AS 5332:2019
Current
The latest, up-to-date edition.
Acoustics - Determination of sound power levels of noise sources - Guidelines for the use of basic standards
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
English
06-06-2019
Important note : Users cannot be edited or removed once added to your Multi user PDF.The objective of this Standard is to specify methods for determining the sound power level or sound energy level of a noise source from sound pressure levels measured in a reverberation test room.
| Committee |
EV-010
|
| DocumentType |
Standard
|
| ISBN |
978 1 76072 485 6
|
| Pages |
62
|
| PublisherName |
Standards Australia
|
| Status |
Current
|
| Supersedes |
This International Standard specifies methods for determining the sound power level or sound energy level of a noise source from sound pressure levels measured in a reverberation test room. The sound power level (or, in the case of noise bursts or transient noise emission, the sound energy level) produced by the noise source, in frequency bands of width one-third-octave, is calculated using those measurements, including corrections to allow for any differences between the meteorological conditions at the time and place of the test and those corresponding to a reference characteristic impedance. Measurement and calculation procedures are given for both a direct method and a comparison method of determining the sound power level and the sound energy level.
In general, the frequency range of interest includes the one-third-octave bands with mid-band frequencies from 100 Hz to 10 000 Hz. Guidelines for the application of the specified methods over an extended frequency range in respect to lower frequencies are given in Annex E. This International Standard is not applicable to frequency ranges above the 10 000 Hz one-third-octave band.
NOTE For higher frequencies, the methods specified in ISO 9295 can be used.
| Standards | Relationship |
| ISO 3741:2010 | Identical |
First published as AS 5332:2019.
| IEC 61672-1:2013 | Electroacoustics - Sound level meters - Part 1: Specifications |
| ISO 5725-1:1994 | Accuracy (trueness and precision) of measurement methods and results — Part 1: General principles and definitions |
| ISO 9295:2015 | Acoustics Determination of high-frequency sound power levels emitted by machinery and equipment |
| ISO/IEC Guide 98-3:2008 | Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995) |
| ISO 6926:2016 | Acoustics Requirements for the performance and calibration of reference sound sources used for the determination of sound power levels |
| ISO 5725-2:1994 | Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method |
| ISO 9296:2017 | Acoustics — Declared noise emission values of information technology and telecommunications equipment |
| ISO 9613-1:1993 | Acoustics Attenuation of sound during propagation outdoors Part 1: Calculation of the absorption of sound by the atmosphere |
| ISO 80000-8:2007 | Quantities and units Part 8: Acoustics |
| ISO 9614-2:1996 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 2: Measurement by scanning |
| ISO 9614-3:2002 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 3: Precision method for measurement by scanning |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| ISO 3747:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering/survey methods for use in situ in a reverberant environment |
| ISO 3740:2019 | Acoustics — Determination of sound power levels of noise sources — Guidelines for the use of basic standards |
| ISO 3743-1:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for small movable sources in reverberant fields Part 1: Comparison method for a hard-walled test room |
| ISO 7574-1:1985 | Acoustics — Statistical methods for determining and verifying stated noise emission values of machinery and equipment — Part 1: General considerations and definitions |
| ISO 3746:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
| ISO 5725-5:1998 | Accuracy (trueness and precision) of measurement methods and results — Part 5: Alternative methods for the determination of the precision of a standard measurement method |
| ISO 7574-2:1985 | Acoustics — Statistical methods for determining and verifying stated noise emission values of machinery and equipment — Part 2: Methods for stated values for individual machines |
| ISO 7574-3:1985 | Acoustics — Statistical methods for determining and verifying stated noise emission values of machinery and equipment — Part 3: Simple (transition) method for stated values for batches of machines |
| ISO 12001:1996 | Acoustics — Noise emitted by machinery and equipment — Rules for the drafting and presentation of a noise test code |
| ISO 5725-4:1994 | Accuracy (trueness and precision) of measurement methods and results Part 4: Basic methods for the determination of the trueness of a standard measurement method |
| ISO 3743-2:2018 | Acoustics — Determination of sound power levels of noise sources using sound pressure — Engineering methods for small, movable sources in reverberant fields — Part 2: Methods for special reverberation test rooms |
| IEC 60942:2003 | Electroacoustics - Sound calibrators |
| ISO/TR 25417:2007 | Acoustics Definitions of basic quantities and terms |
| ISO 3745:2012 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for anechoic rooms and hemi-anechoic rooms |
| IEC 61260:1995 | Electroacoustics - Octave-band and fractional-octave-band filters |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| ISO 354:2003 | Acoustics — Measurement of sound absorption in a reverberation room |
| ISO 3382-2:2008 | Acoustics Measurement of room acoustic parameters Part 2: Reverberation time in ordinary rooms |
| ISO 5725-3:1994 | Accuracy (trueness and precision) of measurement methods and results — Part 3: Intermediate measures of the precision of a standard measurement method |
| ISO 7574-4:1985 | Acoustics — Statistical methods for determining and verifying stated noise emission values of machinery and equipment — Part 4: Methods for stated values for batches of machines |
| ISO 5725-6:1994 | Accuracy (trueness and precision) of measurement methods and results — Part 6: Use in practice of accuracy values |
| ISO 9614-1:1993 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points |
| IEC 61183:1994 | Electroacoustics - Random-incidence and diffuse-field calibration of sound level meters |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.