• Shopping Cart
    There are no items in your cart

02/705659 DC : DRAFT APR 2002

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

ISO/DIS 21049 - PUMPS - SHAFT SEALING SYSTEMS FOR CENTRIFUGAL AND ROTARY PUMPS

Superseded date

10-02-2005

Superseded by

BS EN ISO 21049:2004

Published date

23-11-2012

Sorry this product is not available in your region.

Foreword
Introduction
1 Scope
   1.1 General
   1.2 Seal categories, types and arrangements
   1.3 Objectives
   1.4 Specifying and/or purchasing a sealing system
2 Normative references
3 Terms and definitions
4 Unit responsibility
5 Dimensions
6 Design requirements
   6.1 Common design requirements (all categories)
   6.2 Design requirements (category specific)
7 Specific seal configurations
   7.1 Arrangement 1 seals
   7.2 Arrangement 2 seals
   7.3 Arrangement 3 seals
8 Accessories
   8.1 Auxiliary piping systems
   8.2 Mechanical seal flush/cooling systems (Group I)
   8.3 Quench systems (Group II)
   8.4 Cooling-water systems (Group III)
   8.5 Accessories and auxiliary system components
   8.6 Barrier/buffer fluid and seal flush positive circulating
        devices
9 Instrumentation
   9.1 General
   9.2 Temperature indicating gauges
   9.3 Thermowells
   9.4 Pressure gauges
   9.5 Switches
   9.6 Level indicators
   9.7 Flow indicators
   9.8 Relief valves
   9.9 Regulators
   9.10 Pressure amplifiers
10 Inspection, testing, and preparation for shipment
   10.1 General
   10.2 Inspection
   10.3 Testing
   10.4 Preparation for shipment
11 Data transfer
   11.1 General
   11.2 Proposal data
   11.3 Contract data
Annex A (informative) Recommended seal selection procedure
        A.1 Assumptions and instructions
        A.2 Tutorial clause
        A.3 Tutorial seal selection - Sheet 6
        A.4 Tutorial on sheet 7 through sheet 9 of seal selection
            procedure
Annex B (informative) Heat generation and heat soak calculations
        B.1 Estimating of seal-generated heat
        B.2 Temperature rise in the seal chamber
Annex C (normative) Materials and material descriptions
        C.1 Typical descriptions of miscellaneous materials for
            mechanical seal parts
        C.2 Typical temperature limitations for seal materials in
            hydrocarbon service
        C.3 Typical temperature limitation guidelines for secondary
            seal materials
        C.4 Tutorial on selection of elastomers
Annex D (normative) Standard flush plans and auxiliary hardware
Annex E (informative) Inspector checklist
Annex F (normative) Mechanical seal data sheets
Annex G (normative) Mechanical seals data requirements form
Annex H (normative) Seal and pump vendor interface
Annex I (normative) Mechanical seal test qualification form
Annex J (informative) Mechanical seal codes
        J.1 Mechanical seals
        J.2 First Letter: Seal Category (1, 2, 3)
        J.3 Second letter: Seal Arrangement (1, 2, 3)
        J.4 Third letter: Seal Type (A, B, C)
        J.5 Fourth number(s): flush arrangement
        J.6 Non-standard reference
        J.7 Summary
Bibliography

Committee
MCE/6
DocumentType
Draft
PublisherName
British Standards Institution
Status
Superseded
SupersededBy

API 682 : 2014 PUMPS - SHAFT SEALING SYSTEMS FOR CENTRIFUGAL AND ROTARY PUMPS
API 750 : 1990 MANAGEMENT OF PROCESS HAZARDS
ASTM B 575 : 2017 : REDLINE Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, Low-Carbon Nickel-Chromium-Molybdenum-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Tungsten, and Low-Carbon Nickel-Molybdenum-Chromium Alloy Plate, Sheet, and Strip
API 520-1 : 2014 SIZING, SELECTION, AND INSTALLATION OF PRESSURE-RELIEVING DEVICES - PART 1: SIZING AND SELECTION
ASTM B 473 : 2007 Standard Specification for UNS N08020, UNS N08024, and UNS N08026 Nickel Alloy Bar and Wire
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
ISO 2858:1975 End-suction centrifugal pumps (rating 16 bar) — Designation, nominal duty point and dimensions
NFPA 70 : 2017 NATIONAL ELECTRICAL CODE
API 526 : 2017 FLANGED STEEL PRESSURE-RELIEF VALVES
ASTM E 125 : 1963 : R2003 Standard Reference Photographs for Magnetic Particle Indications on Ferrous Castings
ISO 286-2:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
API 610 : 2010 CENTRIFUGAL PUMPS FOR PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES
ISO 13709:2009 Centrifugal pumps for petroleum, petrochemical and natural gas industries
ISO 261:1998 ISO general purpose metric screw threads — General plan
ISO 7005-1:2011 Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems
ASTM E 709 : 2015 : REDLINE Standard Guide for Magnetic Particle Testing
AWS D1.1 : 2000 STRUCTURAL WELDING CODE - STEEL
ASTM A 524 : 1996 Standard Specification for Seamless Carbon Steel Pipe for Atmospheric and Lower Temperatures
ISO 3448:1992 Industrial liquid lubricants — ISO viscosity classification
API 520-2 : 2015 SIZING, SELECTION, AND INSTALLATION OF PRESSURE-RELIEVING DEVICES - PART 2: INSTALLATION
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
ISO 3069:2000 End-suction centrifugal pumps — Dimensions of cavities for mechanical seals and for soft packing
ASTM D 1418 : 2017 : REDLINE Standard Practice for Rubber and Rubber Latices—Nomenclature

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.