SSPC-CS 23.00 : 2016
Current
The latest, up-to-date edition.
SPECIFICATION FOR THE APPLICATION OF THERMAL SPRAY COATINGS (METALLIZING) OF ALUMINUM, ZINC, AND THEIR ALLOYS AND COMPOSITES FOR THE CORROSION PROTECTION OF STEEL
Hardcopy , PDF
English
08-09-2016
FOREWORD
SECTION 1 - INTRODUCTION
SECTION 2 - DEFINITIONS
SECTION 3 - SUMMARY OF PRACTICE
SECTION 4 - TSC FEEDSTOCK REQUIREMENTS
SECTION 5 - SURFACE PREPARATION REQUIREMENTS
SECTION 6 - THERMAL SPRAY EQUIPMENT SETUP
SECTION 7 - JOB REFERENCE STANDARD (JRS)
SECTION 8 - TSC APPLICATION PROCEDURE
SECTION 9 - INSPECTION OF APPLIED TSC
SECTION 10 - APPLICATION OF OPTIONAL SEALERS AND TOPCOATS
SECTION 11 - RECORDS
SECTION 12 - DEBRIS CONTAINMENT AND CONTROL
SECTION 13 - WORK PROCEDURES AND SAFETY
SECTION 14 - APPLICATION PROCEDURE
REFERENCES
BIBLIOGRAPHY
APPENDIX A - BEND TEST (NONMANDATORY)
APPENDIX B - HAMMER AND CHISEL CUT TEST (NONMANDATORY)
APPENDIX C - COMMENTARY (NONMANDATORY)
APPENDIX D - WET-DOWN EARLY RUST TEST (NONMANDATORY)
Describes requirements for surface preparation, coating application, repair of coating defects, measurement of coating thickness, adhesion testing of the applied coating, and application of sealers and topcoats over the thermally sprayed metal coating.
DevelopmentNote |
Jointly published by NACE, AWS and SSPC. Also numbered as AWS C2.23M/C2.23 & NACE 12. (09/2016)
|
DocumentType |
Standard
|
Pages |
12
|
PublisherName |
The Society for Protective Coatings
|
Status |
Current
|
Supersedes |
ISO 21809-3:2016 | Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 3: Field joint coatings |
API SPEC 16F : 2017 | SPECIFICATION FOR MARINE DRILLING RISER EQUIPMENT |
BS EN ISO 21809-3:2016 | Petroleum and natural gas industries. External coatings for buried or submerged pipelines used in pipeline transportation systems Field joint coatings |
EN ISO 21809-3:2016 | Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 3: Field joint coatings (ISO 21809-3:2016) |
I.S. EN ISO 21809-3:2016 | PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 3: FIELD JOINT COATINGS (ISO 21809-3:2016) |
14/30300605 DC : 0 | BS EN ISO 21809-3 - PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 3: FIELD JOINT COATINGS |
UNE-EN ISO 21809-3:2016 | Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 3: Field joint coatings (ISO 21809-3:2016) |
NACE 30105 : 0 | ELECTRICAL ISOLATION/CONTINUITY AND COATING ISSUES FOR OFFSHORE PIPELINE CATHODIC PROTECTION SYSTEMS |
BS 5493:1977 | Code of practice for protective coating of iron and steel structures against corrosion |
NACE WJ 3 : 2012 | WATERJET CLEANING OF METALS - THOROUGH CLEANING |
ASTM B 833 : 2013 : REDLINE | Standard Specification for Zinc and Zinc Alloy Wire for Thermal Spraying (Metallizing) for the Corrosion Protection of Steel |
NFPA 58 : 2017 | LIQUEFIED PETROLEUM GAS CODE |
NACE SP 01 78 : 2007 | DESIGN, FABRICATION, AND SURFACE FINISH PRACTICES FOR TANKS AND VESSELS TO BE LINED FOR IMMERSION SERVICE |
NACE WJ 2 : 2012 | WATERJET CLEANING OF METALS - VERY THOROUGH CLEANING |
CFR 29(PTS1900-1910) : 0 | LABOR - OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR |
ASTM D 4541 : 2017 : REDLINE | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
ASTM D 4417 : 2014 : REDLINE | Standard Test Methods for Field Measurement of Surface Profile of Blast Cleaned Steel |
SSPC-SP WJ 4 : 2012 | WATERJET CLEANING OF METALS - LIGHT CLEANING |
ASTM D 4285 : 1983 : R2018 | Standard Test Method for Indicating Oil or Water in Compressed Air |
SSPC-SP WJ 2 : 2012 | WATERJET CLEANING OF METALS - VERY THOROUGH CLEANING |
NACE WJ 1 : 2012 | WATERJET CLEANING OF METALS - CLEAN TO BARE SUBSTRATE |
IEEE/ASTM SI_10-2010 | American National Standard for Metric Practice |
AWS C2.14 : 1974 | CORROSION TESTS OF FLAME SPRAYED COATED STEEL, 19-YEAR REPORT, |
SSPC-SP WJ 1 : 2012 | WATERJET CLEANING OF METALS - CLEAN TO BARE SUBSTRATE |
SSPC-SP WJ 3 : 2012 | WATERJET CLEANING OF METALS - THOROUGH CLEANING |
SSPC-GUIDE 15 : 2013 | FIELD METHODS FOR EXTRACTION AND ANALYSIS OF SOLUBLE SALTS ON STEEL AND OTHER NONPOROUS SUBSTRATES |
SSPC-PA 17 : 2012 | PROCEDURE FOR DETERMINING CONFORMANCE TO STEEL PROFILE/SURFACE ROUGHNESS/PEAK COUNT REQUIREMENTS |
SSPC-AB 1 : 2015 | MINERAL AND SLAG ABRASIVES |
AWS C2.25/C2.25M : 2012 | SPECIFICATION FOR THERMAL SPRAY FEEDSTOCK - WIRE AND RODS |
ASTM E 337 : 2015 : REDLINE | Standard Test Method for Measuring Humidity with a Psychrometer (the Measurement of Wet- and Dry-Bulb Temperatures) |
NACE WJ 4 : 2012 | WATERJET CLEANING OF METALS - LIGHT CLEANING |
SSPC-AB 2 : 2015 | CLEANLINESS OF RECYCLED FERROUS METALLIC ABRASIVES |
ANSI Z49.1 : 2012 | SAFETY IN WELDING, CUTTING, AND ALLIED PROCESSES |
SSPC-SP 5 : 2015 | WHITE METAL BLAST CLEANING |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.