16/30318653 DC : 0
NA
Status of Standard is Unknown
BS EN 681-1 - ELASTOMERIC SEALS - MATERIAL REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
Hardcopy , PDF
English
Important note : Users cannot be edited or removed once added to your Multi user PDF.
European foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Application
5 Requirements
6 Test methods
7 Assessment and verification of constancy of
performance - AVCP
8 Designation
9 Marking and labelling
Annex A (normative) - Determination of stress
relaxation in tension
Annex B (normative) - Determination of compression set
in hot water at 110 degrees C
Annex C (normative) - Determination of splice strength
Annex D (informative) - Guidance on storage of seals
Annex ZA (informative) - Relationship of this European
Standard with Regulation (EU) No.305/2011
Bibliography
BS EN 681-1.
| Committee |
PRI/70
|
| DocumentType |
Draft
|
| Pages |
35
|
| PublisherName |
British Standards Institution
|
| Status |
NA
|
| Standards | Relationship |
| PREN 681-1 : DRAFT 2016 | Identical |
| ISO/IEC 17065:2012 | Conformity assessment — Requirements for bodies certifying products, processes and services |
| ISO 3951-1:2013 | Sampling procedures for inspection by variables — Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL |
| ISO 815-2:2014 | Rubber, vulcanized or thermoplastic Determination of compression set Part 2: At low temperatures |
| ISO/IEC 17021:2011 | Conformity assessment Requirements for bodies providing audit and certification of management systems |
| ISO 23529:2016 | Rubber General procedures for preparing and conditioning test pieces for physical test methods |
| ISO 815-1:2014 | Rubber, vulcanized or thermoplastic Determination of compression set Part 1: At ambient or elevated temperatures |
| ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
| ISO 2285:2013 | Rubber, vulcanized or thermoplastic Determination of tension set under constant elongation, and of tension set, elongation and creep under constant tensile load |
| ISO 3384-1:2011 | Rubber, vulcanized or thermoplastic Determination of stress relaxation in compression Part 1: Testing at constant temperature |
| ISO 1431-1:2012 | Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing |
| ISO 3302-1:2014 | Rubber — Tolerances for products — Part 1: Dimensional tolerances |
| ISO 9691:1992 | Rubber — Recommendations for the workmanship of pipe joint rings — Description and classification of imperfections |
| EN ISO/IEC 17065:2012 | Conformity assessment - Requirements for bodies certifying products, processes and services (ISO/IEC 17065:2012) |
| ISO 6914:2013 | Rubber, vulcanized or thermoplastic Determination of ageing characteristics by measurement of stress relaxation in tension |
| ISO 3387:2012 | Rubber Determination of crystallization effects by hardness measurements |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| ISO 3601-1:2012 | Fluid power systems — O-rings — Part 1: Inside diameters, cross-sections, tolerances and designation codes |
| ISO 3601-3:2005 | Fluid power systems O-rings Part 3: Quality acceptance criteria |
| ISO 48:2010 | Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) |
| ISO 34-2:2015 | Rubber, vulcanized or thermoplastic Determination of tear strength Part 2: Small (Delft) test pieces |
| ISO 1629:2013 | Rubber and latices — Nomenclature |
| ISO 3951-2:2013 | Sampling procedures for inspection by variables — Part 2: General specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection of independent quality characteristics |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| EN ISO/IEC 17021-1:2015 | Conformity assessment - Requirements for bodies providing audit and certification of management systems - Part 1: Requirements (ISO/IEC 17021-1:2015) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.