Skip to content
Please enter a keyword to search

  • UNI EN 12201-5 : 2012

    Current The latest, up-to-date edition.

    PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM

    Available format(s): 

    Language(s): 

    Published date:  11-04-2012

    Publisher:  Ente Nazionale Italiano di Unificazione (UNI)

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions, symbols and abbreviations
    4 Fitness for purpose of the system
    Bibliography

    Abstract - (Show below) - (Hide below)

    Defines the characteristics of the fitness for purpose of the assembled piping systems intended for the conveyance of water intended for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes UNI 10910-5. (06/2004) Supersedes UNI EN 13244-5. (04/2012)
    Document Type Standard
    Publisher Ente Nazionale Italiano di Unificazione (UNI)
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    UNI 9736 : 2014 FITTINGS MANUFACTURED WITH MIXED JUNCTION, METAL-POLYETHYLENE, FOR USE IN PIPELINES FOR THE SUPPLY OF GASEOUS FUELS, WATER AND OTHER FLUIDS UNDER PRESSURE AND METAL-POLYPROPYLENE PIPES FOR WATER SUPPLY AND OTHER FLUIDS UNDER PRESSURE - REQUIREMENTS, TESTING, FITNESS FOR PURPOSE AND ASSESSMENT OF CONFORMITY
    UNI TR 11288 : 2008 PLASTICS PIPING PRESSURE SYSTEMS FOR THE CONVEYANCE OF FLUIDS - POLYETHYLENE (PE) - FABRICATED FITTINGS
    UNI 10521 : 2012 WELDING OF PLASTIC MATERIALS - ELECTRO-FUSION WELDING - WELDING OF POLYETHYLENE PIPES AND/OR FITTINGS FOR GAS, WATER AND OTHERS PRESSURE FLUIDS PIPELINES
    UNI 10520 : 2009 WELDING OF PLASTIC MATERIALS - HEATED TOOL BUTT WELDING - WELDING OF POLYETHYLENE PIPES AND/OR FITTINGS FOR GAS, WATER AND OTHERS PRESSURE FLUIDS PIPELINES
    UNI 10761 : 2012 COORDINATION OF WELDING, PIPE LAYING AND TEST ACTIVITIES FOR POLYETHYLENE TRANSMISSION LINES OF GASEOUS FUELS, WATER AND OTHER FLUIDS UNDER PRESSURE - TASKS AND RESPONSIBILITIES, REQUIREMENTS FOR TRAINING, QUALIFICATION AND CERTIFICATION OF PERSONNEL
    UNI/TS 11508 : 2013 SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR THERMOPLASTIC MATERIALS - WELDING PROCEDURE SPECIFICATION (WPS) FOR ELECTROFUSION WELDING AND HEATED TOOL BUTT WELDING

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 13953:2001 Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
    ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
    ISO 13956:2010 Plastics pipes and fittings Decohesion test of polyethylene (PE) saddle fusion joints Evaluation of ductility of fusion joint interface by tear test
    EN 12201-3:2011+A1:2012 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings
    89/106/EEC : 1988 COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS
    EN ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006)
    EN ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006)
    ISO 1167-4:2007 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies
    EN 911:1995 Plastics piping systems - Elastomeric sealing ring type joints and mechanical joints for thermoplastics pressure piping - Test method for leaktightness under external hydrostatic pressure
    ISO 11414:2009 Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion
    EN 715:1994 Thermoplastics piping systems - End-load bearing joints between small diameter pressure pipes and fittings - Test method for leaktightness under internal water pressure, including end thrust
    EN 713:1993 Plastics piping systems - Mechanical joints between fittings and polyolefin pressure pipes - Test method for leaktightness under internal pressure of assemblies subjected to bending
    EN ISO 1167-4:2007 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 4: Preparation of assemblies (ISO 1167-4:2007)
    ISO 14236:2000 Plastics pipes and fittings Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems
    ISO 13954:1997 Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
    ISO 13955:1997 Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies
    EN 12201-2:2011+A1:2013 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes
    EN 12201-1:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General
    ISO 11413:2008 Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting
    CEN/TS 12201-7:2014 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity
    EN 712:1993 Thermoplastics piping systems - End-load bearing mechanical joints between pressure pipes and fittings - Test method for resistance to pull-out under constant longitudinal force
    ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective