SAE AS1946E
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Hose Assembly, Polytetrafluoroethylene, Metallic Reinforced, Up to 1500 psi and 450 °F, Hydraulic and Pneumatic
Available format(s)
Hardcopy , PDF
Superseded date
21-12-2018
Superseded by
Language(s)
English
Published date
16-06-2015
Publisher
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1. SCOPE
2. APPLICABLE DOCUMENTS
3. TECHNICAL REQUIREMENTS
4. QUALITY ASSURANCE PROVISIONS
5. PREPARATION FOR DELIVERY
6. NOTES
Describes the requirements for polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assemblies suitable for use in aerospace hydraulic, fuel and lubricating oil systems at temperatures between -67 degrees F and 450 degrees F for Class 1 assemblies, -67 degrees F and 275 degrees F for Class 2 assemblies, and at nominal pressures up to 1500 psi.
| DevelopmentNote |
Supplement 1 is available separately, see SAE AS 1946 SUP1. (09/2012)
|
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This SAE Aerospace Standard (AS) defines the requirements for polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assemblies suitable for use in aerospace hydraulic, fuel and lubricating oil systems at temperatures between −67 °F and 450 °F for Class I assemblies, −67 °F and 275 °F for Class II assemblies, and at nominal pressures up to 1500 psi. The hose assemblies are also suitable for use within the same temperature and pressure limitations in aerospace pneumatic systems where some gaseous diffusion through the wall of the PTFE liner can be tolerated.The use of these hose assemblies in pneumatic storage systems is not recommended. In addition, installations in which the limits specified herein are exceeded, or in which the application is not covered specifically by this standard, for example oxygen, shall be subject to the approval of the procuring activity.
| SAE AIR5693 | Compatibility of PTFE Hose Assemblies With Typical Fluids Found in Aerospace Applications |
| SAE AS150F | Hose Assembly, Type Classifications of, Basic Performance and Fire Resistance |
| MIL-DTL-25579 Revision H:2014 | Hose Assembly, Polytetrafluoroethylene, High Temperature, Medium Pressure, General Specification for |
| MIL-DTL-27267 Revision D:2012 | Hose, Cres Wire Reinforced, Polytetrafluoroethylene, Four Hundred Fifty Degree Fahrenheit, Medium Pressure |
| MIL-DTL-32434 Base Document:2013 | Hose Assembly, Polytetrafluoroethylene, Convoluted, High Temperature, Medium Pressure, General Specification for |
| MIL-DTL-52471 Revision F:2008 | HOSE AND HOSE ASSEMBLIES, RUBBER, HYDRAULIC PRESSURE TYPE, GENERAL SPECIFICATION FOR |
| SAE AS4897 | Hose Assembly, Polytetrafluoroethylene (PTFE), Low Pressure, 450 °F and Fireproof, Procurement Specification for |
| SAE AMS5689F | Steel, Corrosion and Heat Resistant, Wire 18Cr - 10.5Ni - 0.40Ti (SAE 30321) Solution Heat Treated |
| SAE AMS5659S | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Rings, and Extrusions 15Cr - 4.5Ni - 0.30Cb (Nb) - 3.5Cu |
| SAE AMS5645S | Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 18Cr - 10Ni - 0.40Ti (321) Solution Heat Treated |
| SAE ARP1835 | Preparation for Delivery, General Requirements for Hose Assemblies |
| SAE AS611E | Hose Assembly and Tubing, Polytetrafluoroethylene, Cleaning Methods for |
| ASTM A 262 : 2015 : REDLINE | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
| SAE AS644A | HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, METAL BRAID, MEDIUM PRESSURE, FLARED, 45° TO 90° |
| SAE AS642A | HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, METAL BRAID, MEDIUM PRESSURE, FLARED, STRAIGHT TO 90° |
| MIL-STD-130 Revision N:2007 | IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY |
| SAE AS640A | HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, METAL BRAID, MEDIUM PRESSURE, FLARED, STRAIGHT TO STRAIGHT |
