Skip to content
Please enter a keyword to search

  • L-P-410 Revision A:1966

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    PLASTIC, POLYAMIDE (NYLON), RIGID: RODS, TUBES, FLATS, MOLDED AND CAST PARTS

    Available format(s):  PDF

    Superseded date:  24-12-2019

    Language(s): 

    Published date: 

    Publisher:  US Military Specs/Standards/Handbooks

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1 SCOPE AND CLASSIFICATION
    2 APPLICABLE DOCUMENTS
    3 REQUIREMENTS
    4 QUALITY ASSURANCE PROVISIONS
    5 PREPARATION FOR DELIVERY
    6 NOTES

    Abstract - (Show below) - (Hide below)

    Describes the requirements of rigid plastic polyamide (nylon) molded and cast parts, rods, tubing, bushing stock, tubular bar, and flats for mechanical and electrical applications.

    General Product Information - (Show below) - (Hide below)

    Committee FSC 9330
    Development Note New child NOT 1 2022 is added.
    Document Type Standard
    Product Note New child NOT 1 2022 is added.
    Publisher US Military Specs/Standards/Handbooks
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    MIL S 24317 : 0 SWITCH, MULTI-STATION, PUSHBUTTON (ILLUMINATED AND NON-ILLUMINATED), GENERAL SPECIFICATION FOR
    MIL-DTL-39024-14 Revision C:2008 CONNECTORS, ELECTRICAL, TEST POINT TYPE, PANEL TYPE; SINGLE TEST POINT SUBMINIATURE (PUSH-IN), LOW VOLTAGE, .080
    MIL-I-81969 Revision B:1982 INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, GENERAL SPECIFICATION FOR
    MIL-DTL-39024-15 Revision C:2008 CONNECTORS, ELECTRICAL, TEST POINT TYPE, PRINTED WIRING TYPE; SINGLE TEST POINT, LOW VOLTAGE, .080
    MIL C 39024 : A CONNECTOR, ELECTRICAL, TEST POINT TYPE, PANEL TYPE, SINGLE TEST POINT (THREADED), HIGH VOLTAGE
    MIL-DTL-39024-13 Revision D:2011 CONNECTORS, ELECTRICAL, TEST POINT TYPE, PRINTED WIRING TYPE; SINGLE TEST POINT (RIGHT ANGLE, 2-LEG MOUNTING), LOW VOLTAGE, .080
    MIL I 45932 : 0 INSERT, SCREW THREAD, THIN WALL, LOCK IN
    SAE AS 50151 : 2015 CONNECTORS, ELECTRICAL, CIRCULAR THREADED, AN TYPE, GENERAL SPECIFICATION FOR
    MIL-W-45595 Revision D:1985 WASHER, RECESSED, SADDLE AND SHOULDERED METAL
    MIL-DTL-24317 Revision B:2010 SWITCHES, MULTISTATION, PUSHBUTTON, ILLUMINATED AND NON-ILLUMINATED), GENERAL SPECIFICATION FOR
    MIL J 39024/11 : F JACK, TIP, TEST POINT TYPE, PRINTED WIRING TYPE, SINGLE TEST POINT, RIGHT ANGLE, 2-LEG MOUNTING, LOW VOLTAGE, .080
    MIL-DTL-28754-35 Revision F:2015 CONNECTORS, ELECTRICAL, MODULAR, CONNECTOR, TYPE 3, MALE CONTACT AND INSULATOR BUSHING SET, REMOVABLE WIRE WRAPPOST TERMINAL
    MIL-DTL-39024-11 Revision G:2012 Jack, Tip, Test Point Type, Printed Wiring Type, Single Test Point, Right Angle, 2-Leg Mounting, Low Voltage, .080
    MIL-C-24217 Revision A:1984 CONNECTOR, ELECTRICAL, DEEP SUBMERGENCE, SUBMARINE
    GG-S-161 Revision D:1985 SCALES, DRAFTING, AND SCALES, PLOTTING (GENERAL SPECIFICATION)
    MIL-DTL-28754 Revision E:2016 Connectors, Electrical, Modular, and Component Parts General Specification for
    ASTM D 4066 : 2013 Standard Classification System for Nylon Injection and Extrusion Materials (PA)
    MIL-DTL-5015 Revision H:2000 CONNECTORS, ELECTRICAL, CIRCULAR THREADED, AN TYPE - GENERAL SPECIFICATION FOR
    MIL-DTL-45932 Revision A:2015 INSERT, SCREW THREAD, THIN WALL, LOCKED IN: GENERAL SPECIFICATION FOR
    MIL-DTL-28754-37 Revision E:2015 CONNECTORS, ELECTRICAL, MODULAR, CONNECTOR, TYPE 3, FEMALE CONTACT AND POLARIZING BUSHING SET, REMOVABLE WIRE WRAPPOST TERMINAL
    MIL-DTL-55116 Revision D:2013 CONNECTORS: MINIATURE AUDIO, FIVE-PIN AND SIX-PIN - GENERAL SPECIFICATION FOR
    MIL S 22710 : E SWITCHES, ROTARY (PRINTED CIRCUIT), (THUMBWHEEL, INLINE, AND PUSHBUTTON), GENERAL SPECIFICATION FOR
    MIL-DTL-2 Revision G:2006 VALVES, CYLINDER, GAS (FOR COMPRESSED OR LIQUEFIED GASES), GENERAL SPECIFICATION FOR
    MIL-STD-808 Revision A:1983 FINISH, MATERIALS AND PROCESSES FOR CORROSION PREVENTION AND CONTROL IN SUPPORT EQUIPMENT
    MIL-DTL-32286 Base Document:2008 MATERIAL, BALL VALVE SEAT SEAL AND THRUST WASHER
    MIL-DTL-28754-34 Revision E:2015 CONNECTORS, ELECTRICAL, MODULAR, CONNECTOR, TYPE 3, FEMALE CONTACT AND INSULATOR BUSHING SET, REMOVABLE WIRE WRAPPOST TERMINAL
    H-H-001193 Revision A:1971 HAIRBRUSH, SYNTHETIC
    MIL-C-22442-2 Revision C:1992 CABLE ASSEMBLY, RADIO FREQUENCY (AIRCRAFT AUDIO), MOLDED RUBBER CONNECTOR (QUICK DISCONNECT)
    MS16051 Revision G:2014 COUPLING, GROUND COOLING, COMBAT TYPE AIRCRAFT
    MIL-C-8956 Revision A:1970 CLAMP, LOOP TUBE SUPPORT
    MIL C 5015 : G CONNECTOR, ELECTRICAL, CIRCULAR THREADED AN TYPE, GENERAL SPECIFICATION FOR
    MIL-DTL-39024-10 Revision F:2015 JACK, TIP (TEST POINT TYPE, PANEL TYPE; SINGLE TEST POINT (THREADED) LOW VOLTAGE, .080)
    MIL C 28754 : D CONNECTOR, ELECTRICAL, MODULAR AND COMPONENT PARTS, GENERAL SPECIFICATION FOR
    SAE AS 81969 : 2016 INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, GENERAL SPECIFICATION FOR
    MIL C 55116 : B CONNECTOR, MINIATURE AUDIO, FIVE PIN
    MIL-DTL-55302-78 Revision D:2004 Connectors, Printed Circuit Subassembly and Accessories: Key, Polarizing, Connectors, Electrical Printed Wiring Boards

