ASTM B 557M : 2015 : REDLINE
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric)
Available format(s)
PDF
Language(s)
English
Published date
29-10-2015
Superseded date
29-10-2015
€75.83
Excluding VAT
CONTAINED IN VOL. 02.02, 2015 Specifies the tension testing of wrought and cast aluminum- and magnesium-alloy products, excepting aluminum foil, and are derived from Test Methods E 8M, which cover the tension testing of all metallic materials.
| Committee |
B 07
|
| DocumentType |
Redline
|
| Pages |
16
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
1.1These test methods cover the tension testing of wrought and cast aluminum- and magnesium-alloy products, with the exception of aluminum foil,2 and are derived from Test Methods E8M, which cover the tension testing of all metallic materials.
Note 1:These metric test methods are the equivalents of those in Test Methods B557, and are compatible in technical content except for the requirement of longer gage lengths for round specimens.
Note 2:Foil is sheet metal less than 0.20 mm thick. There is an overlap in the thickness range 0.15 to 0.20 mm defined for foil and sheet. Sheet products in this thickness range are supplied to sheet product specifications and foil products in this thickness range are supplied to foil product specifications. Exceptions to the provisions of these test methods may need to be made in individual specifications or test methods for a particular material.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM B 247M : 2015 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings (Metric) |
| 14/30291911 DC : 0 | BS ISO 6362-2 - WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS - EXTRUDED RODS/BARS, TUBES AND PROFILES - PART 2: MECHANICAL PROPERTIES |
| SAE AMS4302C | Aluminum Alloy, Laminated Sheet, Aramid Fiber Reinforced 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (7475-T761) 3, 5, 7, or 9 Ply |
| SAE AMS4210K | Aluminum Alloy, Castings 5.0Si - 1.2Cu - 0.50Mg (355.0-T51) Precipitation Heat Treated |
| ASTM B 928/B928M : 2015 : REDLINE | Standard Specification for High Magnesium Aluminum-Alloy Products for Marine Service and Similar Environments |
| SAE AMS4284K | Aluminum Alloy Castings, Permanent Mold 7.0Si - 0.30Mg (356.0-T6) Solution and Precipitation Heat Treated |
| SAE AMS4223E | Aluminum Alloy, Castings 4.5Cu - 0.70Ag - 0.30Mn - 0.25Mg - 0.25Ti (A201.0-T4) Solution Heat Treated and Naturally Aged |
| ASTM B 398/B398M : 2015 : REDLINE | Standard Specification for Aluminum-Alloy 6201-T81 and 6201-T83 Wire for Electrical Purposes |
| ASTM B 491/B491M : 2015 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Extruded Round Tubes for General-Purpose Applications |
| ASTM B 230/B230M : 2007 : R2012 | Standard Specification for Aluminum 1350–H19 Wire for Electrical Purposes |
| ASTM B 807/B807M : 2013 : REDLINE | Standard Practice for Extrusion Press Solution Heat Treatment for Aluminum Alloys |
| ASTM B 107/B107M : 2013 : REDLINE | Standard Specification for Magnesium-Alloy Extruded Bars, Rods, Profiles, Tubes, and Wire |
| ASTM B 316/B316M : 2015 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods |
| ISO 6363-2:2012 | Wrought aluminium and aluminium alloys — Cold-drawn rods/bars and tubes and wires — Part 2: Mechanical properties |
| SAE AMS4286F | Aluminum Alloy Castings, Permanent Mold 7.0Si - 0.32Mg (356.0-T51) As-Cast then Precipitation Heat Treated |
| ASTM B 917/B917M : 2012 : REDLINE | Standard Practice for Heat Treatment of Aluminum-Alloy Castings from All Processes |
| SAE AMS4335A | Forgings, Aluminum Alloys 2xxx and 7xxx, Heat-Treated, Finished-Part Properties: Short-Transverse Tensile Properties and Fracture Toughness |
| SAE J454_201801 | General Data on Wrought Aluminum Alloys |
| SAE AMS4420P | Magnesium Alloy Castings, Sand 6Al - 3Zn (AZ63A-F) As Cast |
| ASTM B 241/B241M : 2016 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube |
| ISO 6361-1:2011 | Wrought aluminium and aluminium alloys — Sheets, strips and plates — Part 1: Technical conditions for inspection and delivery |
| SAE AMS4429A | Magnesium Alloy Castings, Sand 2.8Nd - 1.4Gd - 0.4Zn - 0.6Zr (EV31A - T6) Solution and Precipitation Heat Treated |
| ASTM B 230/B230M : 2007 : R2016 | Standard Specification for Aluminum 1350–H19 Wire for Electrical Purposes |
| SAE AMS4437F | Magnesium Alloy Castings, Sand 8.7Al - 0.70Zn (AZ91C-T6) Solution Heat Treated and Aged |
| ASTM B 947 : 2014 : REDLINE | Standard Practice for Hot Rolling Mill Solution Heat Treatment for Aluminum Alloy Plate |
| ASTM B 211M : 2012 : EDT 1 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold-Finished Bar, Rod, and Wire (Metric) (Withdrawn 2019) |
| ASTM B 209M : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric) |
| MIL-STD-3049 Base Document:2013 | Materials Deposition, DDM: Direct Deposition of Metal for Remanufacture, Restoration and Recoating |
| ASTM B 483/B483M : 2013 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Pipe for General Purpose Applications |
| ASTM C 1671 : 2015 : REDLINE | Standard Practice for Qualification and Acceptance of Boron Based Metallic Neutron Absorbers for Nuclear Criticality Control for Dry Cask Storage Systems and Transportation Packaging |
| SAE AMS4249A | Aluminum Alloy Castings 7.0Si - 0.58Mg - 0.15Ti - 0.06Be (D357.0-T6) Solution and Precipitation Heat Treated (Requiring Fatigue and Fracture Toughness Testing) |
| SAE AMS4418H | Magnesium Alloy, Sand Castings 2.5Ag - 2.1Di - 0.70Zr (QE22A-T6) Solution and Precipitation Heat Treated |
| ASTM B 234M : 2017 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers (Metric) |
| SAE AMS2772G | Heat Treatment of Aluminum Alloy Raw Materials |
| SAE AMS4214J | Castings, Aluminum Alloy Sand 5.0Si - 1.2Cu - 0.50Mg (355.0-T71) Solution Heat Treated and Overaged |
| BS ISO 6362-2:2014 | Wrought aluminium and aluminium alloys. Extruded rods/bars, tubes and profiles Mechanical properties |
| SAE AMS4285F | Aluminum Alloy Castings, Centrifugal 7.0Si - 0.30Mg (356.0-T6) Solution and Precipitation Heat Treated |
| ASTM E 8M : 2004 | Standard Test Methods for Tension Testing of Metallic Materials [Metric] (Withdrawn 2008) |
| SAE AMS4406A | Aluminum Alloy, Centrifugal Castings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (709.0-T61) Hot Isostatically Pressed, Solution and Precipitation Heat Treated |
| ASTM B 90/B90M : 2015 : REDLINE | Standard Specification for Magnesium-Alloy Sheet and Plate |
| SAE AMS4482 | Cast Aluminum Alloy Composite 4.6 Cu – 3.4Ti – 1.4B – 0.75Ag – 0.27Mg (A205.0/TiB2/3p-T7P) Sand Cast, Solution and Precipitation Heat Treated |
| SAE AMS4225E | Aluminum Alloy, Heat-Resistant, Castings 5.0Cu - 1.5Ni - 0.25Mn - 0.25Sb - 0.25Co - 0.20Ti - 0.20Zr (203.0-T6) Solution Heat Treated and Precipitation Heat Treated |
| SAE AMS4212L | Aluminum Alloy Castings 5.0Si - 1.2Cu - 0.50Mg (355.0-T6) Solution and Precipitation Heat Treated |
| SAE AMS4417C | Castings, Sand, Magnesium Alloy 1.5Ag - 2.1Di - 0.08Cu - 0.70Zr (EQ21A - T6) Solution and Precipitation Heat Treated |
| SAE AMS4371B | Magnesium Alloy, Plate 4.0Y - 2.25Nd - 0.5Zr (WE43C - T5) Precipitation Heat Treated |
| SAE AMS3025E | Polyalkylene Glycol Heat Treat Quenchant |
| ASTM B 90M : 1990 | Specification for Magnesium-Alloy Sheet and Plate (Metric) (Withdrawn 1993) |
| ASTM B 483/B483M : 2013 : EDT 1 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Drawn Pipe for General Purpose Applications |
| ASTM B 236M : 2007 : R2015 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) (Metric) (Withdrawn 2024) |
| ASTM B 398M : 1997 | Standard Specification for Aluminum-Alloy 6201-T81 Wire for Electrical Purposes [Metric] (Withdrawn 1999) |
| ASTM B 404/B404M : 2002 | Standard Specification for Aluminum and Aluminum-Alloy Seamless Condenser and Heat-Exchanger Tubes with Integral Fins (Withdrawn 2006) |
| SAE AMS4219F | Aluminum Alloy Castings 7.0Si - 0.55Mg - 0.12Ti - 0.06Be (A357.0 T6) Solution and Precipitation Heat Treated |
| ASTM B 236M : 2007 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) [Metric] |
| DIN 29546:1990-10 | Aerospace; wrought aluminium alloys sheet, plate and strip; technical specification; inactive for new design |
| 09/30196316 DC : 0 | BS ISO 6361-1 - WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS - SHEETS, STRIPS AND PLATES - PART 1: TECHNICAL CONDITIONS FOR INSPECTION AND DELIVERY |
| ASTM B 646 : 2017 : REDLINE | Standard Practice for Fracture Toughness Testing of Aluminum Alloys |
