![header thumbnail](/images/publishers\astm_cover.gif)
ASTM B 152/B152M : 2013 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar
08-05-2020
English
15-01-2013
CONTAINED IN VOL. 02.01, 2017 Describes the requirements for copper sheet, strip, plate, and rolled bar.
Committee |
B 05
|
DevelopmentNote |
Supersedes ASTM B 152. (06/2001)
|
DocumentType |
Redline
|
Pages |
8
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1This specification2 establishes the requirements for copper sheet, strip, plate, and rolled bar produced from the following coppers.
Copper | Previous | |
C10100B | OFE | Oxygen-free electronic |
C10200B | OF | Oxygen-free without residual |
C10300 | ... | Oxygen-free extra low phosphorus |
C10400, C10500, C10700 | OFS | Oxygen-free, silver bearing |
C10800 | ... | Oxygen-free low phosphorus |
C10910 | ... | Low oxygen |
ETP, | ||
C11300, C11400, C11600B | STP | Silver bearing tough pitch |
C12000 | DLP | Phosphorized, low residual phos- |
C12200B | DHP | Phosphorized, high residual phos- |
C12300 | DPS | Phosphorized, silver bearing |
C14200 | DPA | Phosphorus deoxidized, arsenical |
C14420 | ... | Tin bearing tellurium copper |
C14530 | ... | Tin tellurium bearing copper |
_______________ |
Plates for locomotive fireboxes are defined in Specification B11.
Flat copper products with finished (rolled or drawn) edges (flat wire and strip) are defined in Specification B272.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3The following safety hazards caveat only pertains to the test method portion, Section 13 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM C 665 : 2017 : REDLINE | Standard Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing |
A-A-52470 Revision A:2011 | FILTER, FLUID, PRESSURE AND FILTER ELEMENT, FLUID, PRESSURE-AUTOMOTIVE FUEL (45 GPH FILTRATION) |
A-A-52444 Revision A:2011 | Gaskets: Combination of Metal and Nonasbestos Facing Material (Metric) |
MIL-PRF-46002 Revision D:2010 | PRESERVATIVE OIL, CONTACT AND VOLATILE CORROSION-INHIBITED |
MIL-DTL-39030 Revision F:2014 | DUMMY LOADS, ELECTRICAL, COAXIAL AND STRIPLINE, GENERAL SPECIFICATION FOR |
MIL-DTL-21604 Revision G:2017 | Switches, Rotary, Multipole and Selector, General Specification for |
MIL-DTL-28830 Revision F:2016 | CABLE, RADIO FREQUENCY, COAXIAL, SEMIRIGID, CORRUGATED OUTER CONDUCTOR, GENERAL SPECIFICATION FOR |
MIL-DTL-17813 Revision H:2009 | Expansion Joints, Pipe, Metallic Bellows, General Specification for |
ASTM C 739 : 2017 : REDLINE | Standard Specification for Cellulosic Fiber Loose-Fill Thermal Insulation |
ASTM D 3658 : 2001 : R2008 | Standard Test Method for Determining the Torque Strength of Ultraviolet (UV) Light-Cured Glass/Metal Adhesive Joints |
ASTM F 2798 : 2009 | Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications |
ASTM D 3658 : 2001 : R2016 | Standard Test Method for Determining the Torque Strength of Ultraviolet (UV) Light-Cured Glass/Metal Adhesive Joints |
ASTM F 375 : 1989 : R2010 | Standard Specification for Integrated Circuit Lead Frame Material |
ASTM F 2798 : 2009 : R2018 | Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications |
NFPA 1977 : 2016 | PROTECTIVE CLOTHING AND EQUIPMENT FOR WILDLAND FIRE FIGHTING |
MIL-PRF-39012 Revision F:2014 | CONNECTORS, COAXIAL, RADIO FREQUENCY, GENERAL SPECIFICATION FOR |
MIL B 18 : F | BATTERIES, NON-RECHARGEABLE, DRY |
MIL STD 11991 : A | GENERAL STANDARD FOR PARTS, MATERIALS, AND PROCESSES |
