ISO 3743-1:2010

Current

Current The latest, up-to-date edition.

Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for small movable sources in reverberant fields Part 1: Comparison method for a hard-walled test room

Available format(s): Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

Language(s): English, French

Published date: 21-09-2010

Publisher: International Organization for Standardization

Abstract - (Show below) - (Hide below)

ISO 3743-1:2010 specifies methods for determining the sound power level or sound energy level of a noise source by comparing measured sound pressure levels emitted by this source (machinery or equipment) mounted in a hard-walled test room, the characteristics of which are specified, with those from a calibrated reference sound source. The sound power level (or, in the case of noise bursts or transient noise emission, the sound energy level) produced by the noise source, in frequency bands of width one octave, is calculated using those measurements. The sound power level or sound energy level with frequency A-weighting applied is calculated using the octave-band levels.

The method specified in ISO 3743-1:2010 is suitable for all types of noise (steady, non-steady, fluctuating, isolated bursts of sound energy, etc.) defined in ISO 12001.

The noise source under test may be a device, machine, component or sub-assembly. The maximum size of the source depends upon the size of the room used for the acoustical measurements (see 4.2).

The test environment that is applicable for measurements made in accordance with ISO 3743-1:2010 is a hard-walled test room with prescribed acoustical characteristics.

Information is given on the uncertainty of the sound power levels and sound energy levels determined in accordance with ISO 3743-1:2010, for measurements made in frequency octave bands and for A-weighted frequency calculations performed on them. The uncertainty conforms to ISO 12001:1996, accuracy grade 2 (engineering grade).

General Product Information - (Show below) - (Hide below)

Development Note	Supersedes ISO/DIS 3743-1. (09/2010) Also numbered as ANSI S12.53/1. (04/2011)
Document Type	Standard
ISBN
Pages
Published
Publisher	International Organization for Standardization
Status	Current
Supersedes	ISO 3743-1:1994

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
GOST R ISO 3743-1 : 2013	Identical
NF EN ISO 3743-1 : 2012	Identical
NBN EN ISO 3743-1 : 2010	Identical
NEN EN ISO 3743-1 : 2010	Identical
NS EN ISO 3743-1 : 2010	Identical
PN EN ISO 3743-1 : 2011	Identical
SANS 3743-1 : 2ED 2012	Identical
SN EN ISO 3743-1:2011	Identical
AS 5333.1:2019	Identical
SS-EN ISO 3743-1:2010	Identical
UNE-EN ISO 3743-1:2011	Identical
BS EN ISO 3743-1:2009	Identical
EN ISO 3743-1:2010	Identical
DIN EN ISO 3743-1:2011-01	Identical
BS EN ISO 3743-1:2010	Identical
UNI EN ISO 3743-1 : 2010	Identical
BS ISO 3743-1 : 1994 AMD 8937	Identical
I.S. EN ISO 3743-1:2010	Identical

Standards Referenced By This Book - (Show below) - (Hide below)