| SAE AS641A | HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, METAL BRAID, MEDIUM PRESSURE, FLARED, STRAIGHT TO 45° |
| SAE AMS5581F | Nickel Alloy, Corrosion and Heat-Resistant, Seamless or Welded Tubing 62Ni - 21.5Cr - 9.0Mo - 3.7Cb (Nb) Annealed |
| NAS1760:2015 | FITTING END, FLARELESS ACORN, STANDARD DIMENSIONS FOR |
| MIL-PRF-7808 Revision L:1997 | LUBRICATING OIL, AIRCRAFT TURBINE ENGINE, SYNTHETIC BASE |
| SAE AS4209B | FITTING END ASSEMBLY, INTERNAL THREAD, RETAINED NUT, BEAM SEAL, DESIGN STANDARD |
| MIL-PRF-5606 Revision H:2002 | HYDRAULIC FLUID, PETROLEUM BASE; AIRCRAFT, MISSILE, AND ORDNANCE |
| SAE AMS5656F | Steel, Corrosion Resistant, Bars, Wire, Forgings, Extrusions, and Rings 9.0Mn - 20Cr - 6.5Ni - 0.27N Solution Heat Treated |
| SAE AMS5643U | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 16Cr - 4.0Ni - 0.30Cb (Nb) - 4.0Cu Solution Heat Treated, Precipitation Hardenable |
| SAE AS4395B | FITTING END, FLARED, TUBE CONNECTION, DESIGN STANDARD |
| SAE AMS5743J | Steel, Corrosion and Heat-Resistant, Bars and Forgings 15.5Cr - 4.5Ni - 2.9Mo - 0.10N Solution Heat Treated, Sub-Zero Cooled, Equalized, and Over-Tempered |
| SAE AS651C | HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, METAL BRAID, MEDIUM PRESSURE, FLARELESS, 45° TO 90° |
| SAE AMS5697F | Steel, Corrosion-Resistant, Wire 19Cr - 9.5Ni (SAE 30304) Solution Heat Treated |
| SAE AMS5690M | Steel, Corrosion and Heat Resistant, Wire 17Cr - 12Ni - 2.5Mo (316) Solution Heat Treated |
| SAE AMS5573L | Steel, Corrosion and Heat-Resistant, Seamless Tubing 17Cr - 12Ni - 2.5Mo (SAE 30316) Solution Heat Treated |
| SAE AMS5561G | Steel, Corrosion and Heat-Resistant, Welded and Drawn or Seamless and Drawn Tubing 9.0Mn - 20Cr - 6.5Ni - 0.28N High-Pressure Hydraulic |
| SAE AS1055D | Fire Testing of Flexible Hose, Tube Assemblies, Coils, Fittings, and Similar System Components |
| MIL-HDBK-831 Revision A:2013 | PREPARATION OF TEST REPORTS |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| SAE AS 85421/1 : 2002 | FITTING END, STANDARD DIMENSIONS FOR DYNAMIC BEAM SEAL, MALE |
| SAE AMS5647K | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 19Cr - 9.5Ni Solution Heat Treated |
| SAE AMS5648M | Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Tubing, and Rings, 17Cr - 12Ni - 2.5Mo (316) Solution Heat Treated |
| MIL-PRF-680 Revision C:2010 | DEGREASING SOLVENT |
| SAE AS647C | HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, METAL BRAID, MEDIUM PRESSURE, FLARELESS, STRAIGHT TO STRAIGHT |
| SAE AS648C | HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, METAL BRAID, MEDIUM PRESSURE, FLARELESS, STRAIGHT TO 45° |
| SAE ARP908C | Torque Requirements, Installation and Qualification Test, Hose and Tube Fitting |
| SAE AMS4965L | Titanium Alloy, Bars, Wire, Forgings, and Rings 6.0Al 4.0V Solution Heat Treated and Aged |
| SAE AMSQQP35 | Passivation Treatments for Corrosion-Resistant Steel |
| MIL-PRF-87257 Revision C:2017 | HYDRAULIC FLUID, FIRE RESISTANT, LOW TEMPERATURE, SYNTHETIC HYDROCARBON BASE, AIRCRAFT AND MISSILE |
| SAE AS7003D | Nadcap Program Requirements |
| ASME Y14.24 : 2012 | TYPES AND APPLICATIONS OF ENGINEERING DRAWINGS - ENGINEERING DRAWING AND RELATED DOCUMENTATION PRACTICES |
| SAE AS7112 | NATIONAL AEROSPACE AND DEFENSE CONTRACTORS ACCREDITATION PROGRAM REQUIREMENTS FOR FLUID SYSTEM COMPONENTS |
| SAE AMS5567F | Steel, Corrosion Resistant, Seamless or Welded Hydraulic Tubing 19Cr - 10Ni (304) Solution Heat Treated |
| SAE AMS5646P | Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Tubing, and Rings 18Cr - 11Ni - 0.60Cb(Nb) (347) Solution Heat Treated |
| SAE AS85421A | Fittings, Tube, Fluid Systems, Separable, Beam Seal, 3000/4000 psi, General Specification For |
| SAE AS649C | HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, METAL BRAID, MEDIUM PRESSURE, FLARELESS, STRAIGHT TO 90° |
