SAE J1926/2_201609
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Connections for General Use and Fluid Power - Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing - Part 2: Heavy-Duty (S Series) Stud Ends
Hardcopy , PDF
09-03-2023
English
09-09-2016
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
1. SCOPE
2. REFERENCES
3. DEFINITIONS
4. STUD END
5. REQUIREMENTS
6. O-RING
7. IDENTIFICATION STATEMENT
8. NOTES
APPENDIX A - ASSEMBLY INSTRUCTIONS FOR ADJUSTABLE STYLE
FITTINGS IN STRAIGHT THREAD O-RING PORT
APPENDIX B - OPTIONAL INCH HEX SIZES AND DIMENSIONS NOT TO
BE USED FOR NEW DESIGN
Describes dimensions, performance requirements, and test procedures for adjustable and nonadjustable heavy-duty (S series) stud ends with ASME B1.1 threads for use in fluid power and general applications and the O-rings used with them that are currently not listed in SAE J515.
| DocumentType |
Standard
|
| Pages |
15
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This part of SAE J1926 specifies dimensions, performance requirements, and test procedures for adjustable and nonadjustable heavy-duty (S series) stud ends with ASME B1.1 threads for use in fluid power and general applications and the O-rings used with them that are currently not listed in SAE J515.Stud ends in accordance with this part of SAE J1926 may be used at working pressures up to 63 MPa for nonadjustable stud ends and up to 41.3 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc.For threaded ports and stud ends specified in new designs for hydraulic fluid power applications, only ISO 6149 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new design in hydraulic fluid power applications.Conformance to the dimensional information does not guarantee rated performance. Each manufacturer shall perform testing according to the specification contained in this document to ensure that components made to this document comply with the performance rating.Appendices A and B of this document are informative.
| SAE J2551/2_201302 | Recommended Practices for Fluid Conductor Carbon, Alloy and High Strength Low Alloy Steel Tubing Applications-Part 2: General Specifications and Performance Requirements |
| SAE J846_201511 | Coding Systems for Identification of Fluid Conductors and Connectors |
| SAE J1298_201704 | Connections for Fluid Power and General Use - Hydraulic Couplings - Diagnostic Port Sizes and Locations |
| SAE J1502_201305 | Connections for Fluid Power and General Use - Hydraulic Couplings - Diagnostic |
| SAE J2593_201502 | Information Report for the Installation of Fluid Conductors and Connectors |
| SAE J2551/3_201302 | Recommended Practices for Fluid Conductor Carbon, Alloy and High Strength Low Alloy Steel Tubing Applications - Part 3: Procurement |
| SAE J1453/3_201206 | Specification for O-Ring Face Seal Connectors: Part 3 - Requirements, Dimensions, and Tests for Steel Unions, Bulkheads, Swivels, Braze Sleeves, Caps, and Connectors with SAE J1926-2 Inch Stud Ends |
| SAE J515_201511 | Specification for O-Ring Materials Used with Hydraulic Connectors |
| SAE J1926/1_201609 | Connections for General Use and Fluid Power - Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing - Part 1: Threaded Port with O-Ring Seal in Truncated Housing |
| SAE J2551/1_201302 | Recommended Practices for Fluid Conductor Carbon, Alloy and High Strength Low Alloy Steel Tubing Applications-Part 1: Design and Fabrication |
| SAE J1453/1_201205 | Specification for O-Ring Face Seal Connectors: Part 1 - Tube Connection Details and Common Requirements for Performance and Tests |
| SAE J2551_201309 | Recommended Practices for Fluid Conductor Carbon and Alloy Steel Tubing Applications |
| SAE J1926/3_201609 | Connections for General Use and Fluid Power - Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing - Part 3: Light-Duty (L-Series) Stud Ends |
| MIL-DTL-17849 Revision F:2018 | Strainers, Sediment, Pipeline, Duplex (with and without Magnet) |
| SAE J516_201604 | Hydraulic Hose Fittings |
| MIL-STD-2193 Revision C:2012 | Ship Hydraulic System Components |
| ISO 11926-2:1995 | Connections for general use and fluid power — Ports and stud ends with ISO 725 threads and O-ring sealing — Part 2: Heavy-duty (S series) stud ends |
| ISO 1179-1:2013 | Connections for general use and fluid power — Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing — Part 1: Threaded ports |
| SAE J1926/4_201008 | Connector for Fluid Power and General Use—Ports and Stud End with ASME B1.1 Threads and O-Ring Seal—Part 4: External Hex and Internal Hex Inch Port Plugs—Dimensions, Design, Test Methods and Requirements |
| SAE J1926/3_201609 | Connections for General Use and Fluid Power - Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing - Part 3: Light-Duty (L-Series) Stud Ends |
| ISO 5598:2008 | Fluid power systems and components Vocabulary |
| ISO 4759-1:2000 | Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| ISO 9974-1:1996 | Connections for general use and fluid power Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Part 1: Threaded ports |
| ISO 9974-3:1996 | Connections for general use and fluid power — Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing — Part 3: Stud ends with metal-to-metal sealing (type B) |
| ISO 9974-2:1996 | Connections for general use and fluid power — Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing — Part 2: Stud ends with elastomeric sealing (type E) |
| SAE J1926/1_201609 | Connections for General Use and Fluid Power - Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing - Part 1: Threaded Port with O-Ring Seal in Truncated Housing |
| ISO 1179-4:2007 | Connections for general use and fluid power Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 4: Stud ends for general use only with metal-to-metal sealing (type B) |
| SAE J1453/3_201206 | Specification for O-Ring Face Seal Connectors: Part 3 - Requirements, Dimensions, and Tests for Steel Unions, Bulkheads, Swivels, Braze Sleeves, Caps, and Connectors with SAE J1926-2 Inch Stud Ends |
| ISO 6149-3:2006 | Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 3: Dimensions, design, test methods and requirements for light-duty (L series) stud ends |
| SAE J2593_201502 | Information Report for the Installation of Fluid Conductors and Connectors |
| ISO 1302:2002 | Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation |
| SAE J515_201511 | Specification for O-Ring Materials Used with Hydraulic Connectors |
| ISO 19879:2010 | Metallic tube connections for fluid power and general use Test methods for hydraulic fluid power connections |
| ISO 6149-2:2006 | Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 2: Dimensions, design, test methods and requirements for heavy-duty (S series) stud ends |
| ISO 6149-1:2006 | Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 1: Ports with truncated housing for O-ring seal |
| ISO 48:2010 | Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) |
| ISO 1179-2:2013 | Connections for general use and fluid power — Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing — Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) |
| ISO 1179-3:2007 | Connections for general use and fluid power Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 3: Light-duty (L series) stud ends with sealing by O-ring with retaining ring (types G and H) |
| ISO 6410-1:1993 | Technical drawings — Screw threads and threaded parts — Part 1: General conventions |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.