UNI EN ISO 21809-5 : 2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 5: EXTERNAL CONCRETE COATINGS
18-11-2024
11-11-2010
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 General requirements
6 Information supplied by the purchaser
7 Materials
8 Concrete mix
9 Coating application
10 Curing methods
11 Inspection and testing
12 Repair of concrete coated pipe
13 Markings
14 Handling and storage
15 Test reports and certificate of compliance
Annex A (normative) - Water absorption test
Annex B (normative) - Shear resistance test
Bibliography
Describes the requirements for qualification, application, testing and handling of materials required for the application of reinforced concrete coating externally to either bare pipe or pre-coated pipe for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623.
| Committee |
CT 700
|
| DocumentType |
Standard
|
| PublisherName |
Ente Nazionale Italiano di Unificazione (UNI)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN ISO 21809-5:2017 | Identical |
| ISO 21809-5:2017 | Identical |
| EN 197-1:2011 | Cement - Part 1: Composition, specifications and conformity criteria for common cements |
| ISO/TS 29001:2010 | Petroleum, petrochemical and natural gas industries Sector-specific quality management systems Requirements for product and service supply organizations |
| ASTM C 171 : 2016 : REDLINE | Standard Specification for Sheet Materials for Curing Concrete |
| EN 10244-2:2009 | Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 2: Zinc or zinc alloy coatings |
| EN 13263-1:2005+A1:2009 | Silica fume for concrete - Part 1: Definitions, requirements and conformity criteria |
| EN 12390-7:2009 | Testing hardened concrete - Part 7: Density of hardened concrete |
| ASTM C 331 : 2005 | Standard Specification for Lightweight Aggregates for Concrete Masonry Units |
| ASTM C 1240 : 2015 : REDLINE | Standard Specification for Silica Fume Used in Cementitious Mixtures |
| EN 450-2:2005 | Fly ash for concrete - Part 2: Conformity evaluation |
| ASTM C 642 : 2013 : REDLINE | Standard Test Method for Density, Absorption, and Voids in Hardened Concrete |
| ISO 3183:2012 | Petroleum and natural gas industries Steel pipe for pipeline transportation systems |
| ASTM C 42/C 42M : 2016-10 | TEST METHOD FOR OBTAINING AND TESTING DRILLED CORES AND SAWED BEAMS OF CONCRETE |
| EN 10080:2005 | Steel for the reinforcement of concrete - Weldable reinforcing steel - General |
| EN 1008:2002 | Mixing water for concrete - Specification for sampling, testing and assessing the suitability of water, including water recovered from processes in the concrete industry, as mixing water for concrete |
| ASTM D 4643 : 2017 : REDLINE | Standard Test Method for Determination of Water Content of Soil and Rock by Microwave Oven Heating |
| ASTM C 637 : 2014 : REDLINE | Standard Specification for Aggregates for Radiation-Shielding Concrete |
| ISO 31-0:1992 | Quantities and units Part 0: General principles |
| ASTM C 332 : 2017 : REDLINE | Standard Specification for Lightweight Aggregates for Insulating Concrete |
| EN 10016-2:1994 | Non-alloy steel rod for drawing and/or cold rolling - Part 2: Specific requirements for general purposes rod |
| ASTM C 309 : 2011 : REDLINE | Standard Specification for Liquid Membrane-Forming Compounds for Curing Concrete |
| ISO 1920-5:2004 | Testing of concrete Part 5: Properties of hardened concrete other than strength |
| ASTM C 128 : 2015 : REDLINE | Standard Test Method for Relative Density (Specific Gravity) and Absorption of Fine Aggregate |
| EN 12620:2002+A1:2008 | Aggregates for concrete |
| ISO 14001:2015 | Environmental management systems — Requirements with guidance for use |
| ISO 10474:2013 | Steel and steel products — Inspection documents |
| EN 12390-2:2009 | Testing hardened concrete - Part 2: Making and curing specimens for strength tests |
| ASTM C 330 : 2005 | Standard Specification for Lightweight Aggregates for Structural Concrete |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ASTM D 4959 : 2016 : REDLINE | Standard Test Method for Determination of Water Content of Soil By Direct Heating |
| EN 450-1:2012 | Fly ash for concrete - Part 1: Definition, specifications and conformity criteria |
| ASTM A 810 : 2001 : R2008 | Standard Specification for Zinc-Coated (Galvanized) Steel Pipe Winding Mesh |
| ASTM C 40 : 2004 | Standard Test Method for Organic Impurities in Fine Aggregates for Concrete |
| EN 12504-1:2009 | Testing concrete in structures - Part 1: Cored specimens - Taking, examining and testing in compression |
| ASTM C 1176 : 2005 | Standard Practice for Making Roller-Compacted Concrete in Cylinder Molds Using a Vibrating Table |
| ACI 308.1 : 2011 | SPECIFICATION FOR CURING CONCRETE |
| ISO 13623:2017 | Petroleum and natural gas industries — Pipeline transportation systems |
| EN 934-2:2009+A1:2012 | Admixtures for concrete, mortar and grout - Part 2: Concrete admixtures - Definitions, requirements, conformity, marking and labelling |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.