CEI EN 60349-4 : 2014	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 4: PERMANENT MAGNET SYNCHRONOUS ELECTRICAL MACHINES CONNECTED TO AN ELECTRONIC CONVERTER
08/30193440 DC : 0	BS EN 60335-2-72 - HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-72: PARTICULAR REQUIREMENTS FOR AUTOMATIC MACHINES FOR FLOOR TREATMENT FOR COMMERCIAL AND INDUSTRIAL USE
I.S. EN 60335-2-75:2004	HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-75: PARTICULAR REQUIREMENTS FOR COMMERCIAL DISPENSING APPLIANCES AND VENDING MACHINES
CSA C22.2 No. 80601-2-35 : 2012	MEDICAL ELECTRICAL EQUIPMENT - PART 2-35: PARTICULAR REQUIREMENTS FOR THE BASIC SAFETY AND ESSENTIAL PERFORMANCE OF HEATING DEVICES USING BLANKETS, PADS OR MATTRESSES AND INTENDED FOR HEATING IN MEDICAL USE
I.S. EN 12639:2000	LIQUID PUMPS AND PUMP UNITS - NOISE TEST CODE - GRADE 2 AND GRADE 3 OF ACCURACY
BS EN 1870-19:2013	Safety of woodworking machines. Circular sawing machines Circular saw benches (with and without sliding table) and building site saws
09/30206358 DC : DRAFT SEP 2009	BS EN 1870-4 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 4: MULTI-BLADE RIP SAWING MACHINES WITH MANUAL LOADING AND/OR UNLOADING
I.S. EN 1870-18:2013	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 18: DIMENSION SAWS
01/202453 DC : DRAFT APRIL 2001	IEC 60034-9 ED.4 - ROTATING ELECTRICAL MACHINERY - PART 9: NOISE LIMITS
08/30178810 DC : DRAFT MAY 2008	BS EN 12750 - SAFETY OF WOODWORKING MACHINES - FOUR SIDED MOULDING MACHINES
I.S. EN 60335-2-79:2012	HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-79: PARTICULAR REQUIREMENTS FOR HIGH PRESSURE CLEANERS AND STEAM CLEANERS (IEC 60335-2-79:2012 (MOD))
DIN EN 12012-1:2015-05 (Draft)	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 1: SAFETY REQUIREMENTS FOR BLADE GRANULATORS
AAMI ISO 80601-2-35 : 2009	MEDICAL ELECTRICAL EQUIPMENT - PART 2-35: PARTICULAR REQUIREMENTS FOR THE BASIC SAFETY AND ESSENTIAL PERFORMANCE OF HEATING DEVICES USING BLANKETS, PADS OR MATTRESSES AND INTENDED FOR HEATING IN MEDICAL USE
DIN EN 16564 E : 2015	MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR BRIDGE TYPE SAWING/MILLING MACHINES, INCLUDED NUMERICAL CONTROL (NC/CNC) VERSIONS
12/30253910 DC : DRAFT JULY 2012	BS EN 1807-2 - SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES - LOG SAWING MACHINES
12/30257842 DC : 0	BS ISO 27327-2 - FANS - AIR CURTAIN UNITS - PART 2: LABORATORY METHODS OF TESTING FOR SOUND POWER
PREN 1870-3 : DRAFT 2012	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 3: DOWN CUTTING CROSS-CUT SAWS AND DUAL PURPOSE DOWN CUTTING CROSS-CUT SAWS/CIRCULAR SAW BENCHES
10/30233212 DC : 0	BS EN 848-3 - SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOLS - PART 3: NUMERICALLY CONTROLLED (NC) BORING AND ROUTING MACHINES
08/30182278 DC : 0	BS EN 1547:2001/A1 - INDUSTRIAL THERMOPROCESSING EQUIPMENT - NOISE TEST CODE FOR INDUSTRIAL THERMOPROCESSING EQUIPMENT INCLUDING ITS ANCILLARY HANDLING EQUIPMENT
DIN EN 16564:2015-04	Machines and plants for mining and tooling of natural stone - Safety - Requirements for bridge type sawing/milling machines, included numerical control (NC/CNC) versions
EN ISO 11202:2010	Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010)
12/30262897 DC : DRAFT JUNE 2012	BS EN 1674 - FOOD PROCESSING MACHINERY - DOUGH SHELTERS - SAFETY AND HYGIENE REQUIREMENTS
11/30237569 DC : 0	BS EN 1870-19 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 19: CIRCULAR SAW BENCHES (WITH AND WITHOUT SLIDING TABLE) AND BUILDING SITE SAWS
SMPTE EG 16 : 2014	MEASUREMENT METHODS FOR FILM AND DIGITAL MOTION-PICTURE CAMERA ACOUSTICAL NOISE - FIELD METHOD
BS EN 60335-2-67:2012 (published 2013-04)	Household and similar electrical appliances. Safety Particular requirements for floor treatment machines for commercial use
BS 848-2.2(2004) : 2004	INDUSTRIAL FANS - DETERMINATION OF FAN SOUND POWER LEVELS UNDER STANDARDIZED LABORATORY CONDITIONS - PART 2: REVERBERANT ROOM METHOD
16/30318928 DC : 0	BS EN ISO 19085-7 - WOODWORKING MACHINES - SAFETY - PART 7: SURFACE PLANING THICKNESS PLANING COMBINED SURFACE/THICKNESS PLANING MACHINES
09/30197984 DC : 0	BS EN 1807-2 - SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES - PART 2: LOG SAWING MACHINES
BS EN 60335-2-72:2012	Household and similar electrical appliances. Safety Particular requirements for floor treatment machines with or without traction drive, for commercial use
07/30151731 DC : 0	BS IEC 80601-2-35 - MEDICAL ELECTRICAL EQUIPMENT - PART 2-35: PARTICULAR REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE OF BLANKETS, PADS AND MATTRESSES, INTENDED FOR HEATING IN MEDICAL USE
PREN ISO 11200 : DRAFT 2012	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - GUIDELINES FOR THE USE OF BASIC STANDARDS FOR THE DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS (ISO/DIS 11200:2012)
CAN/CSA-C22.2 NO. 60335-2-72:2017	HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-72: PARTICULAR REQUIREMENTS FOR FLOOR TREATMENT MACHINES WITH OR WITHOUT TRACTION DRIVE, FOR COMMERCIAL USE
BS 848-2.1(2004) : 2004	INDUSTRIAL FANS - DETERMINATION OF FAN SOUND POWER LEVELS UNDER STANDARDIZED LABORATORY CONDITIONS - PART 1: GENERAL OVERVIEW
CEI EN 60335-2-67 : 2013	HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-67: PARTICULAR REQUIREMENTS FOR FLOOR TREATMENT MACHINES FOR COMMERCIAL USE
UNI EN 12012-4 : 2008	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 4: SAFETY REQUIREMENTS FOR AGGLOMERATORS
DIN EN 1807-1:2013-06	Safety of woodworking machines - Band sawing machines - Part 1: Table band saws and band re-saws
EEMUA 140 : 2014	NOISE PROCEDURE SPECIFICATION
I.S. EN ISO 3740:2000	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES - GUIDELINES FOR THE USE OF BASIC STANDARDS
I.S. EN 12102:2013	AIR CONDITIONERS, LIQUID CHILLING PACKAGES, HEAT PUMPS AND DEHUMIDIFIERS WITH ELECTRICALLY DRIVEN COMPRESSORS FOR SPACE HEATING AND COOLING - MEASUREMENT OF AIRBORNE NOISE - DETERMINATION OF THE SOUND POWER LEVEL
I.S. EN ISO 18217:2015	SAFETY OF WOODWORKING MACHINES - EDGE-BANDING MACHINES FED BY CHAIN(S) (ISO 18217:2015)
I.S. EN 1807-2:2013	SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES - PART 2: LOG SAWING MACHINES
BS EN 60335-2-69:2012	Household and similar electrical appliances. Safety Particular requirements for wet and dry vacuum cleaners, including power brush for commercial use
PREN 1870-12 : DRAFT 2011	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 12: PENDULUM CROSS-CUT SAWING MACHINES
I.S. EN 16564:2014	MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR BRIDGE TYPE SAWING/MILLING MACHINES, INCLUDED NUMERICAL CONTROL (NC/CNC) VERSIONS
I.S. EN 15571:2014	MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR SURFACE FINISHING MACHINES
BS EN 60335-2-75 : 2004	HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-75: PARTICULAR REQUIREMENTS FOR COMMERCIAL DISPENSING APPLIANCES AND VENDING MACHINES
I.S. EN 1829-1:2010	HIGH PRESSURE WATER JET MACHINES - SAFETY REQUIREMENTS - PART 1: MACHINES
I.S. EN 60034-9:2005	ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
BS EN 60704-2-13:2017	Household and similar electrical appliances. Test code for the determination of airborne acoustical noise Particular requirements for range hoods and other cooking fume extractors
UNE-EN 13141-11:2015	Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 11: Supply ventilation units
ISO 19085-1:2017	Woodworking machines Safety Part 1: Common requirements
BS EN 1870-6:2017	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 6: CIRCULAR SAWING MACHINES FOR FIRE WOOD
BS EN ISO 19085-1:2017	WOODWORKING MACHINES - SAFETY - PART 1: COMMON REQUIREMENTS (ISO 19085-1:2017)
