SAE J 517 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
HYDRAULIC HOSE
Hardcopy , PDF
20-07-2020
English
01-01-2017
1 SCOPE
2 REFERENCES
3 DEFINITIONS
4 AGE CONTROL
5 HOSE CONNECTORS
6 HOSE ASSEMBLIES
7 HOSE CUT END ANGLE DIMENSION
8 APPLICATION FACTORS
9 SIZE DESIGNATIONS
10 HOSE IDENTIFICATION
11 ORIENTATION OF OFFSET ELBOW ENDS IN A
HOSE ASSEMBLY
12 ASSEMBLY LENGTH
13 TESTS
14 INSPECTION RETESTS AND REJECTION
15 ORDERING INFORMATION (FOR DOD
PROCUREMENT ONLY)
16 ONE STEEL WIRE BRAID REINFORCED, RUBBER
COVERED HYDRAULIC HOSE (SAE 100R1)
17 TWO STEEL WIRE BRAID REINFORCED, RUBBER
COVERED HYDRAULIC HOSE (SAE 100R2)
18 DOUBLE FIBER BRAID (NONMETALLIC),
RUBBER COVERED HYDRAULIC HOSE (SAE 100R3)
19 WIRE INSERTED HYDRAULIC SUCTION HOSE (SAE 100R4)
20 SINGLE WIRE BRAID, TEXTILE COVERED
HYDRAULIC HOSE (SAE 100R5)
21 FIBER REINFORCED (NONMETALLIC), RUBBER
COVERED HYDRAULIC HOSE (SAE 100R6)
22 THERMOPLASTIC HYDRAULIC HOSE (SAE 100R7)
23 HIGH PRESSURE THERMOPLASTIC HYDRAULIC
HOSE (SAE 100R8)
24 FOUR SPIRAL STEEL WIRE REINFORCED,
RUBBER COVERED HYDRAULIC HOSE (SAE 100R12)
25 MULTIPLE SPIRAL STEEL WIRE REINFORCED,
RUBBER COVERED HYDRAULIC HOSE (SAE 100R13)
26 PTFE LINED HYDRAULIC HOSE (SAE 100R14)
27 MULTIPLE SPIRAL STEEL WIRE REINFORCED,
RUBBER COVERED HYDRAULIC HOSE (SAE 100R15)
28 COMPACT, ONE AND TWO STEEL WIRE BRAID
REINFORCED, RUBBER COVERED HYDRAULIC HOSE (SAE 100R16)
29 COMPACT, 21 MPa MAXIMUM WORKING
PRESSURE, ONE AND TWO STEEL WIRE REINFORCED,
RUBBER COVERED HYDRAULIC HOSE (SAE 100R17)
30 21 MPa THERMOPLASTIC HYDRAULIC HOSE (SAE 100R18)
31 COMPACT, 28 MPA MAXIMUM WORKING
PRESSURE, ONE AND TWO STEEL WIRE REINFORCED,
RUBBER COVERED HYDRAULIC HOSE (SAE 100R19)
32 NOTES
Specifies general, dimensional and performance specifications for the most common hoses used in hydraulic systems on mobile and stationary equipment.
DevelopmentNote |
Supersedes A A 52413. (07/2003) Supersedes MIL H 52471/6 (A). (12/2008)
|
DocumentType |
Standard
|
Pages |
38
|
PublisherName |
SAE International
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
ISO 3862:2017 | Rubber hoses and hose assemblies Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids Specification |
SAE J 846 : 2015 | CODING SYSTEMS FOR IDENTIFICATION OF FLUID CONDUCTORS AND CONNECTORS |
SAE J 518 : 2013 | HYDRAULIC FLANGED TUBE, PIPE, AND HOSE CONNECTIONS, FOUR-BOLT SPLIT FLANGE TYPE |
SAE J 1475 : 2014 | HYDRAULIC HOSE FITTING FOR MARINE APPLICATIONS |
ISO 3949:2009 | Plastics hoses and hose assemblies Textile-reinforced types for hydraulic applications Specification |
SAE J 1401 : 2013 | ROAD VEHICLE - HYDRAULIC BRAKE HOSE ASSEMBLIES FOR USE WITH NONPETROLEUM-BASE HYDRAULIC FLUIDS |
MIL-PRF-7808 Revision L:1997 | LUBRICATING OIL, AIRCRAFT TURBINE ENGINE, SYNTHETIC BASE |
SAE J 516 : 2016 | HYDRAULIC HOSE FITTINGS |
ISO 4397:2011 | Fluid power connectors and associated components — Nominal outside diameters of tubes and nominal hose sizes |
ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
SAE J 1273 : 2014 | RECOMMENDED PRACTICES FOR HYDRAULIC HOSE ASSEMBLIES |
SAE J 343 : 2016 | TEST AND TEST PROCEDURES FOR SAE 100R SERIES HYDRAULIC HOSE AND HOSE ASSEMBLIES |
ISO 4079:2017 | Rubber hoses and hose assemblies Textile-reinforced hydraulic types for oil-based or water-based fluids Specification |
SAE J 1453/1 : 2012 | SPECIFICATION FOR O-RING FACE SEAL CONNECTORS - PART 1: TUBE CONNECTION DETAILS AND COMMON REQUIREMENTS FOR PERFORMANCE AND TESTS |
ISO 11237:2017 | Rubber hoses and hose assemblies — Compact wire-braid-reinforced hydraulic types for oil-based or water-based fluids — Specification |
SAE J 1942/1 : 2016 | QUALIFIED HOSES FOR MARINE APPLICATIONS |
MIL-PRF-83282 Revision D:1997 | HYDRAULIC FLUID, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE, METRIC, NATO CODE NUMBER H-537 |
SAE J 1942 : 2014 | HOSE AND HOSE ASSEMBLIES FOR MARINE APPLICATIONS |
SAE J 1927 : 2014 | CUMULATIVE DAMAGE ANALYSIS FOR HYDRAULIC HOSE ASSEMBLIES |
ISO 4671:2007 | Rubber and plastics hoses and hose assemblies Methods of measurement of the dimensions of hoses and the lengths of hose assemblies |
ISO 1402:2009 | Rubber and plastics hoses and hose assemblies Hydrostatic testing |
SAE J 1176 : 2012 | EXTERNAL LEAKAGE CLASSIFICATIONS FOR HYDRAULIC SYSTEMS |
ISO 6803:2017 | Rubber or plastics hoses and hose assemblies — Hydraulic-pressure impulse test without flexing |
MIL H 8446 : LATEST | HYDRAULIC FLUID, NONPETROLEUM BASE, AIRCRAFT |
ISO 1436:2017 | Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types for oil-based or water-based fluids Specification |
ASTM D 471 : 2016-02 | TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS |
FED-STD-595 Revision C:2008 | COLORS USED IN GOVERNMENT PROCUREMENT |
ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.