| SAE AMS4261G | Aluminum Alloy Castings, Investment 7.0Si - 0.32Mg (356.0-T51) Precipitation Heat Treated |
| SAE AMS4229G | Aluminum Alloy Castings, High Strength 4.5Cu - 0.70Ag - 0.30Mn - 0.25Mg - 0.25Ti (A201.0-T7) Solution Heat Treated and Overaged |
| SAE AMS4452E | Magnesium Alloy, Investment Castings 8.7Al - 0.70Zn - 0.22Mn (AZ91C-T6) Solution and Precipitation Heat Treated |
| SAE AMS4215H | Aluminum Alloy, Castings 5.0Si - 1.2Cu - 0.50Mg (C355.0-T6) Solution and Precipitation Heat Treated |
| SAE AMS4453F | Magnesium Alloy, Investment Castings 9.0Al - 2.0Zn (AZ92A-T6) Solution and Precipitation Heat Treated |
| SAE AMS4434N | Magnesium Alloy Castings, Sand 9.0Al - 2.0Zn (AZ92A-T6) Solution and Precipitation Heat Treated |
| SAE AMS4281G | Aluminum Alloy Castings, Permanent Mold 5.0Si - 1.2Cu - 0.50Mg (355.0-T6) Solution and Precipitation Heat Treated |
| ASTM B 230/B230M : 2007 | Standard Specification for Aluminum 1350-H19 Wire for Electrical Purposes |
| SAE AMS4455G | Magnesium Alloy, Investment Castings 10Al (AM100A-T6) Solution and Precipitation Heat Treated |
| ASTM F 3160 : 2016 | Standard Guide for Metallurgical Characterization of Absorbable Metallic Materials for Medical Implants |
| ASTM B 313M : 1988 | Specification for Aluminum and Aluminum-Alloy Round Welded Tubes (Metric) (Withdrawn 1990) |
| ISO 6362-1:2012 | Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 1: Technical conditions for inspection and delivery |
| SAE AMS4280J | Aluminum Alloy Castings, Permanent Mold 5.0Si - 1.2Cu - 0.5Mg (355.0-T71) Solution Heat Treated and Overaged |
| SAE MAM4427A | Magnesium Alloy Sand Castings 4.0y 2.3nd 0.7zr Solution and Precipitation Heat Treated |
| SAE AMS4258B | Laminated Sheet, Aluminum Alloy, Aramid Fiber Reinforced 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (Alclad, One Side 7475-T761) 5 or 7 Ply |
| ASTM B 928 : 2004 | Standard Specification for High Magnesium Aluminum-Alloy Sheet and Plate for Marine Service |
| SAE AMS4444E | Magnesium Alloy Castings, Sand 6.0Zn - 0.80Zr (ZK61A-T5) Precipitation Heat Treated |
| SAE AMS4471A | Cast Aluminum Alloy Composite 4.6Cu - 3.4Ti - 1.4B - 0.75Ag - 0.27Mg (205.0/TiB2/3p-T7P) Investment Cast, Solution and Precipitation Heat Treated |
| DIN 65166:1986-09 | AEROSPACE; WROUGHT ALUMINIUM ALLOY WEDGE; TECHNICAL SPECIFICATIONS |
| ASTM E 8/E8M : 2016-09 | TEST METHODS FOR TENSION TESTING OF METALLIC MATERIALS |
| SAE AMS4217J | Aluminum Alloy, Castings 7.0Si - 0.32Mg (356.0-T6) Solution and Precipitation Heat Treated |
| SAE AMS4425D | Magnesium Alloy Castings, Sand 5.8Zn - 2.5RE - 0.70Zr (ZE63-T6) Solution and Precipitation Heat Treated |
| SAE AMS4107G | Aluminum Alloy Die Forgings (7050-T74) Solution Heat Treated and Overaged |
| SAE AMS4288 | Aluminum Alloy Castings 7.0Si - 0.58Mg - 0.15Ti (E357.0-T6) Solution and Precipitation Heat Treated |
| ISO 6363-1:2012 | Wrought aluminium and aluminium alloys — Cold-drawn rods/bars, tubes and wires — Part 1: Technical conditions for inspection and delivery |
| SAE AMS4242C | Aluminum Alloy, Castings 4.7Cu - 0.60Ag - 0.35Mn - 0.25Mg - 0.25Ti (B201.0-T7) Solution Heat Treated and Overaged |
| SAE AMS4443H | Magnesium Alloy, Sand Castings 4.5Zn - 0.75Zr (ZK51A-T5) Precipitation Heat Treated |
| ISO 6362-2:2014 | Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 2: Mechanical properties |
| ASTM B 308M : 1988 | Specification for Aluminum-Alloy 6061-T6 Standard Structural Shapes, Rolled or Extruded (Metric) (Withdrawn 1990) |
| ASTM B 211M : 2012 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold-Finished Bar, Rod, and Wire (Metric) |
| ASTM B 609M : 1997 | Standard Specification for Aluminum 1350 Round Wire, Annealed and Intermediate Tempers, for Electrical Purposes [Metric] (Withdrawn 1999) |
| ASTM B 247M : 2020 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings (Metric) |
| ASTM E 345 : 2016 : REDLINE | Standard Test Methods of Tension Testing of Metallic Foil |
| ASTM E 83 : 2016 : REDLINE | Standard Practice for Verification and Classification of Extensometer Systems |
| ASTM E 8M : 2004 | Standard Test Methods for Tension Testing of Metallic Materials [Metric] (Withdrawn 2008) |
| ASTM B 209 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate |
Summarise
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.