UNE-EN ISO 19085-1:2018	Woodworking machines - Safety - Part 1: Common requirements (ISO 19085-1:2017)
ANSI/ASA S12.53 PART 2 : 1999(R2015)	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL, MOVABLE SOURCES IN REVERBERANT FIELDS - PART 2: METHODS FOR SPECIAL REVERBERATION TEST ROOMS
UNI EN 12102 : 2014	AIR CONDITIONERS, LIQUID CHILLING PACKAGES, HEAT PUMPS AND DEHUMIDIFIERS WITH ELECTRICALLY DRIVEN COMPRESSORS FOR SPACE HEATING AND COOLING - MEASUREMENT OF AIRBORNE NOISE - DETERMINATION OF THE SOUND POWER LEVEL
ISO 8579-1:2002	Acceptance code for gear units Part 1: Test code for airborne sound
DIN EN 1673:2010-10	Food processing machinery - Rotary rack ovens - Safety and hygiene requirements (includes Amendment A1:2009)
I.S. EN ISO 3743-2:2009	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL, MOVABLE SOURCES IN REVERBERANT FIELDS - PART 2: METHODS FOR SPECIAL REVERBERATION TESTS ROOMS
DIN EN ISO 9902-4 E : 2001	TEXTILE MACHINERY - NOISE TEST CODE - PART 4: YARN PROCESSING, CORDAGE AND ROPE MANUFACTURING MACHINERY (ISO 9902-4:2001 + AMD 1:2009 + AMD 2:2014)
DIN EN 1870-7:2013-01	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 7: SINGLE BLADE LOG SAWING MACHINES WITH INTEGRATED FEED TABLE AND MANUAL LOADING AND/OR UNLOADING
DIN EN 13355:2010-06	COATING PLANTS - COMBINED BOOTHS - SAFETY REQUIREMENTS
DIN EN 1870-12:2014-03	Safety of woodworking machines - Circular sawing machines - Part 12: Pendulum cross-cut sawing machines
DIN EN 15036-1:2006-12	Heating boilers - Test regulations for airborne noise emissions from heat generators - Part 1: Airborne noise emissions from heat generators
DIN EN 1870-16:2013-01	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 16: DOUBLE MITRE SAWING MACHINES FOR V CUTTING
DIN EN ISO 9902-1 E : 2001	TEXTILE MACHINERY - NOISE TEST CODE - PART 1: COMMON REQUIREMENTS (ISO 9902-1:2001 + AMD 1:2009 + AMD 2:2014)
DIN EN 13141-6:2015-02	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 6: EXHAUST VENTILATION SYSTEM PACKAGES USED IN A SINGLE DWELLING
DIN EN 12012-3:2010-02	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 3: SAFETY REQUIREMENTS FOR SHREDDERS
DIN EN ISO 11200:2014-10	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - GUIDELINES FOR THE USE OF BASIC STANDARDS FOR THE DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS (ISO 11200:2014)
DIN EN 1870-9:2013-01	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 9: DOUBLE BLADE CIRCULAR SAWING MACHINES FOR CROSS-CUTTING WITH INTEGRATED FEED AND WITH MANUAL LOADING AND/OR UNLOADING
DIN EN 1870-3:2015-02	Safety of woodworking machines - Circular sawing machines - Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches
I.S. EN 861:2007	SAFETY OF WOODWORKING MACHINES - SURFACE PLANING AND THICKNESSING MACHINES
BS EN ISO 3741:2009	Acoustics. Determination of sound power levels of noise sources using sound pressure. Precision methods for reverberation rooms
UNE-EN ISO 11200:2014	Acoustics - Noise emitted by machinery and equipment - Guidelines for the use of basic standards for the determination of emission sound pressure levels at a work station and at other specified positions (ISO 11200:2014)
UNE-EN 1870-4:2012	Safety of woodworking machines - Circular sawing machines - Part 4: Multiblade rip sawing machines with manual loading and/or unloading
ONORM EN 1218-1 : 2010	SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 1: SINGLE END TENONING MACHINES WITH SLIDING TABLE
BS EN ISO 11691:1997	ACOUSTICS - MEASUREMENT OF INSERTION LOSS OF DUCTED SILENCERS WITHOUT FLOW - LABORATORY SURVEY METHOD
UNE-EN 1870-7:2013	Safety of woodworking machines - Circular sawing machines - Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or unloading
BS EN 12984 : 2005	FOOD PROCESSING MACHINERY - PORTABLE AND/OR HAND-GUIDED MACHINES AND APPLIANCES WITH MECHANICALLY DRIVEN CUTTING TOOLS - SAFETY AND HYGIENE REQUIREMENTS
BS EN 859 : 2007	SAFETY OF WOODWORKING MACHINES - HAND FED SURFACE PLANING MACHINES
ISO 3746:2010	Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane
BS EN 1870-16:2012	Safety of woodworking machines. Circular sawing machines Double mitre sawing machines for V cutting
UNE-EN 60335-2-69:2013	Household and similar electrical appliances - Safety - Part 2-69: Particular requirements for wet and dry vacuum cleaners, including power brush for commercial use
ISO 11203:1995	Acoustics — Noise emitted by machinery and equipment — Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level
BS EN 1870-15:2012	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 15: MULTI-BLADE CROSS-CUT SAWING MACHINES WITH INTEGRATED FEED OF THE WORKPIECE AND MANUAL LOADING AND/OR UNLOADING
BS EN 1870-9:2012	Safety of woodworking machines. Circular sawing machines Double blade circular sawing machines for cross-cutting with integrated feed and with manual loading and/or unloading
BS EN ISO 11201:2010	Acoustics. Noise emitted by machinery and equipment. Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections
BS EN 14462:2015	SURFACE TREATMENT EQUIPMENT - NOISE TEST CODE FOR SURFACE TREATMENT EQUIPMENT INCLUDING ITS ANCILLARY HANDLING EQUIPMENT - ACCURACY GRADES 2 AND 3
BS EN 454:2014	FOOD PROCESSING MACHINERY - PLANETARY MIXERS - SAFETY AND HYGIENE REQUIREMENTS
BS EN ISO 11690-2:1997	ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE WORKPLACE MACHINERY - PART 2: NOISE CONTROL MEASURES
BS EN 1870-17 : 2012	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 17: MANUAL HORIZONTAL CUTTING CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS)
BS EN ISO 3743-2:1997	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL, MOVABLE SOURCES IN REVERBERANT FIELDS - PART 2: METHODS FOR SPECIAL REVERBERATION TESTS ROOMS
BS EN 1870-10:2013	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 10: SINGLE BLADE AUTOMATIC AND SEMI-AUTOMATIC UP-CUTTING CROSS-CUT SAWING MACHINES
BS EN 1673 : 2000	FOOD PROCESSING MACHINERY - ROTARY RACK OVENS - SAFETY AND HYGIENE REQUIREMENTS
I.S. EN 1673:2000	FOOD PROCESSING MACHINERY - ROTARY RACK OVENS - SAFETY AND HYGIENE REQUIREMENTS
I.S. EN ISO 11691:2009	ACOUSTICS - MEASUREMENT OF INSERTION LOSS OF DUCTED SILENCERS WITHOUT FLOW - LABORATORY SURVEY METHOD
UNI EN 1218-5 : 2010	SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 5: ONE SIDE PROFILING MACHINES WITH FIXED TABLE AND FEED ROLLERS OR FEED CHAIN
I.S. EN 13141-6:2014	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 6: EXHAUST VENTILATION SYSTEM PACKAGES USED IN A SINGLE DWELLING
I.S. EN 1870-16:2012	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 16: DOUBLE MITRE SAWING MACHINES FOR V-CUTTING
I.S. EN 454:2014	FOOD PROCESSING MACHINERY - PLANETARY MIXERS - SAFETY AND HYGIENE REQUIREMENTS
EN 12545:2000+A1:2009	Footwear, leather and imitation leather goods manufacturing machines - Noise test code - Common requirements
EN 1265:1999+A1:2008	Safety of machinery - Noise test code for foundry machines and equipment
EN 12012-4:2006+A1:2008	Plastics and rubber machines - Size reduction machines - Part 4: Safety requirements for agglomerators
EN 60704-2-11:1999	Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2-11: Particular requirements for electrically operated food preparation appliances
EN 13141-11:2015	Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 11: Supply ventilation units
NF EN ISO 11691 : 2009	ACOUSTICS - MEASUREMENT OF INSERTION LOSS OF DUCTED SILENCERS WITHOUT FLOW - LABORATORY SURVEY METHOD
EN 12639:2000/AC:2004	LIQUID PUMPS AND PUMP UNITS - NOISE TEST CODE - GRADE 2 AND GRADE 3 OF ACCURACY
DIN EN ISO 9902-1:2001-07	TEXTILE MACHINERY - NOISE TEST CODE - PART 1: COMMON REQUIREMENTS (ISO 9902-1:2001 + AMD 1:2009 + AMD 2:2014)
EN 13141-8:2014	Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 8: Performance testing of un-ducted mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for a single room
