ASTM D 1149 : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment
Hardcopy , PDF
20-09-2018
English
01-01-2016
Committee |
D 11
|
DocumentType |
Test Method
|
Pages |
13
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1These test methods are used to estimate the effect of exposure, under surface tensile strain conditions, either dynamic or static, in an atmosphere containing specified levels of ozone concentration, expressed as partial pressure (refer to Note 1), on vulcanized rubber, rubber compounds, molded or extruded soft rubber, and other specified materials, or as may be determined empirically. The effect of naturally occurring sunlight or light from artificial sources is excluded.
1.2Previously published ASTM documents Test Method D518 and Test Methods D3395 have been included in these test methods, D1149, in 2007. Please refer to Note 2.
1.2.1Test Method D518 and Test Methods D3395 have henceforth been withdrawn and superseded by Test Methods D1149. When Test Methods D1149 is cited, or otherwise referenced, a notation shall be included to this effect. Please refer to section 3.2 for the appropriate references.
1.3The specified conditions of exposure to ozone in the controlled environments are accelerated in comparison to outdoor exposure. These accelerated ozone test methods may not give results which correlate with outdoor exposure tests or service performance.
1.4All materials, instruments, or equipment used for the determination of mass, force, dimension, ozone concentration, partial pressure, temperature, velocity, and gas exchange rate shall have direct traceability to the National Institute for Standards and Technology, or other internationally recognized organization parallel in nature.
1.5The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. Many of the stated SI units are direct conversions from the U.S. Customary System to accommodate the instrumentation, practices, and procedures that existed prior to the Metric Conversion Act of 1975.
1.6This standard involves hazardous materials, specifically ozone. It may also involve hazardous operations and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1:A discussion and explanation regarding the measurement of ozone concentrations based upon parts of ozone per unit of air versus partial pressure is provided in Test Methods D4575, specifically Appendices X1 and X2. Test Methods D4575 is also recommended as a source of background information regarding standards involving materials exposed to ozone.
ASTM C 509 : 2006 : R2015 | Standard Specification for Elastomeric Cellular Preformed Gasket and Sealing<brk/> Material |
ASTM C 542 : 2005 : R2017 | Standard Specification for Lock-Strip Gaskets |
ASTM D 380 : 1994 : R2012 | Standard Test Methods for Rubber Hose |
ASTM E 1783/E1783M : 1996 : R2017 | Standard Specification for Preformed Architectural Strip Seals for Buildings and Parking Structures |
ASTM D 5973 : 1997 : R2017 | Standard Specification for Elastomeric Strip Seals with Steel Locking Edge Rails Used in Expansion Joint Sealing |
ASTM D 2628 : 1991 : R2016 | Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Concrete Pavements |
ASTM D 6924 : 2003 : R2017 | Standard Specification for Preformed Thermoplastic Vulcanizate Elastomeric Joint Seals for Bridges |
ASTM F 724 : 1994 : REV A : R2016 | Standard Test Method for Outdoor Evaluation of Tire Sidewall Component Cracking Resistance |
ASTM D 3468/D3468M : 1999 : R2013 : EDT 1 | Standard Specification for Liquid-Applied Neoprene and Chlorosulfonated Polyethylene Used in Roofing and Waterproofing |
ASTM C 864 : 2005 : R2019 | Standard Specification for Dense Elastomeric Compression Seal Gaskets, Setting Blocks, and Spacers |
ASTM D 378 : 2010 : R2016 | Standard Test Methods for Rubber (Elastomeric) Conveyor Belting, Flat Type |
ASTM D 3542 : 2008 : R2013 | Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Bridges |
ASTM D 429 : 2014 | Standard Test Methods for Rubber Property—Adhesion to Rigid Substrates |
ASTM F 2320 : 2018 | Standard Specification for Rubber Insulating Sheeting |
ASTM E 2203 : 2014 : R2018 | Standard Specification for Dense Thermoplastic Elastomers Used for Compression Seals, Gaskets, Setting Blocks, Spacers and Accessories |
ASTM E 1612/E1612M : 1994 : R2017 | Standard Specification for Preformed Architectural Compression Seals for Buildings and Parking Structures |
ASTM D 3667 : 2016 | Standard Specification for Rubber Seals Used in Flat-Plate Solar Collectors |
ASTM D 3832 : 1979 : R2017 | Standard Specification for Rubber Seals Contacting Liquids in Solar Energy Systems |
ASTM D 3105 : 2017 | Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials |
ASTM D 4014 : 2003 : R2018 | Standard Specification for Plain and Steel-Laminated Elastomeric Bearings for Bridges |
ASTM C 1644 : 2006 : R2017 | Standard Specification for Resilient Connectors Between Reinforced Concrete On-Site Wastewater Tanks and Pipes |
ASTM D 622 : 1999 : R2012 | Standard Test Methods for Rubber Hose for Automotive Air and Vacuum Brake System |
ASTM D 4000 : 2016 | Standard Classification System for Specifying Plastic Materials |
ASTM D 2000 : 2018 | Standard Classification System for Rubber Products in Automotive Applications |
ASTM C 1277 : 2018 | Standard Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings |
ASTM D 7106/D7106M : 2005 : R2015 : EDT 1 | Standard Guide for Selection of Test Methods for Ethylene Propylene Diene Terpolymer (EPDM) Geomembranes |
ASTM C 1478M : 2019 | Standard Specification for Storm Drain Resilient Connectors Between Reinforced Concrete Storm Sewer Structures, Pipes, and Laterals (Metric) (Withdrawn 2020) |
ASTM D 7465/D7465M : 2015 : R2019 | Standard Specification for Ethylene Propylene Diene Terpolymer (EPDM) Sheet Used In Geomembrane Applications |
ASTM D 5926 : 2015 | Standard Specification for Poly (Vinyl Chloride) (PVC) Gaskets for Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems |
ASTM C 1173 : 2018 | Standard Specification for Flexible Transition Couplings for Underground Piping Systems |
ASTM C 1208/C1208M : 2018 | Standard Specification for Vitrified Clay Pipe and Joints for Use in Microtunneling, Sliplining, Pipe Bursting, and Tunnels |
ASTM D 4637/D4637M : 2015 | Standard Specification for EPDM Sheet Used In Single-Ply Roof Membrane |
ASTM C 505M : 2019 | Standard Specification for Nonreinforced Concrete Irrigation Pipe With Rubber Gasket Joints (Metric) |
ASTM C 505 : 2019 | Standard Specification for Nonreinforced Concrete Irrigation Pipe with Rubber Gasket Joints |
ASTM D 3903 : 2015 | Standard Specification for Rubber Seals Used in Air-Heat Transport of Solar Energy Systems |
ASTM D 4575 : 2009 : R2015 | Standard Test Methods for Rubber Deterioration—Reference and Alternative Method(s) for Determining Ozone Level in Laboratory Test Chambers |
ASTM F 3240 : 2017 | Standard Practice for Installation of Seamless Molded Hydrophilic Gaskets (SMHG) for Long-Term Watertightness of Cured-in-Place Rehabilitation of Main and Lateral Pipelines |
ASTM D 6878/D6878M : 2017 | Standard Specification for Thermoplastic Polyolefin Based Sheet Roofing |
ASTM C 564 : 2014 | Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings |
ASTM F 477 : 2014 | Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe |
ASTM C 1115 : 2017 | Standard Specification for Dense Elastomeric Silicone Rubber Gaskets and Accessories |
ASTM F 913 : 2002 : R2014 | Standard Specification for Thermoplastic Elastomeric Seals (Gaskets) for Joining<brk/> Plastic Pipe |
ASTM D 3771 : 2015 | Standard Specification for Rubber Seals Used in Concentrating Solar Collectors |
ASTM C 1619 : 2019 | Standard Specification for Elastomeric Seals for Joining Concrete Structures |
ASTM D 1171 : 2018 | Standard Test Method for Rubber Deterioration—Surface Ozone Cracking Outdoors (Triangular Specimens) |
ASTM D 4811/D4811M : 2016 | Standard Specification for Nonvulcanized (Uncured) Rubber Sheet Used as Roof Flashing |
ASTM C 1478 : 2019 | Standard Specification for Storm Drain Resilient Connectors Between Reinforced Concrete Storm Sewer Structures, Pipes, and Laterals |
ANSI/AWWA C219:2023 | Bolted Sleeve-Type Couplings for Plain-End Pipe |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.