MIL-DTL-12606 Revision E:2000 | LOUDSPEAKER, PERMANENT MAGNET (UNENCASED, 3-INCH AND 4-INCH DIAMETER CONE, 2-WATT; FUNGUS-, AND IMMERSION-RESISTANT), TYPE LS-445/U, M12606-01, AND M12606-02 |
W-F-1814 Revision D:2013 | FUSES, CARTRIDGE, HIGH-INTERRUPTING CAPACITY |
MIL-DTL-10911 Revision E:2012 | LOUDSPEAKERS, PERMANENT MAGNET, (UNENCASED, 2.5-, 3-, 4-, 5-, 6-, 8-, 10-, AND 12-INCH DIAMETER CONES), GENERAL SPECIFICATION FOR |
MIL-PRF-63460 Revision F:2017 | Cleaner, Lubricant, and Preservative for Weapons and Weapons Systems |
MIL-DTL-24749 Revision B:2014 | GROUNDING STRAPS AND BOSSES, ELECTROMAGNETIC |
ASTM D 3528 : 1996 | Standard Test Method for Strength Properties of Double Lap Shear Adhesive Joints by Tension Loading |
MIL-DTL-85-3 Revision D:2012 | WAVEGUIDES, RIGID, RECTANGULAR (MILLIMETER WAVELENGTH) |
MIL-PRF-81705 Revision E:2009 | Barrier Materials, Flexible, Electrostatic Discharge Protective, Heat-Sealable |
MIL-DTL-28839 Revision B:2013 | Waveguides, Elliptical General Specification for |
ASTM F 375 : 1989 : R2015 | Standard Specification for Integrated Circuit Lead Frame Material |
ASTM D 3658 : 2001 | Standard Test Method for Determining the Torque Strength of Ultraviolet (UV) Light-Cured Glass/Metal Adhesive Joints |
ASTM D 7095 : 2017 : REDLINE | Standard Test Method for Rapid Determination of Corrosiveness to Copper from Petroleum Products Using a Disposable Copper Foil Strip |
ASTM D 4857 : 2012 : REDLINE | Standard Test Method for Determination of the Ability of Lubricants to Minimize Ring Sticking and Piston Deposits in Two-Stroke-Cycle Gasoline Engines Other Than Outboards |
ASTM F 375 : 1989 : R2005 | Standard Specification for Integrated Circuit Lead Frame Material |
ASTM D 3165 : 2007 | Standard Test Method for Strength Properties of Adhesives in Shear by Tension Loading of Single-Lap-Joint Laminated Assemblies |
ASTM F 68 : 2016 : REDLINE | Standard Specification for Oxygen-Free Copper in Wrought Forms for Electron Devices |
ASTM D 345 : 2002 | Side bearings of the freight wagon bogies. General specifications |
UNE-EN ISO 4404-1:2012 | Petroleum and related products - Determination of the corrosion resistance of fire-resistant hydraulic fluids - Part 1: Water-containing fluids (ISO 4404-1:2012) |
ISO 4404-1:2012 | Petroleum and related products — Determination of the corrosion resistance of fire-resistant hydraulic fluids — Part 1: Water-containing fluids |
I.S. EN ISO 4404-1:2012 | PETROLEUM AND RELATED PRODUCTS - DETERMINATION OF THE CORROSION RESISTANCE OF FIRE-RESISTANT HYDRAULIC FLUIDS - PART 1: WATER-CONTAINING FLUIDS (ISO 4404-1:2012) |
ASME PV CODE 2C : 2017 | BOILER AND PRESSURE VESSEL CODE - MATERIALS - SPECIFICATIONS FOR WELDING RODS, ELECTRODES, AND FILLER METALS |
ASME B31.3:2016 | PROCESS PIPING |
MIL-DTL-14055 Revision G:2014 | CUP, HYDRAULIC BRAKE ACTUATING CYLINDER: SYNTHETIC RUBBER |
MIL-STD-1310 Revision H:2009 | SHIPBOARD BONDING, GROUNDING, AND OTHER TECHNIQUES FOR ELECTROMAGNETIC COMPATIBILITY, ELECTROMAGNETIC PULSE (EMP) MITIGATION, AND SAFETY |
MIL-PRF-55339 Revision C:2005 | Adapters, Connectors, Coaxial, Radio Frequency, (Between Series and within Series), General Specification for |
MIL-DTL-3954 Revision D:2015 | DUMMY LOADS, ELECTRICAL, WAVEGUIDE, GENERAL SPECIFICATION FOR |
ASTM B 248 : 2017 : REDLINE | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar |
MIL-DTL-2 Revision G:2006 | VALVES, CYLINDER, GAS (FOR COMPRESSED OR LIQUEFIED GASES), GENERAL SPECIFICATION FOR |
