NF EN 61557-12 : 2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ELECTRICAL SAFETY IN LOW VOLTAGE DISTRIBUTION SYSTEMS UP TO 1000 V A.C. AND 1500 V D.C. - EQUIPMENT FOR TESTING, MEASURING OR MONITORING OF PROTECTIVE MEASURES - PART 12: PERFORMANCE MEASURING AND MONITORING DEVICES (PMD)
31-03-2022
12-01-2013
AVANT-PROPOS
INTRODUCTION
1 Domaine d'application
2 Références normatives
3 Termes et définitions
3.1 Définitions générales
3.2 Définitions relatives à l'incertitude et à la performance
3.3 Définitions se rapportant aux phénomènes électriques
3.4 Définitions relatives aux techniques de mesure
3.5 Notations
4 Exigences
4.1 Exigences générales
4.2 Architecture générale d'un PMD
4.3 Classification des PMD
4.4 Liste des classes de performance applicables
4.5 Conditions de référence et de fonctionnement pour
les PMD
4.6 Conditions de démarrage
4.7 Exigences relatives aux fonctions des PMD (sauf PMD-A)
4.8 Exigences relatives aux fonctions des PMD-A
4.9 Exigences mécaniques générales
4.10 Exigences de sécurité
4.11 Sorties analogiques
5 Marquage et instructions de fonctionnement
5.1 Marquage
5.2 Instructions de fonctionnement et d'installation
6 Essais
6.1 Essais de type des PMD
6.2 Essais de type des PMD-A
6.3 Essais individuels de série
Annexe A (informative) Définitions des paramètres
électriques
Annexe B (normative) Définitions des valeurs minimale,
maximale, crête et moyenne
Annexe C (informative) Incertitude intrinsèque, incertitude
de fonctionnement et incertitude globale du système
Annexe D (informative) Classes de capteurs recommandées
pour les différents types de PMD
Annexe E (normative) Exigences applicables aux PMD et aux
PMD-A
Annexe ZA (normative) Références normatives à d'autres
publications internationales avec les publications
européennes correspondantes
Annexe ZZ (informative) Couverture des Exigences
Essentielles des Directives CE
Bibliographie
La présente partie de la CEI 61557 spécifie des exigences pour les dispositifs combinés de mesure et de surveillance des performances, qui mesurent et surveillent les paramètres électriques dans les réseaux de distribution électrique. Ces exigences définissent également les performances, dans les réseaux alternatifs ou continus monophasés et triphasés, ayant des tensions assignées inférieures ou égales à 1000 V en courant alternatif ou inférieures ou égales à 1500 V en courant continu.
| DevelopmentNote |
Indice de classement: C42-198-12PR. PR NF EN 61557-12 September 2006. (09/2006) PR NF EN 61557-12 April 2017. (05/2017)
|
| DocumentType |
Standard
|
| PublisherName |
Association Francaise de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| IEC 61557-12:2007 | Identical |
| EN 61557-12:2008 | Identical |
| FD X30 147 : 2015 FD | MEASUREMENT PLAN FOR ENERGY PERFORMANCE MONITORING - DESIGN AND IMPLEMENTATION |
| NF EN 62053-31 : 1998 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 31: PULSE OUTPUT DEVICES FOR ELECTROMECHANICAL AND ELECTRONIC METERS (TWO WIRES ONLY) |
| IEC 62053-23:2003+AMD1:2016 CSV | Electricity metering equipment (a.c.) - Particular requirements -Part 23: Static meters for reactive energy (classes 2 and 3) |
| IEC 62053-21:2003+AMD1:2016 CSV | Electricity metering equipment (a.c.) - Particular requirements - Part 21: Static meters for active energy (classes 1 and 2) |
| NF EN 61326-1 : 2013 | ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL AND LABORATORY USE - EMC REQUIREMENTS - PART 1: GENERAL REQUIREMENTS |
| NF EN 61557-1 : 2007 | ELECTRICAL SAFETY IN LOW VOLTAGE DISTRIBUTION SYSTEMS UP TO 1000 V A.C. AND 1500 V D.C. - EQUIPMENT FOR TESTING, MEASURING OR MONITORING OF PROTECTIVE MEASURES - PART 1: GENERAL REQUIREMENTS |
| NF EN 60068-2-2 : 2007 | ENVIRONMENTAL TESTING - PART 2-2: TESTS - TESTS B: DRY HEAT |
| NF EN 60529 : 92 AMD 2 2014 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) |
| IEC 61557-1:2007 | Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 1: General requirements |
| NF EN 61010-1 : 2011 | SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL AND LABORATORY USE - PART 1: GENERAL REQUIREMENTS |
| IEC 62053-31:1998 | Electricity metering equipment (a.c.) - Particular requirements - Part 31: Pulse output devices for electromechanical and electronic meters (two wires only) |
| NF EN 61000-4-30 : 2015 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-30: TESTING AND MEASUREMENT TECHNIQUES - POWER QUALITY MEASUREMENT METHODS |
| IEC 60364-6:2016 | Low voltage electrical installations - Part 6: Verification |
| NF EN 61000 4-15 : 2012 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-15: TESTING AND MEASUREMENT TECHNIQUES - FLICKERMETER - FUNCTIONAL AND DESIGN SPECIFICATIONS |
| NF EN 60068-2-1 : 2007 | ENVIRONMENTAL TESTING - PART 2-1: TESTS - TESTS A: COLD |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| NF EN 62053-21 : 2003 AMD 1 2017 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 21: STATIC METERS FOR ACTIVE ENERGY (CLASSES 1 AND 2) |
| NF EN 62053-23 : 2003 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 23: STATIC METERS FOR REACTIVE ENERGY (CLASSES 2 AND 3) |
| IEC 62053-22:2003+AMD1:2016 CSV | Electricity metering equipment (a.c.) - Particular Requirements - Part 22: Static meters for active energy (classes 0,2 S and 0,5 S) |
| NF EN 60068 2-30 : 2006 | ENVIRONMENTAL TESTING - PART 2-30: TESTS - TEST DB AND GUIDANCE: DAMP HEAT, CYCLIC (12 H + 12 H CYCLE) |
| IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| NF EN 62053-22 : 2003 AMD 1 2017 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS PART 22: STATIC METERS FOR ACTIVE ENERGY (CLASSES 0,2 S AND 0,5 S) |
| IEC 61010-1:2010+AMD1:2016 CSV | Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements |
| IEC 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.