AS 2229.2-1988

1 - AS 2229.2-1988 ELECTRICAL EQUIPMENT FOR EXPLOSIVE ATMOSPHERES - ELECTRICAL SYSTEMS OF DISPENSING EQUIPMENT - LIQUEFIED PETRO
4 - PREFACE
5 - CONTENTS
6 - SECTION 1. SCOPE AND GENERAL
6 - 1.1 SCOPE.
6 - 1.2 REFERENCED DOCUMENTS.
6 - 1.3 DEFINITIONS.
6 - 1.3.1 Dispenser cabinet
6 - 1.3.2 Liquefied petroleum gas (LP gas)
6 - 1.3.3 Liquefied petroleum gas dispensing equipment
6 - 1. 4 GROUPING.
6 - 1.5 TEMPERATURE CLASSIFICATION.
7 - SECTION 2. DESIGN AND CONSTRUCTION
7 - 2.1 GENERAL.
7 - 2.2 EQUIPMENT WITHIN DISPENSER CABINET.
7 - 2.3 EQUIPMENT OUTSIDE DISPENSER CABINET.
7 - 2.4 DISPENSER CABINET.
7 - 2.5 PUMP MOTORS.
7 - 2.6 INTERNAL WIRING.
7 - 2.6.1 General requirements.
7 - 2.6.2 Conduit enclosures.
7 - 2.6.3 MIMS cable.
7 - 2.6.4 Wire-armoured cable.
7 - 2.6.5 Flexible cord.
7 - 2.7 TERMINAL ENCLOSURES.
7 - 2.8 EARTHING AND BONDING.
7 - 2.9 CABLING TO INTRINSICALLY SAFE EQUIPMENT.
7 - 2.10 ELECTRICAL POWER OUTLETS.
7 - 2.11 SEALING.
7 - 2.12 SAFETY DEVICES.
7 - 2.12.1 General.
7 - 2.12.2 Self-sealing nozzle.
7 - 2.12.3 Dispensing hose.
8 - 2.12.4 Control valves.
8 - 2.12.5 Hose protection.
8 - 2.12.6 Overspeed sensor.
8 - 2.12.7 Pump control.
8 - 2.13 INSTALLATION CONDITIONS.
8 - 2.13.1 General.
8 - 2.13.2 Excess flow valve.
8 - 2.13.3 Remote pump control.
8 - 2.13.4 Overspeed trip.
8 - SECTION 3. COMPLIANCE WITH STANDARDS
8 - 3.1 GENERAL REQUIREMENTS OF AS 3100.
8 - 3.2 SPECIFIC REQUIREMENTS OF THIS STANDARD.
8 - 3.3 COMPONENTS.
9 - SECTION 4. MARKING
9 - 4.1 MARKING.
9 - SECTION 5. TESTS
9 - 5.1 GENERAL.
9 - 5.2 TESTS FOR COMPLIANCE WITH AS 3100.
9 - 5.3 SURFACE TEMPERATURE TEST.
9 - 5.4 TEST OF CABINET.

Specifies requirements for the electrical systems of liquefied petroleum gas (LP gas) dispensing equipment including the electrical and hydraulic components. Includes requirements for internal wiring, terminal enclosures, earthing and bonding, and safety devices. Also specifies requirements for marking and testing.

This Standard specifies requirements for the electrical systems of liquefied petroleum gas (LP gas) dispensing equipment (referred to in this Standard as 'dispensing equipment') and for the electrical components and hydraulic components which may be used inside or outside the cabinet of such dispensing equipment.This Standard does not apply to dispensing equipment installed in private premises where LP gas is not sold.NOTE: Equipment complying with this Standard is suitable for use in driveway dispensing situations.The tests specified herein are intended as type tests to prove a particular design for compliance with this Standard.

Under Revision see DR 99900.
Under Revision see DR 99902