• NF EN ISO 2897-2 : 2004

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    PLASTICS - IMPACT-RESISTANT POLYSTYRENE (PS-I) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES

    Available format(s): 

    Superseded date:  27-10-2021

    Language(s): 

    Published date:  12-01-2013

    Publisher:  Association Francaise de Normalisation

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Conformance
    3 Normative references
    4 Preparation of test specimens
    5 Conditioning of test specimens
    6 Determination of properties

    Abstract - (Show below) - (Hide below)

    Describes the methods of preparation of test specimens and the test methods to be used in determining the properties of PS-I moulding and extrusion materials.

    General Product Information - (Show below) - (Hide below)

    Development Note Indice de classement : T53-034-2 (06/2004)
    Document Type Standard
    Publisher Association Francaise de Normalisation
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
    IEC 60695-11-20:2015 Fire hazard testing - Part 11-20: Test flames - 500 W flame test method
    IEC 60112:2003+AMD1:2009 CSV Method for the determination of the proof and the comparative tracking indices of solid insulating materials
    NF ISO 1656 : 2015 RUBBER, RAW NATURAL, AND RUBBER LATEX, NATURAL - DETERMINATION OF NITROGEN CONTENT
    NF EN ISO 3167 : 2014 PLASTICS - MULTIPURPOSE TEST SPECIMENS
    IEC 60250:1969 Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths
    NF EN ISO 4589-2 : 2017 PLASTICS - DETERMINATION OF BURNING BEHAVIOUR BY OXYGEN INDEX - PART 2: AMBIENT-TEMPERATURE TEST
    NF EN ISO 306 : 2014 PLASTICS - THERMOPLASTIC MATERIALS - DETERMINATION OF VICAT SOFTENING TEMPERATURE (VST)
    NF EN ISO 293 : 2005 PLASTICS - COMPRESSION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS
    NF EN ISO 178 : 2011 AMD 1 2013 PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES
    NF EN ISO 11357-2 : 2014 PLASTICS - DIFFERENTIAL SCANNING CALORIMETRY (DSC) - PART 2: DETERMINATION OF GLASS TRANSITION TEMPERATURE AND GLASS TRANSITION STEP HEIGHT
    NF EN ISO 75-2 : 2013 PLASTICS - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD - PART 2: PLASTICS AND EBONITE
    ISO 2897-1:1997 Plastics Impact-resistant polystyrene (PS-I) moulding and extrusion materials Part 1: Designation system and basis for specifications
    NF EN ISO 294-1 : 2017 PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 1: GENERAL PRINCIPLES, AND MOULDING OF MULTIPURPOSE AND BAR TEST SPECIMENS
    NF EN ISO 179 : 1997
    ISO 1183:1987 Plastics Methods for determining the density and relative density of non-cellular plastics
    IEC 60296:2012 RLV Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear
    IEC 60093:1980 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
    ISO 2561:2012 Plastics — Determination of residual styrene monomer in polystyrene (PS) and impact-resistant polystyrene (PS-I) by gas chromatography
    IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
    NF EN ISO 527-4 : 1997 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - TEST CONDITIONS FOR ISOTROPIC AND ORTHOTROPIC FIBRE-REINFORCED PLASTIC COMPOSITES
    NF EN ISO 2818 : 1997 PLASTICS - PREPARATION OF TEST SPECIMENS BY MACHINING
    NF EN ISO 1133 : 2005 PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THERMOPLASTICS
    NF EN ISO 527-2 : 2012 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 2: TEST CONDITIONS FOR MOULDING AND EXTRUSION PLASTICS
    NF EN ISO 8256 : 2005 PLASTICS - DETERMINATION OF TENSILE-IMPACT STRENGTH
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective