SAE J526_201611
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Welded Low-Carbon Steel Tubing Suitable for Bending, Flaring, Beading, Forming and Brazing
Hardcopy , PDF
12-09-2022
English
18-11-2016
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1. SCOPE
2. REFERENCES
3. MANUFACTURE
4. DIMENSIONS AND TOLERANCES
5. MANUFACTURING STANDARDS
6. MATERIAL
7. MECHANICAL PROPERTIES
8. PERFORMANCE REQUIREMENTS
9. TEST CERTIFICATES
10. CLEANLINESS
11. CORROSION PROTECTION
12. PACKAGING
13. NOTES
Specifies electric-resistance welded single-wall low-carbon steel pressure tubing intended for general automotive, refrigeration, hydraulic, and other similar applications requiring tubing of a quality suitable for bending, flaring, beading, forming, and brazing.
| DocumentType |
Standard
|
| Pages |
6
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
The SAE J526 Standard covers electric-resistance welded single-wall low-carbon steel pressure tubing intended for general automotive, refrigeration, hydraulic, and other similar applications requiring tubing of a quality suitable for bending, flaring, beading, forming, and brazing. Material produced to this specification is not intended to be used for single flare applications due to the potential leak path that would be caused by the ID weld bead or scarfed region. Assumption of risks when using this material for single flare applications shall be defined by agreement between the producer and tube purchaser. The material produced to this specification is intended to service pressure applications where severe forming and bending is not required. As this material may exhibit mechanical properties that reduce some desired forming characteristics versus SAE J356, the severity of the forming requirements of the finished assembly should be considered when utilizing material produced to this specification.
| SAE J2551/2_201302 | Recommended Practices for Fluid Conductor Carbon, Alloy and High Strength Low Alloy Steel Tubing Applications-Part 2: General Specifications and Performance Requirements |
| SAE J533_201702 | Flares for Tubing |
| SAE J2593_201502 | Information Report for the Installation of Fluid Conductors and Connectors |
| SAE J1065_201605 | Nominal Reference Working Pressures for Steel Hydraulic Tubing |
| MIL H 13719 : D | HOSE ASSEMBLY, RUBBER, HYDRAULIC BRAKE |
| ASTM F 2793 : 2014 | Standard Specification for Bicycle Grips |
| ANSI/CSA NGV 5.1-2016 (R2020) | Residential fueling appliances |
| CSA NGV 5.1 : 2016 | RESIDENTIAL FUELING APPLIANCES |
| SAE J2592_201305 | Carbon Steel Tubing for General Use - Understanding Nondestructive Testing for Carbon Steel Tubing |
| SAE J2551/1_201302 | Recommended Practices for Fluid Conductor Carbon, Alloy and High Strength Low Alloy Steel Tubing Applications-Part 1: Design and Fabrication |
| SAE J2551_201309 | Recommended Practices for Fluid Conductor Carbon and Alloy Steel Tubing Applications |
| SAE J2551/3_201302 | Recommended Practices for Fluid Conductor Carbon, Alloy and High Strength Low Alloy Steel Tubing Applications - Part 3: Procurement |
| SAE J1677_201612 | Tests and Procedures for Carbon Steel and High Strength Low Alloy Steel Tubing |
| SAE J2045_201211 | Performance Requirements for Fuel System Tubing Assemblies |
| CSA/ANSI NGV 5.2-2017 | Vehicle fueling appliances (VFA) |
| EN 10305-3:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 3: Welded cold sized tubes |
| ISO 5598:2008 | Fluid power systems and components Vocabulary |
| SAE J516_201604 | Hydraulic Hose Fittings |
| ISO 10583:1993 | Aerospace fluid systems — Test methods for tube/fitting assemblies |
| SAE J1290_201207 | Automotive Hydraulic Brake System - Metric Tube Connections |
| SAE J2551/1_201302 | Recommended Practices for Fluid Conductor Carbon, Alloy and High Strength Low Alloy Steel Tubing Applications-Part 1: Design and Fabrication |
| SAE J403_201406 | Chemical Compositions of SAE Carbon Steels |
| SAE J409_199502 | PRODUCT ANALYSIS—PERMISSIBLE VARIATIONS FROM SPECIFIED CHEMICAL ANALYSIS OF A HEAT OR CAST OF STEEL |
| SAE J1453/2_201504 | Specification for O-Ring Face Seal Connectors: Part 2 - Requirements, Dimensions, and Tests for Steel Unions, Bulkheads, Swivels, Braze Sleeves, Braze-on Tube Ends, Caps, and Connectors with ISO 6149-2 Metric Stud Ends and ISO 6162 4-Bolt Flange Heads |
| ISO 3305:1985 | Plain end welded precision steel tubes — Technical conditions for delivery |
| SAE J1065_201605 | Nominal Reference Working Pressures for Steel Hydraulic Tubing |
| SAE J356_201312 | Welded Flash-Controlled Low-Carbon Steel Tubing Normalized for Bending, Double Flaring, and Beading |
| ISO 8434-2:2007 | Metallic tube connections for fluid power and general use — Part 2: 37 degree flared connectors |
| SAE J1453/3_201206 | Specification for O-Ring Face Seal Connectors: Part 3 - Requirements, Dimensions, and Tests for Steel Unions, Bulkheads, Swivels, Braze Sleeves, Caps, and Connectors with SAE J1926-2 Inch Stud Ends |
| SAE J1453/1_201205 | Specification for O-Ring Face Seal Connectors: Part 1 - Tube Connection Details and Common Requirements for Performance and Tests |
| ISO 8434-3:2005 | Metallic tube connections for fluid power and general use — Part 3: O-ring face seal connectors |
| ISO 19879:2010 | Metallic tube connections for fluid power and general use Test methods for hydraulic fluid power connections |
| SAE J514_201201 | Hydraulic Tube Fittings |
| SAE J1677_201612 | Tests and Procedures for Carbon Steel and High Strength Low Alloy Steel Tubing |
| ISO 10763:1994 | Hydraulic fluid power Plain-end, seamless and welded precision steel tubes Dimensions and nominal working pressures |
| SAE J533_201702 | Flares for Tubing |
| SAE J2551/2_201302 | Recommended Practices for Fluid Conductor Carbon, Alloy and High Strength Low Alloy Steel Tubing Applications-Part 2: General Specifications and Performance Requirements |
| SAE J2551/3_201302 | Recommended Practices for Fluid Conductor Carbon, Alloy and High Strength Low Alloy Steel Tubing Applications - Part 3: Procurement |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.