EN 60704-1:2010/A11:2012	HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - TEST CODE FOR THE DETERMINATION OF AIRBORNE NOISE - PART 1: GENERAL REQUIREMENTS (IEC 60704-1:2010)
DIN EN ISO 11691:2010-01	Acoustics - Measurement of insertion loss of ducted silencers without flow - Laboratory survey method (ISO 11691:1995); German version EN ISO 11691:2009
EN 13112:2002+A1:2009	Tannery machines - Splitting and bandknife shearing machines - Safety requirements
EN 12102:2013	Air conditioners, liquid chilling packages, heat pumps and dehumidifiers with electrically driven compressors for space heating and cooling - Measurement of airborne noise - Determination of the sound power level
EN 60034-9:2005/A1:2007	ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
EN 1218-3:2001+A1:2009	Safety of woodworking machines - Tenoning machines - Part 3: Hand fed tenoning machines with sliding table for cutting structural timbers
EN 13114:2002+A1:2009	Tannery machines - Rotating process vessels - Safety requirements
EN 1807-1:2013	Safety of woodworking machines - Band sawing machines - Part 1: Table band saws and band re-saws
DIN EN ISO 4871:2009-11	Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
EN 61096:1993/A1:1996	METHODS OF MEASURING THE CHARACTERISTICS OF REPRODUCING EQUIPMENT FOR DIGITAL AUDIO COMPACT DISCS
EN 62121:2001	Methods of measurement for minidisc recorders/players
EN 62777:2016	Quality evaluation method for the sound field of directional loudspeaker array system
EN 12012-2:2001+A2:2008	Plastics and rubber machines - Size reduction machines - Part 2: Safety requirements for strand pelletisers
EN 13113:2002+A1:2010	Tannery machines - Roller coating machines - Safety requirements
EN 12215:2004+A1:2009	Coating plants - Spray booths for application of organic liquid coating materials - Safety requirements
ONORM EN 1829-1 : 2010	HIGH PRESSURE WATER JET MACHINES - SAFETY REQUIREMENTS - PART 1: MACHINES
EN 13355:2004+A1:2009	Coating plants - Combined booths - Safety requirements
EN 1218-4:2004+A2:2009	Safety of woodworking machines - Tenoning machines - Part 4: Edge banding machines fed by chain(s)
EN 60335-2-79:2012	Household and similar electrical appliances - Safety - Part 2-79: Particular requirements for high pressure cleaners and steam cleaners
NBR IEC 60034-9 : 2011	ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
ONORM EN 13141-8 : 2014	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 8: PERFORMANCE TESTING OF UN-DUCTED MECHANICAL SUPPLY AND EXHAUST VENTILATION UNITS (INCLUDING HEAT RECOVERY) FOR MECHANICAL VENTILATION SYSTEMS INTENDED FOR A SINGLE ROOM
I.S. EN 12354-5:2009	BUILDING ACOUSTICS - ESTIMATION OF ACOUSTIC PERFORMANCE OF BUILDING FROM THE PERFORMANCE OF ELEMENTS - PART 5: SOUNDS LEVELS DUE TO THE SERVICE EQUIPMENT
ONORM EN 16583 : 2015	HEAT EXCHANGERS - HYDRONIC ROOM FAN COILS UNITS - DETERMINATION OF THE SOUND POWER LEVEL
15/30302620 DC : 0	BS EN ISO 19085-4 - WOODWORKING MACHINES - SAFETY - PART 4: VERTICAL PANEL CIRCULAR SAWING MACHINES
BS EN 60349-1:2010	Electric traction. Rotating electrical machines for rail and road vehicles Machines other than electronic converter-fed alternating current motors
12/30265270 DC : 0	BS EN 1870-6 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 6: CIRCULAR SAWING MACHINES FOR FIREWOOD AND DUAL PURPOSE CIRCULAR SAWING MACHINES FOR FIREWOOD/CIRCULAR SAW BENCHES, WITH MANUAL LOADING AND/OR UNLOADING
11/30237566 DC : 0	BS EN 1870-18 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 18: DIMENSION SAWS
UNE-EN 1870-13:2008	Safety of woodworking machines - Circular sawing machines - Part 13: Horizontal beam panel sawing machines
BS EN ISO 20361:2015	Liquid pumps and pump units. Noise test code. Grades 2 and 3 of accuracy
03/308040 DC : DRAFT MAY 2003	IEC 60704-2-2 ED. 2.0 - HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - TEST CODE FOR THE DETERMINATION OF AIRBORNE ACOUSTICAL NOISE - PART 2-2: PARTICULAR REQUIREMENTS FOR FAN HEATERS
UNI EN 1870-19 : 2014	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 19: CIRCULAR SAW BENCHES (WITH AND WITHOUT SLIDING TABLE) AND BUILDING SITE SAWS
04/30122794 DC : DRAFT SEP 2004	EN 15036-1 - HEATING BOILERS - TEST REGULATIONS FOR AIRBORNE NOISE EMISSIONS FROM HEAT GENERATORS - PART 1: AIRBORNE NOISE EMISSIONS FROM HEAT GENERATORS AT PLACE OF INSTALLATION
EN 1218-5:2004+A1:2009	Safety of woodworking machines - Tenoning machines - Part 5: One side profiling machines with fixed table and feed rollers or feed chain
BS EN 60349-4:2013	Electric traction. Rotating electrical machines for rail and road vehicles Permanent magnet synchronous electrical machines connected to an electronic converter
14/30302844 DC : 0	BS EN 60335-2-72 ED 3.0/AMD 1 - HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-72: PARTICULAR REQUIREMENTS FOR FLOOR TREATMENT MACHINES WITH OR WITHOUT TRACTION DRIVE FOR COMMERCIAL USE
04/30106849 DC : DRAFT MAY 2004	EN 1870-1 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 1: CIRCULAR SAW BENCHES (WITH AND WITHOUT SLIDING TABLE), DIMENSION SAWS AND BUILDING SITE SAWS
13/30267124 DC : 0	BS EN 13141-11 - VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 11: POSITIVE PRESSURE VENTILATION SYSTEMS
DIN EN ISO 11201:2010-10	Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010)
09/30198762 DC : 0	BS EN 1807-1 - SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES - PART 1: TABLE BAND SAWS AND BAND RE-SAWS
BS ISO 27327-2:2014	FANS - AIR CURTAIN UNITS - PART 2: LABORATORY METHODS OF TESTING FOR SOUND POWER
DIN EN 13141-11 E : 2015	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 11: SUPPLY VENTILATION UNITS
11/30237557 DC : 0	BS EN 1870-11 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 11: SEMI-AUTOMATIC AND AUTOMATIC HORIZONTAL CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS)
16/30341470 DC : 0	BS EN ISO 19085-10 - WOODWORKING MACHINES - SAFETY - PART 10: BUILDING SITE SAWS (CONTRACTOR SAWS)
12/30232434 DC : 0	BS EN 1870-5:2002+A1:2009 AMD 2 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 5: CIRCULAR SAWBENCHES/UP-CUTTING CROSS-CUT SAWING MACHINES
DIN EN 16583 E : 2015	HEAT EXCHANGERS - HYDRONIC ROOM FAN COILS UNITS - DETERMINATION OF THE SOUND POWER LEVEL
DIN EN 1807-2:2013-06	Safety of woodworking machines - Band sawing machines - Part 2: Log sawing machines; German version EN 1807-2:2013
BS EN 60335-2-79:2012	Household and similar electrical appliances. Safety Particular requirements for high pressure cleaners and steam cleaners
UNE-EN 691-1:2013	Safety of woodworking machines - Part 1: Common requirements
12/30271386 DC : 0	BS EN 12102 - AIR CONDITIONERS, LIQUID CHILLING PACKAGES, HEAT PUMPS AND DEHUMIDIFIERS WITH ELECTRICALLY DRIVEN COMPRESSORS FOR SPACE HEATING AND COOLING - MEASUREMENT OF AIRBORNE NOISE - DETERMINATION OF THE SOUND POWER LEVEL
PREN 1870-11 : DRAFT 2011	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 11: SEMI-AUTOMATIC AND AUTOMATIC HORIZONTAL CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS)
16/30335973 DC : 0	BS ISO 19085-9 - WOODWORKING MACHINES - SAFETY - PART 9: CIRCULAR SAW BENCHES (WITH AND WITHOUT SLIDING TABLE)
UNI EN ISO 10821 : 2010	INDUSTRIAL SEWING MACHINES - SAFETY REQUIREMENTS FOR SEWING MACHINES, UNITS AND SYSTEMS
DIN EN 16583:2015-10	Heat exchangers - Hydronic room fan coils units - Determination of the sound power level
UNI ISO 13347-1 : 2009	INDUSTRIAL FANS - DETERMINATION OF FAN SOUND POWER LEVELS UNDER STANDARDIZED LABORATORY CONDITIONS - PART 1: GENERAL OVERVIEW
11/30244804 DC : 0	BS EN 940:2009/A1 - SAFETY OF WOODWORKING MACHINES - COMBINED WOODWORKING MACHINES
