13/30264471 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS ISO 21172-1 - GAS CYLINDERS - WELDED STEEL PRESSURE DRUMS UP TO 3000 LITRES CAPACITY FOR THE TRANSPORT OF GASES - DESIGN AND CONSTRUCTION - PART 1: CAPACITIES UP TO 1000 LITRES
Hardcopy , PDF
30-04-2015
English
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Inspection and testing
6 Materials
7 Design
8 Lifting attachments and rolling bands
9 Manufacturing process - Welding procedures
10 Fabrication
11 Welded joints
12 Surface finish of material
13 Assembly
14 Weld defect repairs
15 Construction and workmanship
16 Testing and examination
17 Marking
18 Certification
19 Certificate
Annex A (informative) - Description and evaluation of
manufacturing of a welded steel pressure drums at
the time of visual inspection
Annex B (informative) - Example of calculation note for
determination of thickness for shell and dished end
for pressure drums according to 5.4
Annex C Acceptance certificate (informative)
Annex D (informative) - Hot pressure welded heads
Bibliography
BS ISO 21172-1
| Committee |
PVE/3/3
|
| DocumentType |
Draft
|
| Pages |
48
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| ISO 9328-4:2011 | Steel flat products for pressure purposes — Technical delivery conditions — Part 4: Nickel-alloy steels with specified low temperature properties |
| ISO 2063:2005 | Thermal spraying — Metallic and other inorganic coatings — Zinc, aluminium and their alloys |
| ISO 1392:1977 | Determination of crystallizing point — General method |
| ISO 11114-1:2012 | Gas cylinders — Compatibility of cylinder and valve materials with gas contents — Part 1: Metallic materials |
| ISO 10920:1997 | Gas cylinders — 25E taper thread for connection of valves to gas cylinders — Specification |
| ISO 3879:1977 | Welded joints — Recommended practice for liquid penetrant testing |
| ISO 9606-1:2012 | Qualification testing of welders — Fusion welding — Part 1: Steels |
| ISO 4978:1983 | Flat rolled steel products for welded gas cylinders |
| EN 462-3:1996 | Non-destructive testing - Image quality of radiographs - Part 3: Image quality classes for ferrous metals |
| ISO 4706:2008 | Gas cylinders — Refillable welded steel cylinders — Test pressure 60 bar and below |
| ISO 9328-3:2011 | Steel flat products for pressure purposes — Technical delivery conditions — Part 3: Weldable fine grain steels, normalized |
| ISO 5817:2014 | Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections |
| ISO 9328-5:2011 | Steel flat products for pressure purposes — Technical delivery conditions — Part 5: Weldable fine grain steels, thermomechanically rolled |
| ISO 15614-1:2017 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
| ISO 7438:2016 | Metallic materials — Bend test |
| ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials — Qualification based on previous welding experience |
| ISO 1106-1:1984 | Recommended practice for radiographic examination of fusion welded joints — Part 1: Fusion welded butt joints in steel plates up to 50 mm thick |
| ISO 21028-2:2004 | Cryogenic vessels — Toughness requirements for materials at cryogenic temperature — Part 2: Temperatures between -80 degrees C and -20 degrees C |
| ISO 148:1983 | Steel — Charpy impact test (V-notch) |
| ISO 11114-2:2013 | Gas cylinders — Compatibility of cylinder and valve materials with gas contents — Part 2: Non-metallic materials |
| ISO 9328-2:2011 | Steel flat products for pressure purposes — Technical delivery conditions — Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
| ISO 17639:2003 | Destructive tests on welds in metallic materials — Macroscopic and microscopic examination of welds |
| ISO 9328-1:2011 | Steel flat products for pressure purposes — Technical delivery conditions — Part 1: General requirements |
| ISO 17637:2016 | Non-destructive testing of welds — Visual testing of fusion-welded joints |
| ISO 11114-4:2017 | Transportable gas cylinders — Compatibility of cylinder and valve materials with gas contents — Part 4: Test methods for selecting steels resistant to hydrogen embrittlement |
| ISO 11116-1:1999 | Gas cylinders — 17E taper thread for connection of valves to gas cylinders — Part 1: Specifications |
| ISO 4136:2012 | Destructive tests on welds in metallic materials — Transverse tensile test |
| ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials — Qualification based on pre-production welding test |
| ISO 17638:2016 | Non-destructive testing of welds — Magnetic particle testing |
| ISO 13769:2007 | Gas cylinders — Stamp marking |
| ASTM A 285/A285M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength |
Important note : Users cannot be edited or removed once added to your Multi user PDF.Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Logging out.