MIL-T-6845 Revision D:1985
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
TUBING, STEEL, CORROSION-RESISTANT (S30400), AEROSPACE VEHICLE HYDRAULIC SYSTEM 1/8 HARD CONDITION (S/S BY SAE-AMS-T-6845)
26-04-1985
01-01-1999
Specifies thin walled corrosion resistant special quality, steel tubing in 1/8 hard condition, for high pressure hydraulic systems.
| DevelopmentNote |
INACTIVE FOR NEW DESIGN, DOCUMENT VALID FOR ACQUISITION WHEN NEEDED. NOTICE 4 - NOTICE OF CANCELLATION: Users may refer to SAE-AMS-T-6845 as a possible replacement but are cautioned to evaluate SAE-AMS-T-6845 for their particular application before citing it as a replacement document.
|
| DocumentType |
Standard
|
| Pages |
16
|
| PublisherName |
US Military Specs/Standards/Handbooks
|
| Status |
Superseded
|
This specification presents requirements for thin-walled (inside diameter greater than four times the wall thickness and outside diameter 1/4 inch and larger) corrosion-resistant steel tubing in approximately the 1/8 hard condition, of special quality, suitable for use in high-pressure hydraulic systems.
| Standards | Relationship |
| SAE AMS5564C | Similar to |
| SAE AMST6845B | Similar to |
| SAE AMS5566M | Identical |
| SAE MA2005B | Tube Fittings, Aerospace Fluid Systems, Separable, For 24° Cone, General Specification, Metric (ISO 7169) |
| MIL H 25579 : E | HOSE ASSEMBLY, TETRAFLUOROETHYLENE, HIGH TEMPERATURE MEDIUM PRESSURE, GENERAL REQUIREMENTS FOR |
| MIL BULL 343 : A | DOCUMENTS APPLICABLE TO AIRCRAFT ENGINES AND PROPELLERS, USE OF |
| MIL-H-25475 Revision B:1971 | Hydraulic Systems, Missile Design, Installation and Tests, General Requirements for (No S/S Document) |
| MIL-H-8891 Revision A:1978 | Hydraulic Systems, Manned Flight Vehicles, Type III Design, Installation and Data Requirements for, General Specification for |
| MIL-H-5440 Revision H:1993 | Hydraulic Systems, Aircraft, Design and Installation Requirements for (S/S by SAE-AS5440) |
| SAE AIR1388B | Service Damage Limits for Aircraft Hydraulic Tubing |
| SAE AIR5005A | Aerospace - Commercial Aircraft Hydraulic Systems |
| MIL-F-45764 Revision C:1990 | Fluid Lines and Fittings for Missiles and Related Ground Equipment: Fabrication and Installation of (No S/S Document) |
| SAE AS1553A | Performance Standard for Tube Support Loop-Cushioned Clamp |
| MIL-F-18280 Revision F:1995 | Fittings, Flareless Tube, Fluid Connection (S/S by SAE-AS18280) |
| SAE ARP618A | Boss Fittings, Metal Seal, Fluid Systems: General Requirements For |
| MIL-C-8956 Revision A:1970 | Clamps, Loop, Tube Support (For Future Req. use MIL-C-8603 and MIL-C-85052 |
| MIL V 25675 : B | VALVE, CHECK, MINIATURE, HYDRAULIC, AIRCRAFT AND MISSILE |
| SAE AS4444 | Fittings, 24° Cone Flareless, Fluid Connection, 5000 psi |
| SAE ARP1185B | Flexure Testing of Hydraulic Tubing Joints and Fittings |
| MIL-STD-129 Revision R:2014 | Military Marking for Shipment and Storage |
| QQ-P-35 Revision C:1988 | Passivation Treatments for Corrosion-Resistant Steel (S/Sby ASTM-A967or SAE-AMS-QQ-P-35) |
| MIL-H-6875 Revision H:1989 | Heat Treatment of Steel, Process for (S/S by SAE-AMS-H-6875) |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| AND10104 : REV 5 | TUBING, STEEL, CORROSION RESISTANT, ROUND, STANDARD DIMENSIONS FOR |
| MIL-STD-753 Revision C:1990 | CORROSION-RESISTANT STEEL PARTS: SAMPLING, INSPECTION AND TESTING FOR SURFACE PASSIVATION (S/S BY SAE-AMS-STD-753) |
| MS33584 Revision C:1990 | TUBING END STANDARD DIMENSIONS FOR FLARED (S/S BY SAE-AS4330) |
| MIL-STD-163 Revision C:1978 | Steel Mill Products Preparation for Shipment and Storage (S/S by ASTM-A700) |
| FED-STD-183 Revision C:1980 | CONTINUOUS IDENTIFICATION MARKING OF IRON AND STEEL PRODUCTS (SEE NOTICE 3 FOR REPLACEMENT INFORMATION) |
| SAE AMS2243K | Tolerances Corrosion and Heat-Resistant Steel Tubing |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.