Skip to content
Please enter a keyword to search

  • ISO 7919-2:2009

    View superseded by
    Withdrawn A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
    View superseded by

    Mechanical vibration Evaluation of machine vibration by measurements on rotating shafts Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Withdrawn date:  26-03-2019

    Language(s):  English, French

    Published date:  30-09-2009

    Publisher:  International Organization for Standardization

    Add To Cart

    Abstract - (Show below) - (Hide below)

    ISO 7919-2:2009 establishes provisions for applying evaluation criteria for the severity of in-situ, broad-band shaft vibration measured radial (i.e. transverse) to the shaft axis at, or close to, the main bearings. These are in terms of:

    - vibration under normal steady-state operating conditions;

    - vibration during other (non-steady-state) conditions when transient changes are taking place, including run up or run down, initial loading and load changes;

    - changes in vibration which can occur during normal steady-state operation.

    ISO 7919-2:2009 is applicable to land-based steam turbines and generators with power outputs greater than 50 MW and a normal operating speed of 1 500 r/min, 1800 r/min, 3 000 r/min or 3 600 r/min.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes ISO/FDIS 7919-2. (10/2009)
    Document Type Standard
    Publisher International Organization for Standardization
    Status Withdrawn
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS ISO 21940-31:2013 Mechanical vibration. Rotor balancing Susceptibility and sensitivity of machines to unbalance
    UNI ISO 10816-4 : 2010 MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 4: GAS TURBINE SETS WITH FLUID-FILM BEARINGS
    BS ISO 3977-3:2004 Gas turbines. Procurement Design requirements
    ISO 10817-1:1998 Rotating shaft vibration measuring systems Part 1: Relative and absolute sensing of radial vibration
    09/30192810 DC : DRAFT JAN 2009 BS ISO 10816-2 - MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 2: LAND-BASED STEAM TURBINES AND GENERATORS IN EXCESS OF 50 MW WITH NORMAL OPERATING SPEEDS OF 1500 R/MIN, 1800 R/MIN, 3000 R/MIN AND 3600 R/MIN
    ISO 10816-1:1995 Mechanical vibration Evaluation of machine vibration by measurements on non-rotating parts Part 1: General guidelines
    UNI ISO 10817-1 : 2011 ROTATING SHAFT VIBRATION MEASURING SYSTEMS - PART 1: RELATIVE AND ABSOLUTE SENSING OF RADIAL VIBRATION
    ISO 3977-3:2004 Gas turbines — Procurement — Part 3: Design requirements
    14/30244780 DC : 0 BS ISO 19859 - GAS TURBINE APPLICATIONS - REQUIREMENTS FOR POWER GENERATION
    01/714317 DC : DRAFT OCT 2001 ISO 18436-2 - CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - ACCREDITATION OF ORGANIZATIONS AND TRAINING AND CERTIFICATION OF PERSONNEL - PART 2: VIBRATION ANALYSIS
    09/30190941 DC : DRAFT JAN 2009 BS ISO 10816-4 - MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 4: GAS TURBINE SETS WITH FLUID-FILM BEARINGS
    BS ISO 20816-1:2016 Mechanical vibration. Measurement and evaluation of machine vibration General guidelines
    ISO 14661:2000 Thermal turbines for industrial applications (steam turbines, gas expansion turbines) General requirements
    ISO 10816-2:2009 Mechanical vibration Evaluation of machine vibration by measurements on non-rotating parts Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min
    ISO 19859:2016 Gas turbine applications Requirements for power generation
    VDI 3840:2004-05 Vibration analysis for machine sets
    VDI 3839 Blatt 5:2001-09 Instructions on measuring and interpreting the vibration of machines - Typical vibration patterns with electrical machines
    VDI 3840:2004-05 VIBRATION ANALYSIS FOR MACHINE SETS
    VDI 3839 Blatt 1:2001-03 Instructions on measuring and interpreting the vibrations of machines - General principles
    BS 7854-1(1996) : 1996 MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - GENERAL GUIDELINES
    ISO 21940-31:2013 Mechanical vibration — Rotor balancing — Part 31: Susceptibility and sensitivity of machines to unbalance
    00/702358 DC : DRAFT JAN 2000 ISO/DIS 13380 - CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - USE OF PERFORMANCE PARAMETERS - GENERAL GUIDELINES
    NF ISO 10816-2 : 2010 MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 2: LAND-BASED STEAM TURBINES AND GENERATORS IN EXCESS OF 50 MW WITH NORMAL OPERATING SPEEDS OF 1500 R/MIN, 1800 R/MIN, 3000 R/MIN AND 3600 R/MIN
    DIN ISO 17359:2011-09 CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - GENERAL GUIDELINES
    12/30265145 DC : 0 BS ISO 21940-31 - MECHANICAL VIBRATION - ROTOR BALANCING - PART 31: SUSCEPTIBILITY AND SENSITIVITY OF MACHINES TO UNBALANCE
    PD ISO/TR 19201:2013 Mechanical vibration. Methodology for selecting appropriate machinery vibration standards
    17/30341578 DC : DRAFT MAY 2017 BS ISO 17359 - CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - GENERAL GUIDELINES
    BS ISO 14661:2000 Thermal turbines for industrial applications (steam turbines, gas expansion turbines). General requirements
    03/303213 DC : DRAFT FEB 2003 ISO 14839-2 - MECHANICAL VIBRATION - VIBRATION OF ROTATING MACHINERY EQUIPPED WITH ACTIVE MAGNETIC BEARINGS - PART 2: EVALUATION OF VIBRATION
    DIN ISO 20816-1:2015-12 (Draft) MECHANICAL VIBRATION - MEASUREMENT AND EVALUATION OF MACHINE VIBRATION - PART 1: GENERAL GUIDELINES (ISO 20816-1:2016)
    IEEE C50.13 : 2014 CYLINDRICAL-ROTOR 50 HZ AND 60 HZ, SYNCHRONOUS GENERATORS RATED 10 MVA AND ABOVE
    BS ISO 13373-1:2002 Condition monitoring and diagnostics of machines. Vibration condition monitoring General procedures
    BS ISO 14839-2:2004 Mechanical vibration. Vibration of rotating machinery equipped with active magnetic bearings Evaluation of vibration
    BS ISO 10816-1 : 1995 MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 1: GENERAL GUIDELINES
    UNI ISO 10816-2 : 2010 MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 2: LAND-BASED STEAM TURBINES AND GENERATORS IN EXCESS OF 50 MW WITH NORMAL OPERATING SPEEDS OF 1500 R/MIN, 1800 R/MIN, 3000 R/MIN AND 3600 R/MIN
    09/30197816 DC : 0 BS ISO 10816-1/AMD1 - MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 1: GENERAL GUIDELINES
    09/30190938 DC : DRAFT JAN 2009 BS ISO 7919-4 - MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON ROTATING SHAFTS - PART 4: GAS TURBINE SETS WITH FLUID-FILM BEARINGS
    IEEE 1129-2014 IEEE Guide for Online Monitoring of Large Synchronous Generators (10 MVA and Above)
    IEEE 115-2009 REDLINE IEEE Guide for Test Procedures for Synchronous Machines Part I—Acceptance and Performance Testing Part II—Test Procedures and Parameter Determination for Dynamic Analysis
    BS ISO 19859:2016 Gas turbine applications. Requirements for power generation
    ISO/TR 19201:2013 Mechanical vibration Methodology for selecting appropriate machinery vibration standards
    01/708610 DC : DRAFT JUNE 2001 ISO/DIS 17359 - CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - GENERAL GUIDELINES
    BS ISO 10817-1:1999 Rotating shaft vibration measuring systems Relative and absolute sensing of radial vibration
    BS ISO 10816-2:2009 Mechanical vibration. Evaluation of machine vibration by measurements on non-rotating parts Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1500 r/min, 1800 r/min, 3000 r/min and 3600 r/min
    10/30200372 DC : 0 BS ISO 17359 - CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - GENERAL GUIDELINES
    BS ISO 7919-1:1996 Mechanical vibration of non-reciprocating machines. Measurements on rotating shafts and evaluation criteria General guidelines
    15/30328956 DC : 0 BS ISO 20816-1 - MECHANICAL VIBRATION - MEASUREMENT AND EVALUATION OF MACHINE VIBRATION - PART 1: GENERAL GUIDELINES
    ISO 14839-2:2004 Mechanical vibration — Vibration of rotating machinery equipped with active magnetic bearings — Part 2: Evaluation of vibration
    ISO 13373-1:2002 Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 1: General procedures
    DIN ISO 10816-1:1997-08 MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 1: GENERAL GUIDELINES
    DIN ISO 10816-2:2010-06 MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 2: LAND-BASED STEAM TURBINES AND GENERATORS IN EXCESS OF 50 MW WITH NORMAL OPERATING SPEEDS OF 1500 R/MIN, 1800 R/MIN, 3000 R/MIN AND 3600 R/MIN