MIL-PRF-22019 Revision E:2006 | BARRIER MATERIALS, TRANSPARENT, FLEXIBLE, SEALABLE, VOLATILE CORROSION INHIBITOR TREATED |
ASTM B 506 : 2016 : REDLINE | Standard Specification for Copper-Clad Stainless Steel Sheet and Strip for Building Construction |
GOST R 52714:2018 | Motor gasolines. Determination of individual and group hydrocarbon composition by capillary gas сhromatography method |
ASTM C 764 : 2017 : REDLINE | Standard Specification for Mineral Fiber Loose-Fill Thermal Insulation |
ASTM F 2798 : 2009 : R2014 : EDT 1 | Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications |
ASTM D 3528 : 1996 : R2016 | Standard Test Method for Strength Properties of Double Lap Shear Adhesive Joints by Tension Loading |
DIN EN ISO 4404-1:2012-10 | PETROLEUM AND RELATED PRODUCTS - DETERMINATION OF THE CORROSION RESISTANCE OF FIRE-RESISTANT HYDRAULIC FLUIDS - PART 1: WATER-CONTAINING FLUIDS (ISO 4404-1:2012) |
DIN EN ISO 4404-1 E : 2012 | PETROLEUM AND RELATED PRODUCTS - DETERMINATION OF THE CORROSION RESISTANCE OF FIRE-RESISTANT HYDRAULIC FLUIDS - PART 1: WATER-CONTAINING FLUIDS (ISO 4404-1:2012) |
ICC IPC CODE & COMMENTARY : 2015 | IPC® Code and Commentary |
MIL-B-49030 Revision A:2010 | BATTERIES, DRY (ALKALINE) |
ICC 2012 INTERNATIONAL PLUMBING CODE : 2012 | INTERNATIONAL PLUMBING CODE (INCLUDES IPSDC) |
UNI EN ISO 4404-1 : 2013 | PETROLEUM AND RELATED PRODUCTS - DETERMINATION OF THE CORROSION RESISTANCE OF FIRE-RESISTANT HYDRAULIC FLUIDS - PART 1: WATER-CONTAINING FLUIDS |
AWS A5.6/A5.6M : 2008 | SPECIFICATION FOR COPPER AND COPPER-ALLOY ELECTRODES FOR SHIELDED METAL ARC WELDING |
ASTM B 753 : 2007 | Standard Specification for Thermostat Component Alloys |
NACE TM 02 08 : 2013 | LABORATORY TEST TO EVALUATE THE VAPOR-INHIBITING ABILITY OF VOLATILE CORROSION INHIBITOR MATERIALS FOR TEMPORARY PROTECTION OF FERROUS METAL SURFACES |
MIL-DTL-22931 Revision D:2013 | CABLES, RADIO FREQUENCY, SEMIRIGID, COAXIAL, SEMI-AIR-DIELECTRIC, GENERAL SPECIFICATION FOR |
ASTM D 4858 : 2013 : REDLINE | Standard Test Method for Determination of the Tendency of Lubricants to Promote Preignition in Two-Stroke-Cycle Gasoline Engines |
MIL-DTL-24558 Revision B:2011 | TERMINAL BOXES, CONNECTION, FOR ELECTRICAL AND ELECTRONIC SYSTEMS, GENERAL SPECIFICATION FOR |
MIL-PRF-49142 Revision B:2004 | CONNECTOR, TRIAXIAL, RADIO FREQUENCY, GENERAL SPECIFICATION FOR |
ASTM B 753 : 2007 : R2013 | Standard Specification for Thermostat Component Alloys |
ASTM D 4863 : 2013 : REDLINE | Standard Test Method for Determination of Lubricity of Two-Stroke-Cycle Gasoline Engine Lubricants |
10/30196081 DC : 0 | BS ISO 4404-1 - PETROLEUM AND RELATED PRODUCTS - DETERMINATION OF THE CORROSION RESISTANCE OF FIRE-RESISTANT HYDRAULIC FLUIDS - PART 1: WATER-CONTAINING FLUIDS |
ASTM D 3528 : 1996 : R2002 | Standard Test Method for Strength Properties of Double Lap Shear Adhesive Joints by Tension Loading |
ASTM F 375 : 1989 : R1999 | Standard Specification for Integrated Circuit Lead Frame Material |
A-A-59935-2 Base Document:2013 | Conical Seals, Crush, 37 Degree Flared Tube Fitting, Copper |
DSCC 85115 : E | CONTACT ASSEMBLY, ELECTRICAL |
ASTM E 746 : 2018 : REDLINE | Standard Practice for Determining Relative Image Quality Response of Industrial Radiographic Imaging Systems |
ASTM D 3433 : 1999 | Standard Test Method for Fracture Strength in Cleavage of Adhesives in Bonded Metal Joints |