    Standards Referencing This Book - (Show below) - (Hide below)

    MIL-S-18729 Revision C:1965 STEEL PLATE, SHEET, AND STRIP, ALLOY, 4130, AIRCRAFT QUALITY
    MIL-STD-129 Revision R:2014 Military Marking for Shipment and Storage
    MIL-S-81087 Revision C:1981 SILICONE FLUID, CHLORINATED PHENYL METHYL POLYSILOXANE, NATO CODE NUMBER H-536
    PPP-B-636 Revision J:1981 BOX, SHIPPING, FIBERBOARD
    PPP-B-576 Revision C:1993 BOX, WOOD-CLEATED PANELBOARD
    QQ-C-576 Revision B:1961 COPPER FLAT PRODUCTS WITH SLIT, SLIT AND EDGE-ROLLED, SHEARED, SAWED OR MACHINED EDGES, (PLATE, BAR, SHEET, AND STRIP)
    FED-STD-406 Revision A:1982 PLASTIC, METHODS OF TESTING
    FED-STD-123 Revision H:2007 MARKING FOR SHIPMENT (CIVIL AGENCIES)
    PPP-B-591 Revision B:1971 BOXES, SHIPPING, FIBERBOARD, WOOD-CLEATED
    MIL-P-116 Revision J:1988 PRESERVATION, METHODS OF
    PPP-B-601 Revision H:1989 BOXES, WOOD, CLEATED PLYWOOD
    MIL-L-10547 Revision E:1975 LINERS, CASE, AND SHEET, OVERWRAP; WATER-VAPORPROOF OR WATERPROOF, FLEXIBLE
    FED-STD-102 Revision B:1963 PRESERVATION, PACKAGING, AND PACKING LEVELS
    PPP-B-621 Revision D:1981 BOXES, WOOD, NAILED AND LOCK CORNER
    MIL-STD-105 Revision E:1989 SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES
    PPP-B-585 Revision D:1992 BOX, WOOD, WIREBOUND
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective