NF EN ISO 1302 : 2002
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
GEOMETRICAL PRODUCT SPECIFICATION (GPS) - INDICATION OF SURFACE TEXTURE IN TECHNICAL PRODUCT DOCUMENTATION
04-04-2022
12-01-2013
Avant-propos
Introduction
1 Domaine d'application
2 Références normatives
3 Termes et définitions
4 Symboles graphiques pour l'indication de l'état de surface
5 Composition du symbole graphique complet pour état de surface
6 Indication des paramètres d'état de surface
7 Indication de la méthode de fabrication ou information
correspondante
8 Indication des stries de surface
9 Indication des surépaisseurs d'usinage
10 Résumé des indications des exigences d'état de surface et de
leurs valeurs
11 Position sur les dessins et autre documentation technique de
produits
Annexe A (normative) Proportions et dimensions des symboles
graphiques
Annexe B (informative) Tableaux synoptiques
Annexe C (informative) Exemples d'indication d'exigences d'état
de surface
Annexe D (informative) Indications minimales afin d'assurer une
maîtrise non ambiguë des fonctions de surface
Annexe E (informative) Désignation des paramètres d'état de surface
Annexe F (informative) Longueur d'évaluation, ln
Annexe G (informative) Bande de transmission et longueur de base
Annexe H (informative) Explication approfondie sur les conséquences
des nouvelles normes ISO en matière d'état
de surface
Annexe I (informative) Pratique antérieure
Annexe J (informative) Relation avec la matrice GPS
Bibliographie
Specifies the symbols and additional indications of surface texture to be indicated on technical drawings. The basic symbol for surface texture consists of two legs of unequal length inclined at approximately 60 Degrees to the line representing the considered surface. A bar added to the basic symbol means that the removal of material by machining is required. A circle added to the basic symbol means that removal of the material is not permitted.
DevelopmentNote |
Indice de classement: E05-016 Supersedes NF ISO 1302 (06/2002)
|
DocumentType |
Standard
|
PublisherName |
Association Francaise de Normalisation
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
ONORM EN ISO 1302 : 2002 | Identical |
NS EN ISO 1302 : 1ED 2002 | Identical |
ISO 1302:2002 | Identical |
EN ISO 1302 : 2002 | Identical |
NBN EN ISO 1302 : 2002 | Identical |
SN EN ISO 1302 : 2002 | Identical |
UNE-EN ISO 1302:2002 | Identical |
I.S. EN ISO 1302:2002 | Identical |
NEN EN ISO 1302 : 2002 | Identical |
BS EN ISO 1302:2002 | Identical |
UNI EN ISO 1302 : 2004 | Identical |
NF ISO 15407-2 : 2003 | PNEUMATIC FLUID POWER - FIVE-PORT DIRECTIONAL CONTROL VALVES, SIZES 18 MM AND 26 MM - PART 2: MOUNTING INTERFACES WITH OPTIONAL ELECTRICAL CONNECTOR |
NF EN ISO 12402-7 : 2007 AMD 1 2011 | PERSONAL FLOTATION DEVICES - PART 7: MATERIALS AND COMPONENTS - SAFETY REQUIREMENTS AND TEST METHODS |
NF EN ISO 8062-3 : 2007 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 3: GENERAL DIMENSIONAL AND GEOMETRICAL TOLERANCES AND MACHINING ALLOWANCES FOR CASTINGS |
