NF EN 60751 : 2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
INDUSTRIAL PLATINUM RESISTANCE THERMOMETERS AND PLATINUM TEMPERATURE SENSORS
01-04-2022
12-01-2013
AVANT-PROPOS
1 Domaine d'application
2 Références normatives
3 Termes et définitions
4 Caractéristiques
4.1 Relations température/résistance
4.2 Valeurs de résistance
5 Exigences générales
5.1 Classes de tolérance
5.2 Courant de mesure
5.3 Alimentation électrique
5.4 Configuration des fils de connexion
6 Essais
6.1 Généralités
6.2 Essais individuels de production pour les résistances
6.3 Essais individuels de production pour les thermomètres
6.4 Essais de type pour les résistances
6.5 Essais de type pour les thermomètres
6.6 Essais de type complémentaires pour les applications
spéciales des thermomètres
6.7 Résumé des essais
7 Informations à mettre à disposition par le fabricant
7.1 Pour les résistances uniquement
7.2 Pour les résistances et/ou les thermomètres
8 Identification des thermomètres et marquage
Annexe ZA (normative) Références normatives à d'autres
publications internationales avec les
publications européennes correspondantes
Specifies requirements for industrial platinum resistance thermometer sensors whose electrical resistance is a defined function of temperature. Covers thermometers suitable for all or part of the temperature range -200 degrees C to +850 degrees C with two tolerance classes. Also describes methods of test to prove compliance with this standard and suitable apparatus for some of the tests.
| DevelopmentNote |
Indice de classement: C42-330. PR NF EN 60751 May 2007. (05/2007)
|
| DocumentType |
Standard
|
| PublisherName |
Association Francaise de Normalisation
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| DIN EN 60751:2009-05 | Identical |
| IEC 60751:2008 | Identical |
| I.S. EN 60751:2008 | Identical |
| EN 60751:2008 | Identical |
| BS EN 60751:2008 | Identical |
| UNE-EN 60751:1996 | Identical |
| NF EN 60947-8 : 2003 AMD 2 2012 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 8: CONTROL UNITS FOR BUILT-IN THERMAL PROTECTION (PTC) FOR ROTATING ELECTRICAL MACHINES |
| NF EN 60068-3-6 : 2002 | ENVIRONMENTAL TESTING - PART 3-6: SUPPORTING DOCUMENTATION AND GUIDANCE - CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE/HUMIDITY CHAMBERS |
| NF EN ISO 18472 : 2006 | STERILIZATION OF HEALTH CARE PRODUCTS - BIOLOGICAL AND CHEMICAL INDICATORS - TEST EQUIPMENT |
| FD X15 140 : 2013 FD | MESURE DE L'HUMIDITE DE L'AIR - ENCEINTES CLIMATIQUES ET THERMOSTATIQUES - CARACTERISATION ET VERIFICATION |
| NF ISO 13737 : 2004 | PETROLEUM PRODUCTS AND LUBRICANTS - DETERMINATION OF LOW-TEMPERATURE CONE PENETRATION OF LUBRICATING GREASES |
| NFX 15 140 : 2002 | MEASUREMENT OF AIR MOISTURE - CLIMATIC AND THERMOSTATIC CHAMBERS - CHARACTERISATION AND VERIFICATION |
| NFS 98 030 : 2012 | STORAGE CABINETS FOR HEAT SENSITIVE ENDOSCOPES |
| NF ISO 14661 : 2000 AMD 1 2004 | THERMAL TURBINES FOR INDUSTRIAL APPLICATIONS (STEAM TURBINES, GAS EXPANSION TURBINES) - GENERAL REQUIREMENTS |
| NF EN 60068-3-5 : 2002 | ENVIRONMENTAL TESTING - PART 3-5: SUPPORTING DOCUMENTATION AND GUIDANCE - CONFIRMATION OF THE PERFORMANCE OF TEMPERATURE CHAMBERS |
| NF EN ISO 4625-1 : 2006 | BINDERS FOR PAINTS AND VARNISHES - DETERMINATION OF SOFTENING POINT - PART 1: RING-AND-BALL METHOD |
| FD V08 601 : 2005 FD | MICROBIOLOGIE OF FOOD AND ANIMAL FEEDING STUFFS - THERMOSTATIC CHAMBERS - CHARACTERISATION, VERIFICATION AND DAILY FOLLOW-UP |
| FD X07 029-1 : 2002 FD | METROLOGY - CALIBRATION AND VERIFICATION PROCEDURE FOR THERMOMETERS - PART 1: CALIBRATION AND VERIFICATION PROCEDURE FOR PROBES AND RESISTANCE THERMOMETERS |
| NF EN 60068-3-7 : 2002 | ENVIRONMENTAL TESTING - PART 3-7: SUPPORTING DOCUMENTATION AND GUIDANCE - MEASUREMENTS IN TEMPERATURE CHAMBERS FOR TESTS A AND TEST B (WITH LOAD) |
| NF EN 61298-1 : 2009 | PROCESS MEASUREMENT AND CONTROL DEVICES - GENERAL METHODS AND PROCEDURES FOR EVALUATING PERFORMANCE - PART 1: GENERAL CONSIDERATIONS |
| IEC 61298-1:2008 | Process measurement and control devices - General methods and procedures for evaluating performance - Part 1: General considerations |
| NF EN 61152 : 1994 | DIMENSIONS OF METAL-SHEATHED THERMOMETER ELEMENTS |
| IEC 61152:1992 | Dimensions of metal-sheathed thermometer elements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.