UNI EN 1555-3 : 2013
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 3: FITTINGS
Superseded date
11-08-2022
Superseded by
Published date
01-01-2013
Sorry this product is not available in your region.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviations
4 Material
5 General characteristics
6 Geometrical characteristics
7 Mechanical characteristics
8 Physical characteristics
9 Performance requirements
10 Marking
11 Delivery conditions
Annex A (informative) - Examples of typical terminal
connection for electrofusion fittings
Annex B (normative) - Short-term pressure test method
Annex C (normative) - Tensile test for fitting/pipe
assemblies
Bibliography
Describes the characteristics of fusion fittings made from polyethylene (PE) as well as of mechanical fittings for piping systems in the field of the supply of gaseous fuels.
| DevelopmentNote |
Supersedes UNI ISO 4437. (08/2004) Supersedes UNI 8849 and UNI 8850. (07/2006)
|
| DocumentType |
Standard
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ONORM EN 1555-3 : 2013 | Identical |
| SN EN 1555-3 : 2010 + A1 2013 | Identical |
| NS EN 1555-3 : 2010 + A1 2012 | Identical |
| BS EN 1555-3 : 2010 | Identical |
| NEN EN 1555-3 : 2010 + A1 2012 | Identical |
| I.S. EN 1555-3:2010 | Identical |
| NF EN 1555-3 : 2010 + A1 2013 | Identical |
| EN 1555-3:2010+A1:2012 | Identical |
| DIN EN 1555-3:2013-01 | Identical |
| NBN EN 1555-3 : 2010 + A1 2013 | Identical |
| UNE-EN 1555-3:2011 | Identical |
| UNI/TR 11481 : 2013 | Usi del polietilene nelle linee dirette e nella distribuzione del gas combustibile - Tecnologie riconosciute e applicabili - Linee guida di orientamento per gli operatori |
| UNI 9736 : 2014 | FITTINGS MANUFACTURED WITH MIXED JUNCTION, METAL-POLYETHYLENE, FOR USE IN PIPELINES FOR THE SUPPLY OF GASEOUS FUELS, WATER AND OTHER FLUIDS UNDER PRESSURE AND METAL-POLYPROPYLENE PIPES FOR WATER SUPPLY AND OTHER FLUIDS UNDER PRESSURE - REQUIREMENTS, TESTING, FITNESS FOR PURPOSE AND ASSESSMENT OF CONFORMITY |
| UNI 11528 : 2014 | GAS PLANTS OVER 35 KW - DESIGN, INSTALLATION AND COMMISSIONING |
| UNI 10521 : 2012 | WELDING OF PLASTIC MATERIALS - ELECTRO-FUSION WELDING - WELDING OF POLYETHYLENE PIPES AND/OR FITTINGS FOR GAS, WATER AND OTHERS PRESSURE FLUIDS PIPELINES |
| UNI 10520 : 2009 | WELDING OF PLASTIC MATERIALS - HEATED TOOL BUTT WELDING - WELDING OF POLYETHYLENE PIPES AND/OR FITTINGS FOR GAS, WATER AND OTHERS PRESSURE FLUIDS PIPELINES |
| UNI 10761 : 2012 | COORDINATION OF WELDING, PIPE LAYING AND TEST ACTIVITIES FOR POLYETHYLENE TRANSMISSION LINES OF GASEOUS FUELS, WATER AND OTHER FLUIDS UNDER PRESSURE - TASKS AND RESPONSIBILITIES, REQUIREMENTS FOR TRAINING, QUALIFICATION AND CERTIFICATION OF PERSONNEL |
| EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
| EN 1555-1:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General |
| EN 10226-2:2005 | Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation |
| ISO 13953:2001 | Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 10838-3:2001 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 3: Thermoplastics fittings for pipes of nominal outside diameter less than or equal to 63 mm |
| EN ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006) |
| ISO 10838-2:2000 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm |
| EN ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006) |
| ISO 10838-1:2000 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm |
| ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies |
| IEC 60364-1:2005 | Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions |
| EN 1716:1997 | Plastics piping systems - Polyethylene (PE) tapping tees - Test method for impact resistance of an assembled tapping tee |
| CEN/TR 15438:2007 | Plastics piping systems - Guidance for coding of products and their intended uses |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| ISO 11922-1:1997 | Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
| HD 60364-1:2008/A11:2017 | LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 1: FUNDAMENTAL PRINCIPLES, ASSESSMENT OF GENERAL CHARACTERISTICS, DEFINITIONS |
| EN ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 4: Preparation of assemblies (ISO 1167-4:2007) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| ISO 13954:1997 | Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm |
| PREN 1555-4 : DRAFT 2008 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 4: VALVES |
| ISO 13955:1997 | Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies |
| EN 1555-5:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| EN 12007-2:2012 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 2: Specific functional requirements for polyethylene (MOP up to and including 10 bar) |
| ISO 11357-6:2008 | Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| EN 1555-2:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes |
| EN 60335-1:2012/A13:2017 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED) |
| CEN/TS 1555-7:2013 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity |
| EN ISO 1133:2005 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
| ISO 13950:2007 | Plastics pipes and fittings Automatic recognition systems for electrofusion joints |
| EN 12117:1997 | Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| ISO 1133:2005 | Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| ISO 13951:2015 | Plastics piping systems Test method for the resistance of plastic pipe/pipe or pipe/fitting assemblies to tensile loading |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.