VDI 3405 Blatt 1:2013-10
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Additive manufacturing processes, rapid manufacturing - Laser sintering of polymer parts - Quality control
Available format(s)
Hardcopy , PDF
Superseded date
08-04-2022
Superseded by
Language(s)
German - English
Published date
01-10-2013
Publisher
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Preliminary note
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviations
5 Testing of the raw powder
material
6 Process control
7 Testing part quality
8 Quality standards
9 Downstream processes
10 Safety and the environment
Annex
Bibliography
Defines to processes are an inherent part of the product development process and the production of serial parts.
| DocumentType |
Standard
|
| Pages |
37
|
| PublisherName |
Verlag des Vereins Deutscher Ingenieure
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| VDI 3405 Blatt 1.1:2017-08 (Draft) | Additive manufacturing processes - Laser sintering of polymer parts - Qualification of materials |
| VDI 3405 Blatt 3:2015-12 | Additive manufacturing processes, rapid manufacturing - Design rules for part production using laser sintering and laser beam melting |
| VDI 3405:2014-12 | Additive manufacturing processes, rapid manufacturing - Basics, definitions, processes |
| EN 444:1994 | Non-destructive testing - General principles for radiographic examination of metallic materials by X- and gamma-rays |
| VDI 3404:2009-12 | Additive fabrication - Rapid technologies (rapid prototyping) - Fundamentals, terms and definitions, quality parameters, supply agreements |
| ISO 3951-1:2013 | Sampling procedures for inspection by variables — Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL |
| ISO 1628-1:2009 | Plastics Determination of the viscosity of polymers in dilute solution using capillary viscometers Part 1: General principles |
| ISO 3167:2014 | Plastics Multipurpose test specimens |
| EN ISO 60:1999 | Plastics - Determination of apparent density of material that can be poured from a specified funnel (ISO 60:1977) |
| DIN EN ISO 1133-2:2012-03 | Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture (ISO 1133-2:2011) |
| EN ISO 1110:1997 | Plastics - Polyamides - Accelerated conditioning of test specimens (ISO 1110:1995) |
| ISO 9712:2012 | Non-destructive testing Qualification and certification of NDT personnel |
| DIN EN 473:2008-09 | NON-DESTRUCTIVE TESTING - QUALIFICATION AND CERTIFICATION OF NDT PERSONNEL - GENERAL PRINCIPLES |
| VDI 2209:2009-03 | 3D product modelling - Technical and organizational requirements - Procedures, tools, and applications - Cost-effective practical use |
| ISO 1133-1:2011 | Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method |
| EN ISO 11357-1:2016 | Plastics - Differential scanning calorimetry (DSC) - Part 1: General principles (ISO 11357-1:2016) |
| DIN ISO 2859-1:2014-08 | SAMPLING PROCEDURES FOR INSPECTION BY ATTRIBUTES - PART 1: SAMPLING SCHEMES INDEXED BY ACCEPTANCE QUALITY LIMIT (AQL) FOR LOT-BY-LOT INSPECTION (ISO 2859-1:1999 + COR. 1:2001 + AMD.1:2011) |
| EN ISO 527-2:2012 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012) |
| ISO 27547-1:2010 | Plastics — Preparation of test specimens of thermoplastic materials using mouldless technologies — Part 1: General principles, and laser sintering of test specimens |
| DIN EN ISO 1874-2:2013-03 | PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 1874-2:2012) |
| DIN EN ISO 60:2000-01 | Plastics - Determination of apparent density of material that can be poured from a specified funnel (ISO 60:1977); English version of DIN EN ISO 60 |
| ISO 1110:1995 | Plastics Polyamides Accelerated conditioning of test specimens |
| DIN ISO 3951-1:2016-06 | Sampling procedures for inspection by variables - Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL (ISO 3951-1:2013); Text in German and English |
| ISO 60:1977 | Plastics — Determination of apparent density of material that can be poured from a specified funnel |
