AS 1627.4-2005
Current
The latest, up-to-date edition.
Metal finishing - Preparation and pretreatment of surfaces Abrasive blast cleaning of steel (Reconfirmed 2017)
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
English
23-12-2005
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Specifies abrasive blastcleaning methods for the preparation of steel surfaces before coating with paints and related products.
| Committee |
MT-009
|
| DocumentType |
Standard
|
| ISBN |
0 7337 7071 1
|
| Pages |
27
|
| ProductNote |
Reconfirmed 07/04/2017.This standard has been reconfirmed in Australia in 2017 and remains current in New Zealand. Reconfirmation Notice 07/04/2017
|
| PublisherName |
Standards Australia
|
| Status |
Current
|
| Supersedes |
This Standard specifies abrasive blast cleaning methods for the preparation of steel surfaces before coating with paints and related products. It also contains information on the effectiveness of the individual methods and their fields of application.NOTES:Information on purchasing guidelines may be found in Appendix A.Information on abrasive blasting of surfaces other than steel is discussed in Appendix D.This Standard is applicable to new and corroded steel surfaces and also to steel surfaces that are uncoated or have been previously coated with paints and related products.These methods are essentially intended for the surface preparation of hot-rolled steel but could also be used for cold-rolled steel of sufficient thickness to withstand the deformation caused by the impact of abrasive.Items considered as a part of surface preparation before coating are edge grinding, removal of grease and oil, removal of weld spatter, removal of burrs and other sharp edges, grinding of welds, filling of pits, porosity of welds and other surface imperfections and removal of water-soluble contaminants that may cause premature failure of the coating system (see AS1627.0 for more information). Such defects cannot be satisfactorily treated by abrasive blast cleaning.WARNING: THE PROCEDURES DESCRIBED IN THIS STANDARD ARE INTENDED TO BE CARRIED OUT BY SUITABLY TRAINED AND SUPERVISED PERSONNEL. THE SUBSTANCES AND PROCEDURES USED IN THESE METHODS MAY BE INJURIOUS TO HEALTH IF ADEQUATE PRECAUTIONS ARE NOT TAKEN. ATTENTION IS DRAWN IN THE TEXT TO CERTAIN SPECIFIC HAZARDS. THIS STANDARD REFERS TO THE TECHNICAL SUITABILITY OF THE METHODS AND DOES NOT ABSOLVE THE USER FROM STATUTORY OBLIGATIONS RELATING TO HEALTH AND SAFETY.NOTE: For guidance on working place hazards refer to Appendix C.
| Standards | Relationship |
| ISO 8504-2:2000 | Identical |
Originated as AS CK9.4-1964.
Previous edition AS 1627.4-2002.
Fourth edition 2005.
| AS 1627.0-1997 | Metal finishing - Preparation and pretreatment of surfaces Method selection guide (Reconfirmed 2017) |
| AS/NZS 2161.1:2000 | Occupational protective gloves Selection, use and maintenance |
| AS/NZS 4501.2:2006 | Occupational protective clothing General requirements |
| AS/NZS 1270:2002 | Acoustics - Hearing protectors (Reconfirmed 2014) |
| AS/NZS 1716:2003 | Respiratory protective devices |
| AS 1627.9-2002 | Metal finishing - Preparation and pretreatment of surfaces Pictorial surface preparation standards for painting steel surfaces (Reconfirmed 2017) |
| AS/NZS 4501.2:1999 | Occupational protective clothing General requirements |
| AS 3894.5-2002 | Site testing of protective coatings Determination of surface profile |
| AS/NZS 2312:2002 | Guide to the protection of structural steel against atmospheric corrosion by the use of protective coatings |
| AS 1627.1-2003 | Metal finishing - Preparation and pretreatment of surfaces Removal of oil, grease and related contamination (Reconfirmed 2017) |