| SAE AMS4945F | Titanium Alloy Tubing, Seamless, Hydraulic 3Al - 2.5V, Controlled Contractile Strain Ratio Cold Worked, Stress Relieved |
| SAE AS 8879 : 2004 | SCREW THREADS - UNJ PROFILE, INCH CONTROLLED RADIUS ROOT WITH INCREASED MINOR DIAMETER |
| SAE AS1072F | Sleeve, Hose Assembly, Fire Protection |
| MIL A 8625 : F | ANODIC COATINGS FOR ALUMINUM AND ALUMINUM ALLOYS |
| SAE AMS4117K | Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire and Flash Welded Rings 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061; -T6, -T651) |
| SAE AMS4127J | Aluminum Alloy, Forgings and Rolled or Forged Rings (6061-T6) Solution and Precipitation Heat Treated |
| SAE AS643A | HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, METAL BRAID, MEDIUM PRESSURE, FLARED, 45° TO 45° |
| SAE AS2078A | Test Methods, Hose Assemblies, Polytetrafluoroethylene (PTFE) |
| SAE AMS4069F | Aluminum Alloy, Drawn, Round Seamless Tubing Close Tolerance 2.5Mg - 0.25Cr (5052-O) Annealed |
| MIL-PRF-83282 Revision D:1997 | HYDRAULIC FLUID, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE, METRIC, NATO CODE NUMBER H-537 |
| SAE AS645A | HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, METAL BRAID, MEDIUM PRESSURE, FLARED, 90° TO 90° |
| SAE AMS5639J | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 19Cr - 10Ni Solution Heat Treated |
| SAE AMS4944L | Titanium Alloy Tubing, Seamless, Hydraulic 3.0Al - 2.5V Cold Worked, Stress Relieved |
| SAE AS33514C | FITTING END, STANDARD DIMENSIONS FOR FLARELESS TUBE CONNECTION AND GASKET SEAL |
| SAE AMS4082P | Aluminum Alloy, Seamless Drawn Tubing 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T6) Solution and Precipitation Heat Treated |
| SAE AS4375C | FITTING END, FLARELESS, DESIGN STANDARD |
| SAE AS150E | Hose Assembly, Type Classifications of, Basic Performance and Fire Resistance |
| SAE AMS4339A | Aluminum Alloy, Rolled or Cold Finished Bars and Rods 4.4Cu - 1.5Mg - 0.60Mn (2024-T851) Solution Heat Treated, Cold Worked, and Artificially Aged |
| SAE AMS5644E | Steel, Bars and Forgings, Corrosion Resistant 17Cr - 7Ni - 1Al |
| SAE AS4006 | HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, PTFE, METAL BRAID, MEDIUM PRESSURE, BEAM SEAL, STRAIGHT TO STRAIGHT |
| ASME Y14.100 : 2017 | ENGINEERING DRAWING PRACTICES - ENGINEERING DRAWING AND RELATED DOCUMENTATION PRACTICES |
| SAE AS652C | HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, METAL BRAID, MEDIUM PRESSURE, FLARELESS, 90° TO 90° |
| ASTM D 471 : 2016-02 | TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS |
| SAE AMS5653H | Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Tubing, and Rings 17Cr - 12Ni - 2.5Mo (0.030 Max C) (316L) Solution Heat Treated |
| SAE AMS5666H | Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, Extrusions, and Rings 62Ni - 21.5Cr - 9.0Mo - 3.65Cb (Nb) Annealed |
| SAE AS650C | HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, METAL BRAID, MEDIUM PRESSURE, FLARELESS, 45° TO 45° |
| SAE AMS5556J | Steel, Corrosion and Heat-Resistant, Seamless or Welded Hydraulic Tubing 18Cr - 11Ni - 0.70Cb (347) Solution Heat Treated |
| SAE AMS4121J | Aluminum Alloy Bars, Rods, and Wire, Rolled, Drawn, or Cold Finished 4.5Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-T6, -T651) Solution and Precipitation Heat Treated |
| SAE AMS4928V | Titanium Alloy Bars, Wire, Forgings, Rings, and Drawn Shapes 6Al - 4V Annealed |
| NAS847:2012 | CAPS AND PLUGS, PROTECTIVE, DUST AND MOISTURE SEAL |
| SAE AMS5565L | Steel, Corrosion Resistant, Welded Tubing 19Cr - 9.5Ni (304) Solution Heat Treated |
| SAE AMS5557J | Steel, Corrosion and Heat-Resistant, Seamless or Welded Hydraulic Tubing 18.5Cr - 10.5Ni - 0.40Ti (SAE 30321) Solution Heat Treated |
| SAE AS4207A | FITTING END, EXTERNAL THREAD, BEAM SEAL, DESIGN STANDARD |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.