 2015 | Identical |
I.S. EN ISO 18563-3:2015 | Identical |
PN EN ISO 18563-3 : 2016 | Identical |
SN EN ISO 18563-3:2016 | Identical |
UNI EN ISO 18563-3 : 2016 | Identical |
BS EN ISO 18563-3:2015 | Identical |
EN ISO 18563-3:2015 | Identical |
DIN EN ISO 18563-3:2016-06 | Identical |
DS EN ISO 18563-3 : 2015 | Identical |
BS EN ISO 18563-1:2015 | Non-destructive testing. Characterization and verification of ultrasonic phased array equipment Instruments |
EN ISO 22825:2017 | Non-destructive testing of welds - Ultrasonic testing - Testing of welds in austenitic steels and nickel-based alloys (ISO 22825:2017) |
BS EN ISO 18563-2:2017 | Non-destructive testing. Characterization and verification of ultrasonic phased array equipment Probes |
DIN EN ISO 18563-1:2015-11 | Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 1: Instruments (ISO 18563-1:2015) |
ISO 22825:2017 | Non-destructive testing of welds — Ultrasonic testing — Testing of welds in austenitic steels and nickel-based alloys |
ISO 19675:2017 | Non-destructive testing Ultrasonic testing Specification for a calibration block for phased array testing (PAUT) |
I.S. EN ISO 18563-2:2017 | NON-DESTRUCTIVE TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC PHASED ARRAY EQUIPMENT - PART 2: PROBES (ISO 18563-2:2017) |
BS EN ISO 22825:2017 | Non-destructive testing of welds. Ultrasonic testing. Testing of welds in austenitic steels and nickel-based alloys |
I.S. EN ISO 22825:2017 | NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING - TESTING OF WELDS IN AUSTENITIC STEELS AND NICKEL-BASED ALLOYS (ISO 22825:2017) |
ISO 18563-1:2015 | Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 1: Instruments |
ISO 18563-2:2017 | Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 2: Probes |
UNE-EN ISO 18563-1:2016 | Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 1: Instruments (ISO 18563-1:2015) |
EN ISO 18563-1:2015 | Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 1: Instruments (ISO 18563-1:2015) |
EN ISO 18563-2:2017 | Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 2: Probes (ISO 18563-2:2017) |
BS ISO 19675:2017 | Non-destructive testing. Ultrasonic testing. Specification for a calibration block for phased array testing (PAUT) |
EN 16392-2:2014 | Non-destructive testing - Characterisation and verification of ultrasonic phased array equipment - Part 2: Probes |
EN 12668-2:2010 | Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 2: Probes |
ISO 2400:2012 | Non-destructive testing — Ultrasonic testing — Specification for calibration block No. 1 |
EN 16018:2011 | Non-destructive testing - Terminology - Terms used in ultrasonic testing with phased arrays |
EN 1330-4:2010 | Non-destructive testing - Terminology - Part 4: Terms used in ultrasonic testing |
ISO 7963:2006 | Non-destructive testing — Ultrasonic testing —- Specification for calibration block No. 2 |
ISO 18563-1:2015 | Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 1: Instruments |
ISO 5577:2017 | Non-destructive testing — Ultrasonic testing — Vocabulary |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.