BS ISO 15665:2003	Acoustics. Acoustic insulation for pipes, valves and flanges
DIN EN 1829-1:2010-05	High pressure water jet machines - Safety requirements - Part 1: Machines
07/30094858 DC : 0	BS ISO 3747 - ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING/SURVEY METHODS FOR USE IN SITU IN A REVERBERANT ENVIRONMENT
DIN EN ISO 20361:2016-05	LIQUID PUMPS AND PUMP UNITS - NOISE TEST CODE - GRADES 2 AND 3 OF ACCURACY (ISO 20361:2015)
PREN 13053 : DRAFT 2017	VENTILATION FOR BUILDINGS - AIR HANDLING UNITS - RATING AND PERFORMANCE FOR UNITS, COMPONENTS AND SECTIONS
PREN 14462 : DRAFT 2012	SURFACE TREATMENT EQUIPMENT - NOISE TEST CODE FOR SURFACE TREATMENT EQUIPMENT INCLUDING ITS ANCILLARY HANDLING EQUIPMENT - ACCURACY GRADES 2 AND 3
07/30161919 DC : 0	EN 940 - SAFETY OF WOODWORKING MACHINES - COMBINED WOODWORKING MACHINES
BS EN 15572:2015	Machines and plants for mining and tooling of natural stone. Safety. Requirements for edge finishing machines
04/301783 DC : DRAFT JAN 2004	EN 848-3 - SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 3: NUMERICALLY CONTROLLED (NC) BORING MACHINES AND ROUTING MACHINES
AAMI IEC 60601-2-50 : 2009	MEDICAL ELECTRICAL EQUIPMENT - PART 2-50: PARTICULAR REQUIREMENTS FOR THE BASIC SAFETY AND ESSENTIAL PERFORMANCE OF INFANT PHOTOTHERAPY EQUIPMENT
CEI EN 60335-2-69 : 2014	HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-69: PARTICULAR REQUIREMENTS FOR WET AND DRY VACUUM CLEANERS, INCLUDING POWER BRUSH, FOR COMMERCIAL USE
I.S. EN 60349-4:2013	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 4: PERMANENT MAGNET SYNCHRONOUS ELECTRICAL MACHINES CONNECTED TO AN ELECTRONIC CONVERTER (IEC 60349-4:2012 (EQV))
DIN EN ISO 18217 E : 2015	SAFETY OF WOODWORKING MACHINES - EDGEBANDING MACHINES FED BY CHAIN(S) (ISO 18217:2015)
NF EN 60034-9 : 2005 AMD 1 2007	ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
PREN 1870-6 : DRAFT 2012	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 6: CIRCULAR SAWING MACHINES FOR FIREWOOD AND DUAL PURPOSE CIRCULAR SAWING MACHINES FOR FIREWOOD/CIRCULAR SAW BENCHES, WITH MANUAL LOADING AND/OR UNLOADING
I.S. EN 1807-1:2013	SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES - PART 1: TABLE BAND SAWS AND BAND RE-SAWS
I.S. EN 62777:2016	QUALITY EVALUATION METHOD FOR THE SOUND FIELD OF DIRECTIONAL LOUDSPEAKER ARRAY SYSTEM
BS ISO 13347-1 : 2004	INDUSTRIAL FANS - DETERMINATION OF FAN SOUND POWER LEVELS UNDER STANDARDIZED LABORATORY CONDITIONS - PART 1: GENERAL OVERVIEW
BS EN 60268-5 : 2003	SOUND SYSTEM EQUIPMENT - PART 5: LOUDSPEAKERS
PREN 12102-2 : DRAFT 2016	AIR CONDITIONERS, LIQUID CHILLING PACKAGES, HEAT PUMPS AND DEHUMIDIFIERS WITH ELECTRICALLY DRIVEN COMPRESSORS - DETERMINATION OF THE SOUND POWER LEVEL - PART 2: HEAT PUMP WATER HEATERS
ISO 13347-2:2004	Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 2: Reverberant room method
ISO 3743-2:2018	Acoustics — Determination of sound power levels of noise sources using sound pressure — Engineering methods for small, movable sources in reverberant fields — Part 2: Methods for special reverberation test rooms
CSA C22.2 No. 80601-2-35 : 2012(R2016)	MEDICAL ELECTRICAL EQUIPMENT - PART 2-35: PARTICULAR REQUIREMENTS FOR THE BASIC SAFETY AND ESSENTIAL PERFORMANCE OF HEATING DEVICES USING BLANKETS, PADS OR MATTRESSES AND INTENDED FOR HEATING IN MEDICAL USE
CEI EN 60349-1 : 2012	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 1: MACHINES OTHER THAN ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
PREN 13141-6 : DRAFT 2012	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 6: EXHAUST VENTILATION SYSTEM PACKAGES USED IN A SINGLE DWELLING
EN 12042 : 2014 COR 2014	FOOD PROCESSING MACHINERY - AUTOMATIC DOUGH DIVIDERS - SAFETY AND HYGIENE REQUIREMENTS
I.S. EN 60268-5:2003	SOUND SYSTEM EQUIPMENT - PART 5: LOUDSPEAKERS
I.S. EN 16583:2015	HEAT EXCHANGERS - HYDRONIC ROOM FAN COILS UNITS - DETERMINATION OF THE SOUND POWER LEVEL
ANSI/ASA S12.54/ISO 3744 : 2011(R2016)	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR AN ESSENTIALLY FREE FIELD OVER A REFLECTING PLANE
I.S. EN 691-1:2012	SAFETY OF WOODWORKING MACHINES - PART 1: COMMON REQUIREMENTS
DIN EN 12042:2014-07	FOOD PROCESSING MACHINERY - AUTOMATIC DOUGH DIVIDERS - SAFETY AND HYGIENE REQUIREMENTS
UNI EN 12042 : 2014	FOOD PROCESSING MACHINERY - AUTOMATIC DOUGH DIVIDERS - SAFETY AND HYGIENE REQUIREMENTS
CSA C22.2 No. 80601-2-35 : 2012 : INC : COR 1 : 2012	MEDICAL ELECTRICAL EQUIPMENT - PART 2-35: PARTICULAR REQUIREMENTS FOR THE BASIC SAFETY AND ESSENTIAL PERFORMANCE OF HEATING DEVICES USING BLANKETS, PADS OR MATTRESSES AND INTENDED FOR HEATING IN MEDICAL USE
EN ISO 3740 : 2000	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES - GUIDELINES FOR THE USE OF BASIC STANDARDS
UNI EN 13141-7 : 2011	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 7: PERFORMANCE TESTING OF A MECHANICAL SUPPLY AND EXHAUST VENTILATION UNITS (INCLUDING HEAT RECOVERY) FOR MECHANICAL VENTILATION SYSTEMS INTENDED FOR SINGLE FAMILY DWELLINGS
BS EN ISO 3740:2001	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES - GUIDELINES FOR THE USE OF BASIC STANDARDS
ISO/TR 18569:2004	Safety of machinery Guidelines for the understanding and use of safety of machinery standards
NF EN ISO 3743-2 : 2009	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL, MOVABLE SOURCES IN REVERBERANT FIELDS - PART 2: METHODS FOR SPECIAL REVERBERATION TEST ROOMS
EN ISO 3746:2010	Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010)
IEC 60704-2-13:2016	Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2-13: Particular requirements for range hoods and other cooking fume extractors
I.S. EN 1870-6:2017	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 6: CIRCULAR SAWING MACHINES FOR FIRE WOOD
DIN EN 12215:2010-06	COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC LIQUID COATING MATERIALS - SAFETY REQUIREMENTS
ONORM EN 1218-5 : 2010	SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 5: ONE SIDE PROFILING MACHINES WITH FIXED TABLE AND FEED ROLLERS OR FEED CHAIN
DIN EN 1807:2010-02	SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES
DIN EN 13114:2010-03	Tannery machines - Rotating process vessels - Safety requirements (includes Amendment A1:2009)
DIN EN 1870-14:2012-06	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 14: VERTICAL PANEL SAWING MACHINES
DIN EN 1674:2015-12	FOOD PROCESSING MACHINERY - DOUGH SHEETERS - SAFETY AND HYGIENE REQUIREMENTS
DIN EN 12984:2011-02	Food processing machinery - Portable and/or hand-guided machines and appliances with mechanically driven cutting tools - Safety and hygiene requirements (includes Amendment A1:2010)
DIN EN 13112:2011-03	Tannery machines - Splitting and bandknife shearing machines - Safety requirements (includes Amendment A1:2009)
DIN EN 12301:2015-12 (Draft)	PLASTICS AND RUBBER MACHINES - CALENDERS - SAFETY REQUIREMENTS
DIN EN 12354-5:2009-10	Building acoustics - Estimation of acoustic performance of building from the performance of elements - Part 5: Sounds levels due to the service equipment
DIN EN 1870-10:2013-07	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 10: SINGLE BLADE AUTOMATIC AND SEMI-AUTOMATIC UP-CUTTING CROSS-CUT SAWING MACHINES
DIN EN 12981:2010-06	COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC POWDER COATING MATERIAL - SAFETY REQUIREMENTS
DIN EN 1870-13:2013-07	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 13: HORIZONTAL BEAM PANEL SAWING MACHINES
DIN EN 1265:2009-07	SAFETY OF MACHINERY - NOISE TEST CODE FOR FOUNDRY MACHINES AND EQUIPMENT
DIN EN 1870-8:2013-03	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 8: SINGLE BLADE EDGING CIRCULAR RIP SAWING MACHINES WITH POWER DRIVEN SAW UNIT AND MANUAL LOADING AND/OR UNLOADING