NF ISO 4401 : 2005 | HYDRAULIC FLUID POWER - FOUR-PORT DIRECTIONAL CONTROL VALVES - MOUNTING SURFACES |
NF ISO 5599-1 : 2002 | PNEUMATIC FLUID POWER - FIVE-PORT DIRECTIONAL CONTROL VALVES - PART 1: MOUNTING INTERFACES WITHOUT ELECTRICAL CONNECTOR |
NF EN 1999-1-3 : 2007 AMD 1 2012 | EUROCODE 9: DESIGN OF ALUMINIUM STRUCTURES - PART 1-3: STRUCTURES SUSCEPTIBLE TO FATIGUE |
FD E05 051 : 2008 FD | SURFACE TEXTURE - METHODS OF MEASUREMENT - ROUGHNESS COMPARISON SPECIMENS |
NF EN 61076 4 115 : 2003 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-115: PRINTED BOARD CONNECTORS - BACKPLANE CONNECTOR FOR INFINIBAND EQUIPMENT |
NF EN 1999-1-1 : 2007 AMD 2 2014 | EUROCODE 9 - DESIGN OF ALUMINIUM STRUCTURES - PART 1-1: GENERAL STRUCTURAL RULES |
NF ISO 128-1 : 2003 | TECHNICAL DRAWINGS - GENERAL PRINCIPLES OF PRESENTATION - PART 1: INTRODUCTION AND INDEX |
NF EN ISO 10135 : 2009 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DRAWING INDICATIONS FOR MOULDED PARTS IN TECHNICAL PRODUCT DOCUMENTATION (TPD) |
NF EN 61076 4 113 : 2005 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRINTED BOARD CONNECTORS - PART 4-113: DETAIL SPECIFICATION FOR TWO-PART CONNECTORS HAVING 5 ROWS WITH A GRID OF 2,54 MM FOR PRINTED BOARDS AND BACKPLANES IN BUS APPLICATIONS |
NF EN 61076-2-105 : 2009 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-105: CIRCULAR CONNECTORS - DETAIL SPECIFICATION FOR M5 CONNECTORS WITH SCREW-LOCKING |
NF EN 50243 : 2004 | OUTDOOR BUSHINGS FOR 24 KV AND 36 KV AND FOR 5 KA AND 8 KA, FOR LIQUID FILLED TRANSFORMERS |
NF ISO 1103 : 2007 | ROAD VEHICLES - COUPLING BALLS FOR CARAVANS AND LIGHT TRAILERS - DIMENSIONS |
NF EN 60512-16-9 : 2008 | CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 16-9: MECHANICAL TESTS ON CONTACTS AND TERMINATIONS - TEST 16I: GROUNDING CONTACT SPRING HOLDING FORCE |
NFE 22 621 : 2015 | MECHANICAL TRANSMISSIONS - PRESSED-ON ASSEMBLIES ON CYLINDRICAL SHAFT - FUNCTION, REALISATION, CALCULATION |
NF ISO 13012-2 : 2009 | ROLLING BEARINGS - ACCESSORIES FOR SLEEVE TYPE LINEAR BALL BEARINGS - PART 2: BOUNDARY DIMENSIONS AND TOLERANCES FOR SERIES 5 |
NF ISO 7465 : 2008 | PASSENGER LIFTS AND SERVICE LIFTS - GUIDE RAILS FOR LIFT CARS AND COUNTERWEIGHTS - T-TYPE |
NFS 97 115 : 2011 | MEDICAL COMPRESSION AND LIGHT SUPPORT TEXTILE BANDAGES - TECHNICAL SPECIFICATIONS |
NF ISO 15218 : 2003 | PNEUMATIC FLUID POWER - 3/2 SOLENOID VALVES - MOUNTING INTERFACE SURFACES |
NF EN 61076 2 102 : 2002 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 2-102: CIRCULAR CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR PLUGS AND JACKS FOR EXTERNAL LOW VOLTAGE POWER SUPPLY |
NFE 48 401 : 2016 | HYDRAULIC FLUID POWER - TWO-, THREE- AND FOUR-PORT SCREW-IN CARTRIDGE VALVES - CAVITIES WITH ISO 725 (UN AND UNF) THREADS |
NF EN 60512-16-5 : 2008 | CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 16-5: MECHANICAL TESTS ON CONTACTS AND TERMINATIONS - TEST 16E: GAUGE RETENTION FORCE (RESILIENT CONTACTS) |
NF ISO 13012-1 : 2009 | ROLLING BEARINGS - ACCESSORIES FOR SLEEVE TYPE LINEAR BALL BEARINGS - PART 1: BOUNDARY DIMENSIONS AND TOLERANCES FOR SERIES 1 AND 3 |