| EN ISO 1133-2:2011 | Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture (ISO 1133-2:2011) |
| EN ISO 527-1:2012 | Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012) |
| EN 473:2008 | Non-destructive testing - Qualification and certification of NDT personnel - General principles |
| VDI 3405 Blatt 2:2013-08 | Additive manufacturing processes, rapid manufacturing - Beam melting of metallic parts - Qualification, quality assurance and post processing |
| EN ISO 1874-2:2012 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1874-2:2012) |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 1874-2:2012 | Plastics Polyamide (PA) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| EN ISO 9712:2012 | Non-destructive testing - Qualification and certification of NDT personnel (ISO 9712:2012) |
| ISO 6186:1998 | Plastics — Determination of pourability |
| EN ISO 3167:2014 | Plastics - Multipurpose test specimens (ISO 3167:2014) |
| VDI 1000:2017-02 | VDI Standardisation Work - Principles and procedures |
| EN ISO 1133-1:2011 | Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011) |
| DIN EN 16016-2:2012-01 | NON DESTRUCTIVE TESTING - RADIATION METHODS - COMPUTED TOMOGRAPHY - PART 2: PRINCIPLE, EQUIPMENT AND SAMPLES |
| DIN EN ISO 1628-1:2012-10 | Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometer - Part 1: General principles (ISO 1628-1:2009 + Amd 1:2012); German version EN ISO 1628-1:2009 + A1:2012 |
| DIN EN ISO 6186:1998-08 | Plastics - Determination of pourability (ISO 6186:1998) |
| EN ISO 11358:1997 | Plastics - Thermogravimetry (TG) of polymers - General principles (ISO 11358:1997) |
| ISO 3274:1996 | Geometrical Product Specifications (GPS) — Surface texture: Profile method — Nominal characteristics of contact (stylus) instruments |
| ISO 61:1976 | Plastics — Determination of apparent density of moulding material that cannot be poured from a specified funnel |
| DIN EN ISO 61:2000-01 | Plastics - Determination of apparent density of moulding material that cannot be poured from a specified funnel (ISO 61:1976); English version of DIN EN ISO 61 |
| ISO 291:2008 | Plastics Standard atmospheres for conditioning and testing |
| DIN EN 13068-3:2001-12 | NON-DESTRUCTIVE TESTING - RADIOSCOPIC TESTING - PART 3: GENERAL PRINCIPLES FOR THE RADIOSCOPIC TESTING OF METALLIC MATERIALS BY X- AND GAMMA RAYS |
| ISO 11358:1997 | Plastics Thermogravimetry (TG) of polymers General principles |
| EN ISO 6186:1998 | Plastics - Determination of pourability (ISO 6186:1998) |
| EN ISO 291:2008 | Plastics - Standard atmospheres for conditioning and testing (ISO 291:2008) |
| EN 16016-2:2011 | Non destructive testing - Radiation methods - Computed tomography - Part 2: Principle, equipment and samples |
| DIN EN ISO 11357-1:2016-05 (Draft) | PLASTICS - DIFFERENTIAL SCANNING CALORIMETRY (DSC) - PART 1: GENERAL PRINCIPLES (ISO 11357-1:2016) |
| DIN EN ISO 1110:1998-03 | PLASTICS - POLYAMIDES - ACCELERATED CONDITIONING OF TEST SPECIMENS |
| DIN 16742:2013-10 | PLASTICS MOULDED PARTS - TOLERANCES AND ACCEPTANCE CONDITIONS |
| ISO 1133-2:2011 | Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moisture |
| EN ISO 61:1999 | Plastics - Determination of apparent density of moulding material that cannot be poured from a specified funnel (ISO 61:1976) |
| ISO 11357-1:2016 | Plastics — Differential scanning calorimetry (DSC) — Part 1: General principles |
| EN 13068-3:2001 | Non-destructive testing - Radioscopic testing - Part 3: General principles of radioscopic testing of metallic materials by X- and gamma rays |
| DIN EN ISO 1133-1:2012-03 | Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011) |
| EN ISO 3274:1997 | Geometrical product specifications (GPS) - Surface texture: Profile method - Nominal characteristics of contact (stylus) instruments (ISO 3274:1996) |
| DIN EN ISO 3167:2014-11 | PLASTICS - MULTIPURPOSE TEST SPECIMENS (ISO 3167:2014) |
| ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.