DIN EN 1218-1:2010-02	Safety of woodworking machines - Tenoning machines - Part 1: Single end tenoning machines with sliding table (includes Amendment A1:2009)
DIN EN 13141-8:2014-09	Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 8: Performance testing of un-ducted mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for a single room
DIN EN 14462 E : 2015	SURFACE TREATMENT EQUIPMENT - NOISE TEST CODE FOR SURFACE TREATMENT EQUIPMENT INCLUDING ITS ANCILLARY HANDLING EQUIPMENT - ACCURACY GRADES 2 AND 3
BS EN 1870-2:1999	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 2: HORIZONTAL BEAM PANEL SAWS AND VERTICAL PANEL SAWS
BS EN 12215 : 2004	COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC LIQUID COATING MATERIALS - SAFETY REQUIREMENTS
BS EN 12981 : 2005	COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC POWDER COATING MATERIAL - SAFETY REQUIREMENTS
ISO 4871:1996	Acoustics Declaration and verification of noise emission values of machinery and equipment
IEC 60349-2:2010	Electric traction - Rotating electrical machines for rail and road vehicles - Part 2: Electronic converter-fed alternating current motors
ISO 5136:2003	Acoustics — Determination of sound power radiated into a duct by fans and other air-moving devices — In-duct method
BS EN 13355 : 2004	COATING PLANTS - COMBINED BOOTHS - SAFETY REQUIREMENTS
BS EN 1870-7:2012	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 7: SINGLE BLADE LOG SAWING MACHINES WITH INTEGRATED FEED TABLE AND MANUAL LOADING AND/OR UNLOADING
BS EN 940 : 2009	SAFETY OF WOODWORKING MACHINES - COMBINED WOODWORKING MACHINES
UNE-EN 1870-10:2013	Safety of woodworking machines - Circular sawing machines - Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sawing machines
UNE-EN 60335-2-72:2013	Household and similar electrical appliances - Safety - Part 2-72: Particular requirements for floor treatment machines with or without traction drive, for commercial use
BS EN ISO 11546-1:1996	ACOUSTICS - DETERMINATION OF SOUND INSULATION PERFORMANCES OF ENCLOSURES - PART 1: MEASUREMENTS UNDER LABORATORY CONDITIONS (FOR DECLARATION PURPOSES)
ISO 11689:1996	Acoustics — Procedure for the comparison of noise-emission data for machinery and equipment
BS EN ISO 3744:2010	Acoustics. Determination of sound power levels and sound energy levels of noise sources using sound pressure. Engineering methods for an essentially free field over a reflecting plane
I.S. EN 1870-11:2013	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 11: SEMI AUTOMATIC HORIZONTAL CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS)
I.S. EN 1870-8:2012	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 8: SINGLE BLADE EDGING CIRCULAR RIP SAWING MACHINES WITH POWER DRIVEN SAW UNIT AND MANUAL LOADING AND/OR UNLOADING
I.S. EN 13114:2002	TANNERY MACHINES - ROTATING PROCESS VESSELS - SAFETY REQUIREMENTS
DIN EN 1218-4:2009-12	SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 4: EDGE BANDING MACHINES FED BY CHAIN(S)
DIN EN 12012-2:2010-02	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 2: SAFETY REQUIREMENTS FOR STRAND PELLETISERS
I.S. EN ISO 12001:2009	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - RULES FOR THE DRAFTING AND PRESENTATION OF A NOISE TEST CODE
I.S. EN 1870-10:2013	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 10: SINGLE BLADE AUTOMATIC AND SEMI-AUTOMATIC UP-CUTTING CROSS-CUT SAWING MACHINES
I.S. EN ISO 3747:2010	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING/SURVEY METHODS FOR USE IN SITU IN A REVERBERANT ENVIRONMENT
I.S. EN ISO 5136:2009	ACOUSTICS - DETERMINATION OF SOUND POWER RADIATED INTO A DUCT BY FANS AND OTHER AIR-MOVING DEVICES - IN-DUCT METHOD
I.S. EN 13113:2002	TANNERY MACHINES - ROLLER COATING MACHINES - SAFETY REQUIREMENTS
I.S. EN 12215:2004	COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC LIQUID COATING MATERIALS - SAFETY REQUIREMENTS
I.S. EN 1218-2:2004	SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 2: DOUBLE END TENONING AND/OR PROFILING MACHINES FED BY CHAIN OR CHAINS
UNI EN 1673 : 2010	FOOD PROCESSING MACHINERY - ROTARY RACK OVENS - SAFETY AND HYGIENE REQUIREMENTS
DIN EN 1870-1:1999-07	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 1: CIRCULAR SAW BENCHES (WITH AND WITHOUT SLIDING TABLE), DIMENSION SAWS AND BUILDING SITE SAWS
I.S. EN ISO 6926:2016	ACOUSTICS - REQUIREMENTS FOR THE PERFORMANCE AND CALIBRATION OF REFERENCE SOUND SOURCES USED FOR THE DETERMINATION OF SOUND POWER LEVELS (ISO 6926:2016)
UNI EN ISO 11691 : 2009	ACOUSTICS - MEASUREMENT OF INSERTION LOSS OF DUCTED SILENCERS WITHOUT FLOW - LABORATORY SURVEY METHOD
I.S. EN 1870-12:2013	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 12: PENDULUM CROSS-CUT SAWING MACHINES
I.S. EN ISO 3745:2012	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - PRECISION METHODS FOR ANECHOIC ROOMS AND HEMI-ANECHOIC ROOMS (ISO 3745:2012)
DIN EN 1218-3:2009-12	SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 3: HAND FED TENONING MACHINES WITH SLIDING TABLE FOR CUTTING STRUCTURAL TIMBERS
I.S. EN ISO 11204:2010	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS APPLYING ACCURATE ENVIRONMENTAL CORRECTIONS
ONORM EN 12042 : JUN 2014	FOOD PROCESSING MACHINERY - AUTOMATIC DOUGH DIVIDERS - SAFETY AND HYGIENE REQUIREMENTS
ONORM EN 16564 : 2015	MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR BRIDGE TYPE SAWING/MILLING MACHINES, INCLUDED NUMERICAL CONTROL (NC/CNC) VERSIONS
I.S. EN 1870-9:2012	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 9: DOUBLE BLADE CIRCULAR SAWING MACHINES FOR CROSSCUTTING WITH INTEGRATED FEED AND WITH MANUAL LOADING AND/OR UNLOADING
DIN EN ISO 11200:1996-07	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - GUIDELINES FOR THE USE OF BASIC STANDARDS FOR THE DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS (ISO 11200:2014)
I.S. EN 1870-3:2014	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 3: DOWN CUTTING CROSS-CUT SAWS AND DUAL PURPOSE DOWN CUTTING CROSS-CUT SAWS/CIRCULAR SAW BENCHES
I.S. EN 13141-8:2014	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 8: PERFORMANCE TESTING OF UN-DUCTED MECHANICAL SUPPLY AND EXHAUST VENTILATION UNITS (INCLUDING HEAT RECOVERY) FOR MECHANICAL VENTILATION SYSTEMS INTENDED FOR A SINGLE ROOM
I.S. EN 13141-7:2010	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 7: PERFORMANCE TESTING OF A MECHANICAL SUPPLY AND EXHAUST VENTILATION UNITS (INCLUDING HEAT RECOVERY) FOR MECHANICAL VENTILATION SYSTEMS INTENDED FOR SINGLE FAMILY DWELLINGS
EN 1673:2000+A1:2009	Food processing machinery - Rotary rack ovens - Safety and hygiene requirements
EN 16564:2014	Machines and plants for mining and tooling of natural stone - Safety - Requirements for bridge type sawing/milling machines, included numerical control (NC/CNC) versions
I.S. EN 12750:2013	SAFETY OF WOODWORKING MACHINES - FOUR SIDED MOULDING MACHINES
I.S. EN 1265:2000	SAFETY OF MACHINERY - NOISE TEST CODE FOR FOUNDRY MACHINES AND EQUIPMENT
DIN EN 13141-7:2011-01	Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 7: Performance testing of a mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for single family dwellings
DIN EN 12639:2000-06	LIQUID PUMPS AND PUMP UNITS - NOISE TEST CODE - GRADE 2 AND 3 OF ACCURACY
I.S. EN ISO 9902-4:2001	TEXTILE MACHINERY - NOISE TEST CODE - PART 4: YARN PROCESSING, CORDAGE AND ROPE MANUFACTURING MACHINERY (ISO 9902-4:2001)
I.S. EN ISO 3741:2010	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - PRECISION METHODS FOR REVERBERATION TEST ROOMS
I.S. EN 12981:2005	COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC POWDER COATING MATERIAL - SAFETY REQUIREMENTS
I.S. EN 1870-17:2012	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 17: MANUAL HORIZONTAL CUTTING CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS)