NF ISO 5599-2 : 2002 AMD 1 2004 | PNEUMATIC FLUID POWER - FIVE-PORT DIRECTIONAL CONTROL VALVES - PART 2: MOUNTING INTERFACE SURFACES WITH OPTIONAL ELECTRICAL CONNECTOR |
NFT 70 537 : 2009 | ENERGETIC MATERIALS FOR DEFENCE - DOSSIER DEFINING THE 120 MM DIAMETER METALLIC STRUCTURE MODEL FOR SOLID PROPELLANT (PROPERGOL) |
NF EN 61076 4-114 : 2005 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-114: PRINTED BOARD CONNECTORS - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR WITH INTEGRATED SHIELDING FUNCTION HAVING A GRID OF 1 MM X 1,5 MM |
NF EN ISO 3098-2 : 2000 | TECHNICAL PRODUCT DOCUMENTATION - LETTERING - PART 2: LATIN ALPHABET, NUMERALS AND MARKS |
NF ISO 10209-1 : 1999 | TECHNICAL PRODUCT DOCUMENTATION - VOCABULARY - PART 1: TERMS RELATING TO TECHNICAL DRAWINGS: GENERAL AND TYPES OF DRAWINGS |
NF ISO 10135 : 1995 | TECHNICAL DRAWINGS - SIMPLIFIED REPRESENTATION OF MOULDED, CAST AND FORGED PARTS |
NF EN ISO 4287 : 1998 AMD 1 2009 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE - PROFILE METHOD - TERMS, DEFINITIONS AND SURFACE TEXTURE PARAMETERS |
NF EN ISO 13565-2 : 1998 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - SURFACES HAVING STRATIFIED FUNCTIONAL PROPERTIES - PART 2: HEIGHT CHARACTERIZATION USING THE LINEAR MATERIAL RATIO CURVE |
NF EN ISO 81714-1 : 2010 | DESIGN OF GRAPHICAL SYMBOLS FOR USE IN THE TECHNICAL DOCUMENTATION OF PRODUCTS - PART 1: BASIC RULES |
NFE 04 521 : 1986 | TECHNICAL DRAWINGS - GENERAL PRINCIPLES - LAYOUT OF DIMENSIONS AND PHYSICAL IMPLEMENTATION |
NF EN ISO 8785 : 1999 | GEOMETRICAL PRODUCT SPECIFICATION (GPS) - SURFACE IMPERFECTIONS - TERMS, DEFINITIONS AND PARAMETERS |
NF EN ISO 14660-1 : 1999 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GEOMETRICAL FEATURES - PART 1: GENERAL TERMS AND DEFINITIONS |
NF EN ISO 13565-3 : 2002 | GEOMETRICAL PRODUCT SPECIFICATION (GPS) - SURFACE TEXTURE: PROFILE METHOD - SURFACES HAVING STRATIFIED FUNCTIONAL PROPERTIES - PART 3: HEIGHT CHARACTERIZATION USING THE MATERIAL PROBABILITY CURVE |
NF EN ISO 12085 : 1998 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - MOTIF PARAMETERS |
NF EN ISO 1101 : 2017 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GEOMETRICAL TOLERANCING - TOLERANCES OF FORM, ORIENTATION, LOCATION AND RUN-OUT |
ISO 129-1:2004 | Technical drawings Indication of dimensions and tolerances Part 1: General principles |
NF EN ISO 3274 : 1998 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - NOMINAL CHARACTERISTICS OF CONTACT (STYLUS) INSTRUMENTS |
NF EN ISO 13565-1 : 1998 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - SURFACES HAVING STRATIFIED FUNCTIONAL PROPERTIES - PART 1: FILTERING AND GENERAL MEASUREMENT CONDITIONS |
NF EN ISO 11562 : 1998 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - METROLOGICAL CHARACTERISTICS OF PHASE CORRECT FILTERS |
NF EN ISO 4288 : 1998 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - RULES AND PROCEDURES FOR THE ASSESSMENT OF SURFACE TEXTURE |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.