PREN 14307 : DRAFT 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE EXTRUDED POLYSTYRENE FOAM (XPS) PRODUCTS - SPECIFICATION
01-12-2015
26-05-2015
Foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols, units and abbreviated terms
4 Requirements
5 Test methods
6 Designation code
7 Assessment and Verification of the Constancy of
Performance (AVCP)
8 Marking and labelling
Annex A (normative) - Factory production control
Annex B (normative) - Determination of the aged values of
thermal conductivity
Annex C (informative) - Additional properties
Annex ZA (informative) - Clauses of this European Standard
addressing the provisions of the EU Construction
Products Regulation
8 Declared performance
9 The performance of the product identified in points 1 and 2
is in conformity with the declared performance in point 8
This declaration of performance is issued under the sole
responsibility of the manufacturer identified in point 4.
Bibliography
Gives the requirements for factory made extruded polystyrene foam products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately - 180 degrees C to + 75 degrees C.
| Committee |
TC 88
|
| DocumentType |
Draft
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| 15/30315078 DC : DRAFT MAY 2015 | Identical |
| 05/30136538 DC : 0 | Identical |
| ISO 9229:2007 | Thermal insulation Vocabulary |
| EN 12667:2001 | Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Products of high and medium thermal resistance |
| ISO 13787:2003 | Thermal insulation products for building equipment and industrial installations Determination of declared thermal conductivity |
| EN 14706:2012 | Thermal insulating products for building equipment and industrial installations - Determination of maximum service temperature |
| EN 13468:2001 | Thermal insulating products for building equipment and industrial installations - Determination of trace quantities of water soluble chloride, fluoride, silicate, sodium ions and pH |
| EN 1607:2013 | Thermal insulating products for building applications - Determination of tensile strength perpendicular to faces |
| EN 1606:2013 | Thermal insulating products for building applications - Determination of compressive creep |
| EN 13471:2001 | Thermal insulating products for building equipment and industrial installations - Determination of the coefficient of thermal expansion |
| EN 12939:2000 | Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Thick products of high and medium thermal resistance |
| EN ISO 8497:1996 | Thermal insulation - Determination of steady-state thermal transmission properties of thermal insulation for circular pipes (ISO 8497:1994) |
| ISO 1716:2010 | Reaction to fire tests for products Determination of the gross heat of combustion (calorific value) |
| EN ISO 9229:2007 | Thermal insulation - Vocabulary (ISO 9229:2007) |
| EN 13164:2012+A1:2015 | Thermal insulation products for buildings - Factory made extruded polystyrene foam (XPS) products - Specification |
| EN ISO 4590:2016 | Rigid cellular plastics - Determination of the volume percentage of open cells and of closed cells (ISO 4590:2016) |
| EN 1605:2013 | Thermal insulating products for building applications - Determination of deformation under specified compressive load and temperature conditions |
| EN 824:2013 | Thermal insulating products for building applications - Determination of squareness |
| ISO 4590:2016 | Rigid cellular plastics Determination of the volume percentage of open cells and of closed cells |
| EN 12088:2013 | Thermal insulating products for building applications - Determination of long term water absorption by diffusion |
| ISO 11925-2:2010 | Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test |
| EN ISO 1182:2010 | Reaction to fire tests for products - Non-combustibility test (ISO 1182:2010) |
| EN 825:2013 | Thermal insulating products for building applications - Determination of flatness |
| EN 823:2013 | Thermal insulating products for building applications - Determination of thickness |
| ISO 8497:1994 | Thermal insulation — Determination of steady-state thermal transmission properties of thermal insulation for circular pipes |
| EN ISO 13787:2003 | Thermal insulation products for building equipment and industrial installations - Determination of declared thermal conductivity (ISO 13787:2003) |
| EN 13470:2001 | Thermal insulating products for building equipment and industrial installations - Determination of the apparent density of preformed pipe insulation |
| EN 13238:2010 | Reaction to fire tests for building products - Conditioning procedures and general rules for selection of substrates |
| ISO 1182:2010 | Reaction to fire tests for products Non-combustibility test |
| EN 13823:2010+A1:2014 | Reaction to fire tests for building products - Building products excluding floorings exposed to the thermal attack by a single burning item |
| EN 1602:2013 | Thermal insulating products for building applications - Determination of the apparent density |
| EN 12087:2013 | Thermal insulating products for building applications - Determination of long term water absorption by immersion |
| EN 13793:2003 | Thermal insulating products for building applications - Determination of behaviour under cyclic loading |
| EN 12090:2013 | Thermal insulating products for building applications - Determination of shear behaviour |
| EN 13472:2012 | Thermal insulating products for building equipment and industrial installations - Determination of short term water absorption by partial immersion of preformed pipe insulation |
| EN 1604:2013 | Thermal insulating products for building applications - Determination of dimensional stability under specified temperature and humidity conditions |
| EN 14707:2012 | Thermal insulating products for building equipment and industrial installations - Determination of maximum service temperature for preformed pipe insulation |
| EN 12091:2013 | Thermal insulating products for building applications - Determination of freeze-thaw resistance |
| EN 12089:2013 | Thermal insulating products for building applications - Determination of bending behaviour |
| ISO 10456:2007 | Building materials and products — Hygrothermal properties — Tabulated design values and procedures for determining declared and design thermal values |
| EN 1609:2013 | Thermal insulating products for building applications - Determination of short term water absorption by partial immersion |
| EN 826:2013 | Thermal insulating products for building applications - Determination of compression behaviour |
| EN ISO 1716:2010 | Reaction to fire tests for products - Determination of the gross heat of combustion (calorific value) (ISO 1716:2010) |
| EN 15715:2009 | Thermal insulation products - Instructions for mounting and fixing for reaction to fire testing - Factory made products |
| EN 12086:2013 | Thermal insulating products for building applications - Determination of water vapour transmission properties |
| EN 13172:2012 | Thermal insulation products - Evaluation of conformity |
| EN 822:2013 | Thermal insulating products for building applications - Determination of length and width |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.