ONORM EN 15571 : 2015	MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR SURFACE FINISHING MACHINES
I.S. EN 453:2014	FOOD PROCESSING MACHINERY - DOUGH MIXERS - SAFETY AND HYGIENE REQUIREMENTS
EN ISO 11690-1 : 1996	ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE WORKPLACES CONTAINING MACHINERY - NOISE CONTROL STRATEGIES
DIN EN 1807:1999-10	SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES
I.S. EN 1870-15:2012	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 15: MULTIBLADE CROSS-CUT SAWING MACHINES WITH INTEGRATED FEED OF THE WORKPIECE AND MANUAL LOADING AND/OR UNLOADING
I.S. EN ISO 1680:2013	ACOUSTICS - TEST CODE FOR THE MEASUREMENT OF AIRBORNE NOISE EMITTED BY ROTATING ELECTRICAL MACHINES (ISO 1680:2013)
I.S. EN 1218-3:2002	SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 3: HAND FED TENONING MACHINES WITH SLIDING TABLE FOR CUTTING STRUCTURAL TIMBERS
I.S. EN 1218-5:2004	SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 5: ONE SIDE PROFILING MACHINES WITH FIXED TABLE AND FEED ROLLERS OR FEED CHAIN
EN ISO 6926:2016	Acoustics - Requirements for the performance and calibration of reference sound sources used for the determination of sound power levels (ISO 6926:2016)
I.S. EN 1870-14:2007	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 14: VERTICAL PANEL SAWING MACHINES
I.S. EN ISO 11546-1:2009	ACOUSTICS - DETERMINATION OF SOUND INSULATION PERFORMANCES OF ENCLOSURES - PART 1: MEASUREMENTS UNDER LABORATORY CONDITIONS (FOR DECLARATION PURPOSES)
I.S. EN 13355:2005	COATING PLANTS - COMBINED BOOTHS - SAFETY REQUIREMENTS
I.S. EN ISO 3744:2010	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR AN ESSENTIALLY FREE FIELD OVER A REFLECTING PLANE
I.S. EN ISO 11546-2:2009	ACOUSTICS - DETERMINATION OF SOUND INSULATION PERFORMANCES OF ENCLOSURES - PART 2: MEASUREMENTS IN SITU (FOR ACCEPTANCE AND VERIFICATION PURPOSES)
I.S. EN 12545:2000	FOOTWEAR, LEATHER AND IMITATION LEATHER GOODS MANUFACTURING MACHINES - NOISE TEST CODE - COMMON REQUIREMENTS
I.S. EN 12984:2006	FOOD PROCESSING MACHINERY - PORTABLE AND/OR HAND-GUIDED MACHINES AND APPLIANCES WITH MECHANICALLY DRIVEN CUTTING TOOLS - SAFETY AND HYGIENE REQUIREMENTS
I.S. EN 1674:2015	FOOD PROCESSING MACHINERY - DOUGH SHEETERS - SAFETY AND HYGIENE REQUIREMENTS
EN 15571:2014	Machines and plants for mining and tooling of natural stone - Safety - Requirements for surface finishing machines
EN 1829-1:2010	High pressure water jet machines - Safety requirements - Part 1: Machines
I.S. EN 1218-1:2000	SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 1: SINGLE END TENONING MACHINES WITH SLIDING TABLE
I.S. EN 940:2009	SAFETY OF WOODWORKING MACHINES - COMBINED WOODWORKING MACHINES
DIN EN ISO 10821:2013-02	INDUSTRIAL SEWING MACHINES - SAFETY REQUIREMENTS FOR SEWING MACHINES, UNITS AND SYSTEMS (ISO 10821:2005 + AMD 1:2009)
I.S. EN 12012-2:2001	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 2: SAFETY REQUIREMENTS FOR STRAND PELLETISERS
EN ISO 9902-6:2001/A2:2014	TEXTILE MACHINERY - NOISE TEST CODE - PART 6: FABRIC MANUFACTURING MACHINERY (ISO 9902-6:2001/AMD 2:2014)
ONORM EN 1673 : OCT 2010	FOOD PROCESSING MACHINERY - ROTARY RACK OVENS - SAFETY AND HYGIENE REQUIREMENTS
I.S. EN ISO 9614-3:2009	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND INTENSITY - PART 3: PRECISION METHOD FOR MEASUREMENT BY SCANNING
EN ISO 11691:2009	Acoustics - Measurement of insertion loss of ducted silencers without flow - Laboratory survey method (ISO 11691:1995)
I.S. EN 1870-7:2012	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 7: SINGLE BLADE LOG SAWING MACHINES WITH INTEGRATED FEED TABLE AND MANUAL LOADING AND/OR UNLOADING
I.S. EN 13112:2002	TANNERY MACHINES - SPLITTING AND BANDKNIFE SHEARING MACHINES - SAFETY REQUIREMENTS
DIN EN 12012-2:2004-03	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 2: SAFETY REQUIREMENTS FOR STRAND PELLETISERS
I.S. EN 14462:2015	SURFACE TREATMENT EQUIPMENT - NOISE TEST CODE FOR SURFACE TREATMENT EQUIPMENT INCLUDING ITS ANCILLARY HANDLING EQUIPMENT - ACCURACY GRADES 2 AND 3
I.S. EN ISO 11202:2010	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS APPLYING APPROXIMATE ENVIRONMENTAL CORRECTIONS
I.S. EN ISO 11201:2010	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS IN AN ESSENTIALLY FREE FIELD OVER A REFLECTING PLANE WITH NEGLIGIBLE ENVIRONMENTAL CORRECTIONS
I.S. EN ISO 3746:2010	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - SURVEY METHOD USING AN ENVELOPING MEASUREMENT SURFACE OVER A REFLECTING PLANE
I.S. EN 1870-5:2002	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 5: CIRCULAR SAWBENCHES/UP-CUTTING CROSS-CUT SAWING MACHINES
I.S. EN ISO 4871:2009	ACOUSTICS - DECLARATION AND VERIFICATION OF NOISE EMISSION VALUES OF MACHINERY AND EQUIPMENT
I.S. EN 1870-4:2012	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 4: MULTIBLADE RIP SAWING MACHINES WITH MANUAL LOADING AND/OR UNLOADING
I.S. EN ISO 9902-6:2001	TEXTILE MACHINERY - NOISE TEST CODE - PART 6: FABRIC MANUFACTURING MACHINERY (ISO 9902-6:2001)
UNI EN ISO 11689 : 1998	ACOUSTICS - PROCEDURE FOR THE COMPARISON OF NOISE-EMISSION DATA FOR MACHINERY AND EQUIPMENT
UNI EN 453 : 2014	FOOD PROCESSING MACHINERY - DOUGH MIXERS - SAFETY AND HYGIENE REQUIREMENTS
UNE-EN 60349-4:2013	Electric traction - Rotating electrical machines for rail and road vehicles - Part 4: Permanent magnet synchronous electrical machines connected to an electronic converter
CEI EN 60704-2-13 : 2012	HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - TEST CODE FOR THE DETERMINATION OF AIRBORNE ACOUSTICAL NOISE - PART 2-13: PARTICULAR REQUIREMENTS FOR RANGE HOODS AND OTHER COOKING FUME EXTRACTORS
EN 13141-7:2010	Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 7: Performance testing of a mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for single family dwellings
UNI EN ISO 3382-3 : 2012	ACOUSTICS - MEASUREMENT OF ROOM ACOUSTIC PARAMETERS - PART 3: OPEN PLAN OFFICES
UNI EN 691-1 : 2012	SAFETY OF WOODWORKING MACHINES - PART 1: COMMON REQUIREMENTS
ISO 11204:2010	Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections
BS ISO 15664:2001	Acoustics. Noise control design procedures for open plant
13/30289577 DC : 0	IEC 62777 - QUALITY EVALUATION METHOD FOR THE SOUND FIELD OF DIRECTIONAL LOUDSPEAKER ARRAY SYSTEM
09/30182105 DC : 0	BS EN 60349-2 - ELECTRICAL TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 2: ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
DIN EN ISO 18217:2015-12	Safety of woodworking machines - Edge-banding machines fed by chain(s) (ISO 18217:2015)
I.S. EN 848-1:2007	SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 1: SINGLE SPINDLE VERTICAL MOULDING MACHINES
BS ISO 8579-1:2002	Acceptance code for gear units Test code for airborne sound
10/30232428 DC : DRAFT DEC 2010	BS EN 1870-16 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 16: DOUBLE MITRE SAWING MACHINES FOR V CUTTING
BS EN 1870-18:2013	Safety of woodworking machines. Circular sawing machines Dimension saws
EN 1218-1:1999+A1:2009	Safety of woodworking machines - Tenoning machines - Part 1: Single end tenoning machines with sliding table
ANSI S12.53/2 : 1999	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL, MOVABLE SOURCES IN REVERBERANT FIELDS - PART 2: METHODS FOR SPECIAL REVERBERATION TEST ROOMS
DIN EN 1870-19 E : 2014	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 19: CIRCULAR SAW BENCHES (WITH AND WITHOUT SLIDING TABLE) AND BUILDING SITE SAWS
11/30251965 DC : 0	BS EN 453 - FOOD PROCESSING MACHINERY - DOUGH MIXERS - SAFETY AND HYGIENE REQUIREMENTS
12/30253907 DC : DRAFT JULY 2012	BS EN 1807-1 - SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES - TABLE BAND SAWS AND BAND RE-SAWS
