01/708610 DC : DRAFT JUNE 2001
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ISO/DIS 17359 - CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - GENERAL GUIDELINES
12-03-2004
23-11-2012
Foreword
Introduction
1 Scope
2 Normative references
3 Term(s) and definition(s)
4 Overview of procedure
4.1 Condition monitoring procedure
5 Equipment audit
5.1 Identify equipment
5.2 Identify equipment function
6 Reliability and criticality audit
6.1 Reliability block diagram
6.2 Establish equipment
6.3 Failure modes, effects and criticality analysis
6.4 Alternative maintenance tasks
7 Measurement Method
7.1 Measurement technique
7.2 Accuracy of monitored parameters
7.3 Feasibility of measurement
7.4 Operating conditions during measurements
7.5 Measurement interval
7.6 Data acquisition rate
7.7 Record of monitored parameters
7.8 Select measurement location
7.9 Initial alert/alarm criteria
7.10 Baseline data
8 Data collection and analysis
8.1 Measurement and trending
8.2 Measurement comparison to alert/alarm criteria
8.3 Diagnosis and prognosis
8.4 Improving diagnosis and/or prognosis confidence
9 Determine maintenance action
10 Review
11 Training
Annex A (informative) Examples of condition monitoring
parameters
Annex B (informative) Matching fault(s) to measured
parameter(s) or technique(s)
Annex C (informative) Typical information to be recorded
when monitoring
C.1 Machine details
C.2 Measurements
C.3 Other information
Bibliography
| Committee |
GME/21/7
|
| DocumentType |
Draft
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| ISO 10816-4:2009 | Mechanical vibration Evaluation of machine vibration by measurements on non-rotating parts Part 4: Gas turbine sets with fluid-film bearings |
| BS EN 61078:2016 | Reliability block diagrams |
| ISO 13373-1:2002 | Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 1: General procedures |
| ISO 13379:2003 | Condition monitoring and diagnostics of machines General guidelines on data interpretation and diagnostics techniques |
| ISO 7919-4:2009 | Mechanical vibration Evaluation of machine vibration by measurements on rotating shafts Part 4: Gas turbine sets with fluid-film bearings |
| ISO 13380:2002 | Condition monitoring and diagnostics of machines General guidelines on using performance parameters |
| BS ISO 2382-14:1978 | Information technology. Vocabulary Reliability, maintenance and availability |
| ISO 10816-2:2009 | Mechanical vibration Evaluation of machine vibration by measurements on non-rotating parts Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min |
| ISO 7919-2:2009 | Mechanical vibration Evaluation of machine vibration by measurements on rotating shafts Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min |
| ISO 7919-1:1996 | Mechanical vibration of non-reciprocating machines Measurements on rotating shafts and evaluation criteria Part 1: General guidelines |
| BS 5760-3:1982 | Reliability of systems, equipment and components Guide to reliability practices: examples |
| ISO 10816-5:2000 | Mechanical vibration Evaluation of machine vibration by measurements on non-rotating parts Part 5: Machine sets in hydraulic power generating and pumping plants |
| ISO 10816-6:1995 | Mechanical vibration Evaluation of machine vibration by measurements on non-rotating parts Part 6: Reciprocating machines with power ratings above 100 kW |
| ISO 7919-5:2005 | Mechanical vibration Evaluation of machine vibration by measurements on rotating shafts Part 5: Machine sets in hydraulic power generating and pumping plants |
| ISO 2041:2009 | Mechanical vibration, shock and condition monitoring Vocabulary |
| BS 5760-23:1997 | Reliability of systems, equipment and components Guide to life cycle costing |
| BS 5760-0:1986 | Reliability of systems, equipment and components Introductory guide to reliability |
| ISO 13372:2004 | Condition monitoring and diagnostics of machines Vocabulary |
| ISO 1925:2001 | Mechanical vibration Balancing Vocabulary |
| BS 5760-7:1991 | Reliability of systems, equipment and components Guide to fault tree analysis |
| BS 5760-12:1993 | Reliability of systems, equipment and components Guide to the presentation of reliability, maintainability and availability predictions |
| ISO 10816-1:1995 | Mechanical vibration Evaluation of machine vibration by measurements on non-rotating parts Part 1: General guidelines |
| BS 5760-11:1994 | Reliability of systems, equipment and components Collection of reliability, availability, maintainability and maintenance support data from the field |
| ISO 7919-3:2009 | Mechanical vibration — Evaluation of machine vibration by measurements on rotating shafts — Part 3: Coupled industrial machines |
| BS 5760-10.5:1993 | Reliability of systems, equipment and components. Guide to reliability testing Compliance test plans for success ratio |
| BS 5760-4:1986 | Reliability of systems, equipment and components Guide to specification clauses relating to the achievement and development of reliability in new and existing items |
| BS 5760-6:1991 | Reliability of systems, equipment and components Guide to programmes for reliability growth |
| BS 5760-5:1991 | Reliability of systems, equipment and components Guide to failure modes, effects and criticality analysis (FMEA and FMECA) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.