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 10816-4:2009 Mechanical vibration Evaluation of machine vibration by measurements on non-rotating parts Part 4: Gas turbine sets with fluid-film bearings
    ISO 13373-1:2002 Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 1: General procedures
    ISO 10816-2:2009 Mechanical vibration Evaluation of machine vibration by measurements on non-rotating parts Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min
    ISO 10814:1996 Mechanical vibration Susceptibility and sensitivity of machines to unbalance
    ISO 7919-1:1996 Mechanical vibration of non-reciprocating machines Measurements on rotating shafts and evaluation criteria Part 1: General guidelines
    ISO 10816-5:2000 Mechanical vibration Evaluation of machine vibration by measurements on non-rotating parts Part 5: Machine sets in hydraulic power generating and pumping plants
    ISO 13373-2:2016 Condition monitoring and diagnostics of machines Vibration condition monitoring Part 2: Processing, analysis and presentation of vibration data
    ISO 2041:2009 Mechanical vibration, shock and condition monitoring Vocabulary
    ISO 10816-1:1995 Mechanical vibration Evaluation of machine vibration by measurements on non-rotating parts Part 1: General guidelines
    ISO 10816-7:2009 Mechanical vibration Evaluation of machine vibration by measurements on non-rotating parts Part 7: Rotodynamic pumps for industrial applications, including measurements on rotating shafts
    ISO 10817-1:1998 Rotating shaft vibration measuring systems Part 1: Relative and absolute sensing of radial vibration
    ISO 5348:1998 Mechanical vibration and shock Mechanical mounting of accelerometers
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective