Skip to content
Please enter a keyword to search

  • NF EN ISO 1133 : 2005

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THERMOPLASTICS

    Available format(s): 

    Superseded date:  01-02-2012

    Language(s): 

    Published date:  12-01-2013

    Publisher:  Association Francaise de Normalisation

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Avant-propos
    1 Domaine d'application
    2 Références normatives
    3 Termes et définitions
    4 Principe
    5 Appareillage
       5.1 Plastomère d'extrusion
       5.2 Équipement accessoire
    6 Échantillon d'essai
       6.1 Forme de l'échantillon
       6.2 Conditionnement
    7 Étalonnage de la température, nettoyage et entretien
       de l'appareillage
       7.1 Étalonnage du système de régulation de la température
       7.2 Nettoyage de l'appareillage
    8 Mode opératoire A: Méthode de mesurage de la masse
       8.1 Choix de la température et de la charge
       8.2 Nettoyage
       8.3 Choix de la masse de l'échantillon et chargement du
           cylindre
       8.4 Mesurages
       8.5 Expression des résultats
    9 Mode opératoire B: Méthode de mesurage du volume déplacé
       9.1 Choix de la température et de la charge
       9.2 Distance minimale de déplacement du piston
       9.3 Chronomètre
       9.4 Prétraitement pour l'essai
       9.5 Mesurages
       9.6 Expression des résultats
    10 Rapport des vitesses d'écoulement (FRR)
    11 Fidélité
    12 Rapport d'essai
    Annexe A (normative) Conditions d'essai pour la détermination
                         du MFR et du MVR
    Annexe B (informative) Conditions spécifiées dans les Normes
                           internationales pour la détermination
                           de l'indice de fluidité à chaud des
                           matériaux thermoplastiques

    Abstract - (Show below) - (Hide below)

    Provides two procedures for the determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastic materials under specified conditions of temperature and load.

    General Product Information - (Show below) - (Hide below)

    Development Note Indice de classement: T51-038. PR NF EN ISO 1133 September 2003. (09/2003)
    Document Type Standard
    Publisher Association Francaise de Normalisation
    Status Superseded

    Standards Referenced By This Book - (Show below) - (Hide below)

    NFP 16 345-2 : 2003 CONCRETE PIPES AND FITTINGS, UNREINFORCED, STEEL FIBRE AND REINFORCED - PART 2: NATIONAL SPECIFICATION
    XP A35 037-1 : 2003 XP STEEL PRODUCTS - PROTECTED AND SHEATHED HIGH STRENGTH STEEL STRANDS - PART 1: GENERAL REQUIREMENTS
    NF EN ISO 20568-2 : 2017 PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    NF EN ISO 8257-2 : 2006 PLASTICS - POLY(METHYL METHACRYLATE) (PMMA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    NF EN ISO 2580-2 : 2004 PLASTICS - ACRYLONITRILE-BUTADIENE-STYRENE (ABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    NF EN ISO 15013 : 2007 PLASTICS - EXTRUDED SHEETS OF POLYPROPYLENE (PP) - REQUIREMENTS AND TEST METHODS
    NF EN 13476-3 : 2007 + A1 2009 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INSIDE AND PROFILED OUTSIDE SURFACE, TYPE B
    NF EN 13476-2 : 2007 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INSIDE AND OUTSIDE SURFACE, TYPE A
    NF EN 14628 : 2006 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYETHYLENE COATING FOR PIPES - REQUIREMENTS AND TEST METHODS
    NF EN ISO 10366-2 : 2004 PLASTICS - METHYL METHACRYLATE-ACRYLONITRILE-BUTADIENE-STYRENE (MABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    NF EN 15344 : 2008 PLASTICS - RECYCLED PLASTICS - CHARACTERISATION OF POLYETHYLENE (PE) RECYCLATES
    NF EN ISO 2897-2 : 2004 PLASTICS - IMPACT-RESISTANT POLYSTYRENE (PS-I) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective