• Shopping Cart
    There are no items in your cart

ASTM D 1310 : 2001 : R2007

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus

Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Superseded by

ASTM D 1310 : 2014

Language(s)

English

Published date

01-06-2007

€67.30
Excluding VAT

Committee
D 01
DocumentType
Test Method
Pages
8
ProductNote
Reconfirmed 2007
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1 This test method covers the determination by Tag Open-Cup Apparatus of the flash point and fire point of liquids having flash points between 18 and 165°C (0 and 325°F) and fire points up to 325°F.

1.2 This test method, when applied to paints and resin solutions that tend to skin over or that are very viscous, gives less reproducible results than when applied to solvents. Note 1 - In order to conserve time and sample, the fire point of a material may be determined by the Tag Open-Cup Method by continuing the heating of the specimen to its fire point. Fire points may also be determined by Test Method D 92, which should be used for fire points beyond the scope of this test method.

1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.4 This standard should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors pertinent to an assessment of the fire hazard of a particular end use

This standard does not purport to address the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM D 92 : 2018 Standard Test Method for Flash and Fire Points by Cleveland Open Cup Tester
ASTM D 3143/D3143M : 2019 Standard Test Method for Flash Point of Cutback Asphalt with Tag Open-Cup Apparatus
ASTM D 56 : 2016 : REV A Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM D 5958 : 1999 : R2012 : EDT 1 Standard Practices for Preparation of Oil-Based Ink Resin Solutions
ASTM C 647 : 2019 Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation
ASTM D 4800 : 1994 : R2015 Standard Guide for Classifying and Specifying Adhesives
ASTM F 3337 : 2019 Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil
ASTM D 6465 : 1999 : R2016 Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants
ASTM D 3105 : 2017 Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials
ASTM D 6038 : 2014 Standard Test Methods for Determining the Compatibility of Resin/Solvent Mixtures by Precipitation Temperature (Cloud Point)
ASTM D 268 : 2001 : R2012 Standard Guide for Sampling and Testing Volatile Solvents and Chemical Intermediates for Use in Paint and Related Coatings and Material (Withdrawn 2021)
ASTM E 502 : 2007 : R2013 Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.