AS/NZS 4994.1:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Temporary edge protection General requirements
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
07-11-2023
English
22-09-2009
Important note : Users cannot be edited or removed once added to your Multi user PDF.Sets out requirements for the design, manufacture and testing of equipment that is intended to provide protection at the roof edge to workers installing, altering, repairing or removing cladding on housing and residential buildings having roof slopes of not more than 35 degrees to the horizontal.
| Committee |
BD-092
|
| DocumentType |
Standard
|
| ISBN |
0 7337 9226 X
|
| Pages |
37
|
| ProductNote |
Pending Revision indicates that as a result of the Aged Standards review process, the document needs updating. If no project proposal, meeting the quality criteria, is received within the 12 month timeframe, the document shall be withdrawn.
|
| PublisherName |
Standards Australia
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This Standard specifies requirements for the design, manufacture and testing of equipment that is intended to provide temporary edge protection for persons working on roofs of buildings having slopes not greater than 35° to the horizontal and for other exposed edges, prior to the installation of the permanent walling materials.NOTES:1 This Standard does not apply to the containment of materials on residential roofs.2 Edge protection is used on buildings that are being constructed, renovated, extended, altered or maintained.3 Where roof slopes exceed 35 degrees, roof edge protection should be specifically designed. In some instances it may be appropriate that some other form of restraint may be required to avoid risk of excessive impact.4 AS/NZS 4494.2 specifies requirements for the installation and dismantling of roof edge protection.5 AS/NZS 4494.3 specifies requirements for the installation and dismantling of edge protection of other edges prior to the installation of the permanent walling materials.
Originated as AS/NZS 4994.1(Int):2004.
Revised and redesignated AS/NZS 4994.1:2009.
| AS 1831-2007 | Ductile cast iron (Reconfirmed 2017) |
| AS/NZS 4680:2006 | Hot-dip galvanized (zinc) coatings on fabricated ferrous articles (Reconfirmed 2017) |
| AS/NZS 3679.1:1996 | Structural steel Hot-rolled bars and sections |
| AS 1866:1997 | Aluminium and aluminium alloys - Extruded rod, bar, solid and hollow shapes (Reconfirmed 2020) |
| AS 2074-2003 | Cast steels |
| AS/NZS 4600:2005 | Cold-formed steel structures |
| AS 1833-2002 | Austenitic cast iron |
| AS/NZS 1576.6:2000 | Scaffolding Metal tube-and-coupler scaffolding - Deemed to comply with AS/NZS 1576.3 |
| AS 1832-2007 | Malleable cast iron (Reconfirmed 2017) |
| AS/NZS 3678:1996 | Structural steel - Hot-rolled plates, floorplates and slabs |
| AS 4750-2003 | Electrogalvanized (zinc) coatings on ferrous hollow and open sections (Reconfirmed 2017) |
| AS 1720.1-1997 | Timber structures Design methods |
| AS/NZS 1594:2002 | Hot-rolled steel flat products (Reconfirmed 2016) |
| AS 1576.2-1991 | Scaffolding Couplers and accessories |
| AS 4100-1998 | Steel structures (Reconfirmed 2016) |
| AS 4100 SUPP 1-1999 | Steel structures - Commentary (Supplement to AS 4100-1998) |
| AS/NZS 4600 SUPP 1:1998 | Cold-formed steel structures - Commentary (Supplement to AS/NZS 4600:1996) |
| AS/NZS 1170.2:2002 | Structural design actions Wind actions |
| AS/NZS 1576.1:1995 | Scaffolding General requirements |
| AS 1874-2000 | Aluminium and aluminium alloys - Ingots and castings (Reconfirmed 2018) |
| AS 1163-1991 | Structural steel hollow sections |
| AS/NZS 1734:1997 | Aluminium and aluminium alloys - Flat sheet, coiled sheet and plate (Reconfirmed 2020) |
| AS/NZS 4792:2006 | Hot-dip galvanized (zinc) coatings on ferrous hollow sections, applied by a continuous or a specialized process (Reconfirmed 2017) |
| AS/NZS 1576.3:1995 | Scaffolding Prefabricated and tube-and-coupler scaffolding |
| AS/NZS 4994.4:2018 | Temporary edge protection Perimeter Protection Screens |
| AS/NZS 4994.2:2009 | Temporary edge protection Roof edge protection - Installation and dismantling |
| AS 1576.6:2020 | Scaffolding Metal tube-and-coupler scaffolding - Deemed to conform to AS/NZS 1576.1 |
| AS/NZS 4994.3:2010 | Temporary edge protection Installation and dismantling for edges other than roof edges |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.