DIN EN 15571:2015-03	Machines and plants for mining and tooling of natural stone - Safety - Requirements for surface finishing machines
10/30216264 DC : 0	BS EN 60335-2-79 - HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-79: PARTICULAR REQUIREMENTS FOR HIGH PRESSURE CLEANERS AND STEAM CLEANERS
BS EN 1807-2:2013	Safety of woodworking machines. Band sawing machines Log sawing machines
16/30345760 DC : 0	BS EN 12102-2 - AIR CONDITIONERS, LIQUID CHILLING PACKAGES, HEAT PUMPS AND DEHUMIDIFIERS WITH ELECTRICALLY DRIVEN COMPRESSORS - DETERMINATION OF THE SOUND POWER LEVEL - PART 2: HEAT PUMP WATER HEATERS
UNE-EN ISO 20361:2015	Liquid pumps and pump units - Noise test code - Grades 2 and 3 of accuracy (ISO 20361:2015)
10/30232425 DC : DRAFT DEC 2010	BS EN 1870-15 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 15: MULTI-BLADE CROSS-CUT SAWING MACHINES WITH INTEGRATED FEED OF THE WORKPIECE AND MANUAL LOADING AND/OR UNLOADING
10/30232422 DC : DRAFT DEC 2010	BS EN 1870-9 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 9: DOUBLE BLADE CIRCULAR SAWING MACHINES FOR CROSS-CUTTING WITH INTEGRATED FEED AND WITH MANUAL LOADING AND/OR UNLOADING
10/30232431 DC : DRAFT DEC 2010	BS EN 1870-17 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 17: MANUAL HORIZONTAL CUTTING CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (MANUAL RADIAL ARM SAWS)
14/30298371 DC : 0	BS EN 60335-2-68 ED 4.0 /A1 - HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-68: PARTICULAR REQUIREMENTS FOR SPRAY EXTRACTION MACHINES; FOR COMMERCIAL USE
BS PD ISO/TR 22100-1 : 2015	SAFETY OF MACHINERY - RELATIONSHIP WITH ISO 12100 - PART 1: HOW ISO 12100 RELATES TO TYPE-B AND TYPE-C STANDARDS
14/30297793 DC : 0	BS EN ISO 19085-3 - WOODWORKING MACHINES - SAFETY REQUIREMENTS - PART 3: NC BORING AND ROUTING MACHINES
DIN EN 1870-18:2013-08	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 18: DIMENSION SAWS
04/30126355 DC : DRAFT DEC 2004	ISO 20361 - LIQUID PUMPS AND PUMP UNITS - NOISE TEST CODE - GRADES 2 AND 3 OF ACCURACY
BS EN 60601-2-21 : 2009	MEDICAL ELECTRICAL EQUIPMENT - PART 2-21: PARTICULAR REQUIREMENTS FOR THE BASIC SAFETY AND ESSENTIAL PERFORMANCE OF INFANT RADIANT WARMERS (IEC 60601-2-21:2009)
04/30110326 DC : DRAFT APR 2004	EN 1870-17 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 17: MANUAL HORIZONTAL CUTTING CROSS-CUT CIRCULAR SAWING MACHINES WITH ONE SAW UNIT (MANUAL RADIAL ARM SAWS)
BS EN 1807-1:2013	SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES - PART 1: TABLE BAND SAWS AND BAND RE-SAWS
DIN EN 16430-1:2015-03	FAN ASSISTED RADIATORS, CONVECTORS AND TRENCH CONVECTORS - PART 1: TECHNICAL SPECIFICATIONS AND REQUIREMENTS
11/30237563 DC : 0	BS EN 1870-10 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 10: SINGLE BLADE AUTOMATIC AND SEMI-AUTOMATIC UP-CUTTING CROSS-CUT SAWING MACHINES
BS EN 60704-2-11:1999	Test code for the determination of airborne acoustical noise emitted by household and similar electrical appliances. Particular requirements Electrically operated food preparation appliances
UNE-EN 16564:2015	Machines and plants for mining and tooling of natural stone - Safety - Requirements for bridge type sawing/milling machines, included numerical control (NC/CNC) versions
ISO 27327-2:2014	Fans Air curtain units Part 2: Laboratory methods of testing for sound power
05/30133333 DC : DRAFT MAY 2005	EN 860 - SAFETY OF WOODWORKING MACHINES - ONE SIDE THICKNESS PLANING MACHINES
BS ISO 13347-2:2004	INDUSTRIAL FANS - DETERMINATION OF FAN SOUND POWER LEVELS UNDER STANDARDIZED LABORATORY CONDITIONS - PART 2: REVERBERANT ROOM METHOD
18/30369856 DC : 0	BS EN ISO 20361 - LIQUID PUMPS AND PUMPS UNITS - NOISE TEST CODE - GRADES 2 AND 3 OF ACCURACY
05/30133297 DC : DRAFT MAY 2005	EN 859 - SAFETY OF WOODWORKING MACHINES - HAND FED SURFACE PLANING MACHINES
04/301784 DC : DRAFT JAN 2004	EN 848-2 - SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 2: SINGLE SPINDLE HANDFED/INTEGRATED FED ROUNTING MACHINES
UNE-EN 16430-1:2015	Fan assisted radiators, convectors and trench convectors - Part 1: Technical specifications and requirements
BS EN 60704-1 : 2010	HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - TEST CODE FOR THE DETERMINATION OF AIRBORNE NOISE - PART 1: GENERAL REQUIREMENTS
UNE-EN 1807-1:2013	Safety of woodworking machines - Band sawing machines - Part 1: Table band saws and band re-saws
DIN EN 13141-11:2015-07	VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 11: SUPPLY VENTILATION UNITS
DD IEC/PAS 60704-2-15:2008	Household and similar electrical appliances. Test code for the determination of airborne acoustical noise Particular requirements for household food waste disposers
CEI EN 60349-2 : 2012	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 2: ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
UNE-EN 1870-6:2003	Safety of woodworking machines. Circular sawing machines. Part 6: Circular sawing machines for firewood and dual purpose circular sawing machines for firewood/circular saw benches, with manual loading and/or unloading.
IEC 60335-2-69:2016 RLV	Household and similar electrical appliances - Safety - Part 2-69: Particular requirements for wet and dry vacuum cleaners, including power brush, for commercial use
S.R. CEN ISO/TR 22100-1:2017	SAFETY OF MACHINERY - RELATIONSHIP WITH ISO 12100 - PART 1: HOW ISO 12100 RELATES TO TYPE-B AND TYPE-C STANDARDS (ISO/TR 22100-1:2015)
UNI EN 1807-2 : 2013	SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES - PART 2: LOG SAWING MACHINES
I.S. EN 15572:2015	MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR EDGE FINISHING MACHINES
ANSI S12.57 : 2011	ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING/SURVEY METHODS FOR USE IN SITU IN A REVERBERANT ENVIRONMENT
ISO 13261-1:1998	Sound power rating of air-conditioning and air-source heat pump equipment Part 1: Non-ducted outdoor equipment
UNE-EN 1829-1:2010	High pressure water jet machines - Safety requirements - Part 1: Machines
PREN 1870-10 : DRAFT 2011	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 10: SINGLE BLADE AUTOMATIC AND SEMI-AUTOMATIC UP-CUTTING CROSS-CUT SAWING MACHINES
UNE-EN 1870-14:2008	Safety of woodworking machines - Circular sawing machines - Part 14: Vertical panel sawing machines
UNE-EN 16583:2016	Heat exchangers - Hydronic room fan coils units - Determination of the sound power level
PREN 12102 : DRAFT 2012	AIR CONDITIONERS, LIQUID CHILLING PACKAGES, HEAT PUMPS AND DEHUMIDIFIERS WITH ELECTRICALLY DRIVEN COMPRESSORS FOR SPACE HEATING AND COOLING - MEASUREMENT OF AIRBORNE NOISE - DETERMINATION OF THE SOUND POWER LEVEL
PREN 60335-2-72 : DRAFT 2008	HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-72: PARTICULAR REQUIREMENTS FOR AUTOMATIC MACHINES FOR FLOOR TREATMENT FOR COMMERCIAL AND INDUSTRIAL USE
EN ISO 19085-1:2017/AC:2018	WOODWORKING MACHINES - SAFETY - PART 1: COMMON REQUIREMENTS (ISO 19085-1:2017)
UNI EN 12012-1 : 2008	PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 1: SAFETY REQUIREMENTS FOR BLADE GRANULATORS
I.S. EN 12301:2000	PLASTICS AND RUBBER MACHINES - CALENDERS - SAFETY REQUIREMENTS
I.S. EN 60335-2-68:2012	HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-68: PARTICULAR REQUIREMENTS FOR SPRAY EXTRACTION MACHINES, FOR COMMERCIAL USE (IEC 60335-2-68:2012 (MOD))
IEC 60335-2-69:2016	Household and similar electrical appliances - Safety - Part 2-69: Particular requirements for wet and dry vacuum cleaners, including power brush, for commercial use
IEC 60704-2-3:2017	Household and similar electrical appliances - Test code for the determination of airborne acoustical noise - Part 2-3: Particular requirements for dishwashers
DIN EN 1870-11:2014-02	SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINE