SAE J2698_201411
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Primary Single Phase Nominal 120 VAC Wiring Distribution Assembly Design—Truck and Bus
Hardcopy , PDF
10-08-2020
English
24-11-2014
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1. SCOPE
2. REFERENCES
3. DEFINITIONS
4. WIRING
5. TERMINAL AND CONNECTION FUNCTION
(NON-SUPPLY POINT)
6. SUPPLY CONNECTIONS
7. RECEPTACLES
8. OVERCURRENT AND FAULT PROTECTION
9. SWITCHES AND CONTROLS
10. GROUNDING AND BONDING
11. COMPONENT/SYSTEM TESTING AND APPROVAL
12. WIRING CIRCUIT INSTALLATION AND PROTECTION
13. MARKINGS
14. INSTRUCTION MANUAL
15. SEPARATION OF CIRCUITS
16. VOLTAGE DROP
Describes the design and application of primary on-board wiring distribution system harnessing for surface vehicles.
| DocumentType |
Standard
|
| Pages |
10
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This SAE Recommended Practice covers the design and application of primary on-board wiring distribution system harnessing for surface vehicles. This document is intended for single phase nominal 120 VAC circuits that provide power to truck sleeper cab hotel loads so that they may operate with the main propulsion engine turned off. The power supply comes from alternative sources such as land-based grid power, DC-AC inverters and auxiliary power generators. The circuits may also provide power to improve vehicle performance through charging batteries or operating cold-weather starting aids.
| SAE J2697_201702 | Inverter Requirements for Class Eight Trucks - Truck and Bus |
| SAE J2891_201512 | Auxiliary Power Unit Electrical Interface Requirements for Class Eight Trucks |
| UL 514A:11ED 2013-02-01 | Metallic Outlet Boxes |
| UL 50:13ED 2015-10-16 | Enclosures for Electrical Equipment, Non-Environmental Considerations |
| CSA C22.2 No. 5 : 2013 | MOLDED-CASE CIRCUIT BREAKERS, MOLDED-CASE SWITCHES AND CIRCUIT-BREAKER ENCLOSURES |
| CSA C22.2 No. 49 : 2014 | FLEXIBLE CORDS AND CABLES |
| SAE J560_201604 | Primary and Auxiliary Seven Conductor Electrical Connector for Truck-Trailer Jumper Cable |
| CSA C22.2 No. 0.4 : 2004(R2013) | BONDING OF ELECTRICAL EQUIPMENT |
| CSA C22.2 No. 21 : 2014 | CORD SETS AND POWER-SUPPLY CORDS |
| UL 83:16ED 2017-07-28 | Standard for Thermoplastic-Insulated Wires and Cables |
| CSA C22.2 No. 144 : 1991 | GROUND FAULT CIRCUIT INTERRUPTERS |
| SAE J1673_201203 | High Voltage Automotive Wiring Assembly Design |
| SAE J447_201604 | Prevention of Corrosion of Motor Vehicle Body and Chassis Components |
| UL 943:5ED 2016-05-17 | Ground-Fault Circuit-Interrupters |
| SAE J1128_201512 | Low Voltage Primary Cable |
| UL 514C:4ED 2014-04-08 | Nonmetallic Outlet Boxes, Flush-Device Boxes, and Covers |
| SAE J1455_201703 | Recommended Environmental Practices for Electronic Equipment Design in Heavy-Duty Vehicle Applications |
| SAE J1908_201302 | Electrical Grounding Practice |
| CSA C22.2 No. 65 : 2013 | WIRE CONNECTORS |
| NEMA WD 6 : 2016 | WIRING DEVICES - DIMENSIONAL SPECIFICATIONS |
| SAE J2223/2_201102 | Connections for On-Board Road Vehicle Electrical Wiring Harnesses—Part 2: Tests and General Performance Requirements |
| CSA C22.2 No. 18 : 0 | OUTLET BOXES, CONDUIT BOXES, FITTINGS AND ASSOCIATED HARDWARE |
| NFPA 70 : 2017 | NATIONAL ELECTRICAL CODE |
| SAE J1654_201609 | Unshielded High Voltage Primary Cable |
| C22.2 NO. 75-17 | Thermoplastic insulated wires and cables (Trinational standard with UL 83 and NMX-J-010-ANCE-2017) |
| SAE J1742_201003 | Connections for High Voltage On-Board Vehicle Electrical Wiring Harnesses - Test Methods and General Performance Requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.