| AS 3894.6-2002 | Site testing of protective coatings Determination of residual contaminants (Reconfirmed 2013) |
| AS 1627.2-2002 | Metal finishing - Preparation and pretreatment of surfaces Power tool cleaning (Reconfirmed 2017) |
| AS/NZS 1715:1994 | Selection, use and maintenance of respiratory protective devices |
| AS/NZS 1336:1997 | Recommended practices for occupational eye protection |
| AS/NZS 2210.1:1994 | Occupational protective footwear - Guide to selection, care and use |
| AS 3894.9-2003 | Site testing of protective coatings Determination of adhesion |
| AS 4361.1-1995 | Guide to lead paint management - Industrial applications |
| AS/NZS 4361.1:2017 | Guide to hazardous paint management Lead and other hazardous metallic pigments in industrial applications |
| AS 4848.1-2006 | Application specifications for coating systems Single coat inorganic (ethyl) zinc silicate - Solvent-borne |
| AS/NZS 3750.8:1994 | Paints for steel structures Vinyl paints - Primer, high-build and gloss (Reconfirmed 2013) |
| AS 2470-2005 | Steel cylinders for compressed gases - Welded three-piece construction with longitudinal joint - 11 kg to 150 kg (Reconfirmed 2016) |
| AS/NZS 2311:2009 | Guide to the painting of buildings |
| AS 1056.3-1991 | Storage water heaters - Specific requirements for water heaters with composite shells |
| AS 3894.6-2002 | Site testing of protective coatings Determination of residual contaminants (Reconfirmed 2013) |
| AS/NZS 3750.9:1994 | Paints for steel structures - Organic zinc-rich primer |
| AS 2309-2008 | Durability of galvanized and electrogalvanized zinc coatings for the protection of steel in structural applications - Atmospheric |
| AS/NZS 3509:2003 | LP Gas fuel vessels for automotive use |
| AS 1627.0-1997 | Metal finishing - Preparation and pretreatment of surfaces Method selection guide (Reconfirmed 2017) |
| AS 3597-1993 | Structural and pressure vessel steel - Quenched and tempered plate |
| AS/NZS 3750.11:2009 | Paints for steel structures Chlorinated rubber - High-build and gloss |
| AS 2832.1-2004 | Cathodic protection of metals Pipes and cables |
| AS 3750.2-1994 | Paints for steel structures - Ultra high-build paint |
| HB 84-2006 | Guide to Concrete Repair and Protection |
| AS/NZS 3750.7:2009 | Paints for steel structures Aluminium paint (Reconfirmed 2021) |
| AS/NZS 1518:2002 | External extruded high-density polyethylene coating system for pipes (Reconfirmed 2016) |
| AS 4848.1:2019 | Application specifications for coating systems Single coat inorganic (ethyl) zinc silicate - Solvent-borne |
| AS 4793:2020 | Mechanical tapping bands for waterworks purposes |
| AS 2062-1997 | Non-destructive testing - Penetrant testing of products and components |
| AS/NZS 3750.6:2009 | Paints for steel structures Full gloss polyurethane (two-pack) (Reconfirmed 2020) |
| AS 4321-2001 | Fusion-bonded medium-density polyethylene coating and lining for pipes and fittings (Reconfirmed 2019) |
| AS 2518-1992 | Fusion-bonded low-density polyethylene coating for pipes and fittings |
| AS/NZS 4793:2009 | Mechanical tapping bands for waterworks purposes |
| AS 3978-2003 | Non-destructive testing - Visual inspection of metal products and components (Reconfirmed 2022) |
| AS/NZS 3750.11:1996 | Paints for steel structures - Chlorinated rubber - High-build and gloss |
| AS/NZS 3750.9:2009 | Paints for steel structures Organic zinc-rich primer (Reconfirmed 2019) |
| AS 5081-2008 | Hydraulically operated automatic control valves for waterworks purposes (Reconfirmed 2016) |
| AS 3577-2006 | Steel cylinders for compressed gases - Welded - 150 kg to 500 kg |
| AS/NZS 3750.4:1994 | Paints for steel structures Bitumen paint (Reconfirmed 2013) |
| AS 4956-2008 | Air valves for water supply |