EN ISO 4404-1:2012 | Petroleum and related products - Determination of the corrosion resistance of fire-resistant hydraulic fluids - Part 1: Water-containing fluids (ISO 4404-1:2012) |
ASTM B 753 : 2007 : R2018 | Standard Specification for Thermostat Component Alloys |
A-A-59935-6 Base Document:2013 | Conical Seals, Crush, 37 Degree Flared Tube Fitting, Serrated |
MIL-DTL-28754-67 Revision A:2016 | CONNECTORS, ELECTRICAL, MODULAR, CONNECTOR FRAME, TYPE 4, DOUBLE SPAN, CENTER |
NFPA 197 : 2018 | Standard on Protective Ensembles for Structural Fire Fighting and Proximity Fire Fighting |
MIL-DTL-15659 Revision J:2003 | TERMINAL, LUG: SOLDER, COPPER AND PHOSPHOR BRONZE |
MIL-DTL-28754-70 Revision A:2015 | CONNECTORS, ELECTRICAL, MODULAR, CONNECTOR FRAME, TYPE 4, SINGLE SPAN, CENTER |
MIL-DTL-28754-68 Revision A:2015 | CONNECTORS, ELECTRICAL, MODULAR, CONNECTOR FRAME, TYPE 4, DOUBLE SPAN, T-DIP |
VV-C-846 Revision D:2010 | CUTTING FLUIDS: EMULSIFIABLE OILS |
MIL DTL 5372/1 : B | FUSE, LIMITER TYPE ENCLOSED LINK, 1-60 AMPERE |
ASTM B 248M : 2017 : REDLINE | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar (Metric) |
MIL-DTL-85054 Revision D:2010 | CORROSION PREVENTIVE COMPOUND, WATER-DISPLACING, TRANSPARENT (FORMERLY AMLGUARD) |
ASTM D 3433 : 1999 : R2012 | Standard Test Method for Fracture Strength in Cleavage of Adhesives in Bonded Metal Joints |
SAE AS 1241 : 2016 | FIRE RESISTANT PHOSPHATE ESTER HYDRAULIC FLUID FOR AIRCRAFT |
ASTM B 813 : 2016 : REDLINE | Standard Specification for Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube |
SAE AS 81824 : 2016 | SPLICE, ELECTRIC, CRIMP, COPPER, ENVIRONMENT RESISTANT |
ASTM D 3433 : 1999 : R2005 | Standard Test Method for Fracture Strength in Cleavage of Adhesives in Bonded Metal Joints |
ASTM D 3528 : 1996 : R2008 | Standard Test Method for Strength Properties of Double Lap Shear Adhesive Joints by Tension Loading |
ASTM D 3165 : 2007 : R2014 | Standard Test Method for Strength Properties of Adhesives in Shear by Tension Loading of Single-Lap-Joint Laminated Assemblies |
BS EN ISO 4404-1:2012 | Petroleum and related products. Determination of the corrosion resistance of fire-resistant hydraulic fluids Water-containing fluids |
MIL-DTL-18714 Revision F:2012 | PRIMER, ELECTRIC, MARK 45 MOD 1 |
ASME B31.5 : 2016 | REFRIGERATION PIPING AND HEAT TRANSFER COMPONENTS |
ASME B31.3 SPANISH : 2010 | PROCESS PIPING |
ASTM B 224 : 2016 : REDLINE | Standard Classification of Coppers |
ASTM E 8M : 2004 | Standard Test Methods for Tension Testing of Metallic Materials [Metric] (Withdrawn 2008) |
ASTM B 370 : 2012 : REDLINE | Standard Specification for Copper Sheet and Strip for Building Construction |
ASTM E 527 : 2016 : REDLINE | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
ASTM B 846 : 2011-07 | TERMINOLOGY FOR COPPER AND COPPER ALLOYS |
ASTM B 248M : 2017 : REDLINE | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar (Metric) |
ASTM E 8 : 2004 | Standard Test Methods for Tension Testing of Metallic Materials |
ASME PV CODE SET : 2017 | BOILER AND PRESSURE VESSEL CODE - COMPLETE SET |
ASTM B 193 : 2016 : REDLINE | Standard Test Method for Resistivity of Electrical Conductor Materials |
ASTM B 248 : 2017 : REDLINE | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar |
ASTM B 216 : 2016 : REDLINE | Standard Specification for Tough-Pitch Fire-Refined Copper—Refinery Shapes |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.