| AS/NZS 3750.3:2008 | Paints for steel structures Heat resisting - Exterior (Reconfirmed 2020) |
| AS 4795.1-2011 | Butterfly valves for waterworks purposes Wafer and lugged (Reconfirmed 2022) |
| AS 5100.8:2017 | Bridge design Rehabilitation and strengthening of existing bridges |
| AS 4457.1-2007 | Earth-moving machinery - Off-the-road wheels, rims and tyres - Maintenance and repair Wheel assemblies and rim assemblies |
| AS 4883-2008 | Air valves for sewerage |
| AS/NZS 2312:2002 | Guide to the protection of structural steel against atmospheric corrosion by the use of protective coatings |
| AS/NZS 3750.3:1994 | Paints for steel structures - Heat resisting - Exterior |
| AS 4883:2017 | Air valves for sewerage |
| AS 1856-2004 | Electroplated coatings - Silver |
| AS 4822-2008 | External field joint coatings for steel pipelines |
| AS 3862:2020 | External fusion-bonded epoxy coating for steel pipes |
| AS 3750.10-2008 | Paints for steel structures Full gloss epoxy (two-pack) (Reconfirmed 2019) |
| AS 2429-2004 | Electroplated coatings of rhodium for general engineering applications |
| AS/NZS 3750.12:1996 | Paints for steel structures Alkyd/micaceous iron oxide (Reconfirmed 2013) |
| AS 4795-2006 | Butterfly valves for waterworks purposes |
| AS/NZS 3750.1:2008 | Paints for steel structures Epoxy mastic (two-pack) - For rusted steel (Reconfirmed 2020) |
| AS/NZS 4680:2006 | Hot-dip galvanized (zinc) coatings on fabricated ferrous articles (Reconfirmed 2017) |
| AS 2699.3:2020 | Built-in components for masonry construction Lintels and shelf angles (durability requirements) |
| AS/NZS 3750.5:2008 | Paints for steel structures Acrylic full gloss (two-pack) (Reconfirmed 2020) |
| AS 5612-2013 | Butterfly valves for general purposes |
| AS/NZS 4792:2006 | Hot-dip galvanized (zinc) coatings on ferrous hollow sections, applied by a continuous or a specialized process (Reconfirmed 2017) |
| AS 4361.1-1995 | Guide to lead paint management - Industrial applications |
| AS 2832.2-2003 | Cathodic protection of metals Compact buried structures |
| AS 4956:2017 | Air valves for water supply |
| AS/NZS 3750.7:1994 | Paints for steel structures - Aluminium paint |
| AS 2832.3-2005 | Cathodic protection of metals Fixed immersed structures |
| AS/NZS 3750.20:2008 | Paints for steel structures Anticorrosive metal primer - Solvent-borne - Lead and chromate free (Reconfirmed 2020) |
| AS 2469-2005 | Steel cylinders for compressed gases - Welded two-piece construction - 0.1 kg to 150 kg |
| AS 3750.1-1994 | Paints for steel structures - Epoxy mastic (two-pack) - For rusted steel |
| AS/NZS 5131:2016 | Structural steelwork - Fabrication and erection |
| AS 4795.2-2011 | Butterfly valves for waterworks purposes Double flanged |
| AS/NZS 3750.5:1994 | Paints for steel structures - Acrylic full gloss (two-pack) |
| AS/NZS 3509:2009 | LP Gas fuel vessels for automotive use (Reconfirmed 2019) |
| AS 2468-1989 | Steel cylinders for compressed gases - Brazed - 0.1 kg to 11 kg |
| AS/NZS 3750.10:1994 | Paints for steel structures Full gloss epoxy (two-pack) |
| AS/NZS 3750.2:2008 | Paints for steel structures Ultra high-build paint (Reconfirmed 2020) |
| AS 3894.5-2002 | Site testing of protective coatings Determination of surface profile |
| AS 2832.4-2006 | Cathodic protection of metals Internal surfaces (Reconfirmed 2016) |
| AS/NZS 2311:2017 | Guide to the Painting of Buildings |
| AS 1627.9-2002 | Metal finishing - Preparation and pretreatment of surfaces Pictorial surface preparation standards for painting steel surfaces (Reconfirmed 2017) |
| AS 4025.4-1994 | Paints for equipment including ships Solvent-borne - Lead and chromate free - Anticorrosive metal primer |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.