ASTM D 1400 : 2000
Withdrawn
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
View Superseded by
Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Nonconductive Coatings Applied to a Nonferrous Metal Base (Withdrawn 2006)
Available format(s)
Hardcopy , PDF
Withdrawn date
19-06-2006
Superseded by
Language(s)
English
Published date
31-12-2010
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 06.01, 2008 Outlines the non-destructive measurement of the dry film thickness of electrically non-conductive coatings used over a non-ferrous metal base using eddy current instruments.
| Committee |
D 01
|
| DocumentType |
Test Method
|
| Pages |
2
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Withdrawn
|
| SupersededBy | |
| Supersedes |
1.1 This test method covers the nondestructive measurement of the dry film thickness of electrically nonconductive coatings applied over a nonferrous metal base using commercially available eddy current instruments. This test method is intended to supplement manufacturers' instructions for the manual operation of the gages, and is not intended to replace them.
1.2 This test method is not applicable to coatings that will be readily deformable under the load of the measuring instruments, as the instrument probe must be placed directly on the coating surface to take a reading.
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 5087 : 2002 : R2014 | Standard Test Method for Determining Amount of Volatile Organic Compound (VOC) Released from Solventborne Automotive Coatings and Available for Removal in a VOC Control Device (Abatement) |
| CNG FUEL INSPECTOR RESOURCE PACKAGE : 2013 | CONSISTS OF ANSI NGV 1-2006/CSA NGV 1-2006, COMPRESSED NATURAL GAS VEHICLE (NGV) FUELING CONNECTION DEVICES; ANSI PRD 1-2013, PRESSURE RELIEF DEVICES FOR NATURAL GAS VEHICLE (NGV) FUEL CONTAINERS; ANSI NGV 2-2007, COMPRESSED NATURAL GAS VEHICLE FUEL CONTAINERS; ANSI NGV 2A-2012, ADDENDA 1 TO ANSI NGV 2-2007, COMPRESSED NATURAL GAS VEHICLE FUEL CONTAINERS AND ANSI NGV 2B-2012 |
| ASTM D 658 : 1991 | Standard Test Method for Abrasion Resistance of Organic Coatings by Air Blast Abrasive (Withdrawn 1996) |
| ASTM E 842 : 1982 | Specification for Lawn Buildings (Withdrawn 1990) |
| ASTM D 3730 : 2017 : REDLINE | Standard Guide for Testing High-Performance Interior Architectural Wall Coatings |
| ASTM D 2134 : 1993 : R2001 | Test Method for Determining the Hardness of Organic Coatings with a Sward-Type Hardness Rocker |
| ASTM D 4712 : 1987 : REV A : R1996 | Standard Guide for Testing Industrial Water-Reducible Coatings |
| NACE RP 02 81 : 2004 | METHOD FOR CONDUCTING COATING (PAINT) PANEL EVALUATION TESTING IN ATMOSPHERIC EXPOSURES |
| MIL M 17508 : F | MOUNTS, RESILIENT: TYPES 6E100, 6E150, 7E450, 6E900, 6E2000, 5E3500, 6E100BB, 6E150BB, 7E450BB, AND 6E900BB |
| MIL L 46010 : D | LUBRICANT, SOLID FILM, HEAT CURED, CORROSION INHIBITING |
| MIL M 19863 : D | MOUNT, RESILIENT, TYPE 5B5.000H |
| MIL V 24509 : A | VALVES, FLANGED, BALL & PLUG FOR SEWAGE & SEA WATER SERVICE |
| MIL L 46147 : B | LUBRICANT, SOLID FILM, AIR CURED (CORROSION INHIBITING) |
| MIL L 0046010 : D | LUBRICANT, SOLID FILM, HEAT CURED, CORROSION INHIBITING |
| MIL-W-50849 Revision D:1986 | WARHEAD GUIDED MISSILE HE M250 INERT PARTS FOR |
| ASTM D 5087 : 2002 : R2008 | Standard Test Method for Determining Amount of Volatile Organic Compound (VOC) Released from Solventborne Automotive Coatings and Available for Removal in a VOC Control Device (Abatement) |
| SAE AS5272E | Lubricant, Solid Film, Heat Cured, Corrosion Inhibiting, Procurement Specification |
| ASTM D 1474 : 1998 | Standard Test Methods for Indentation Hardness of Organic Coatings |
| ASTM F 1178 : 2011 | Standard Specification for Performance of Enameling System, Baking, Metal Joiner Work and Furniture |
| ASTM D 2134 : 1993 | Test Method for Determining the Hardness of Organic Coatings with a Sward-Type Hardness Rocker |
| ASTM D 2134 : 1993 : R2007 | Standard Test Method for Determining the Hardness of Organic Coatings with a Sward-Type Hardness Rocker |
| ASTM D 6762 : 2002 | Standard Test Method for Determining the Hiding Power of Paint by Visual Evaluation of Spray Applied Coatings |
| ASTM D 6905 : 2003 : R2008 | Standard Test Method for Impact Flexibility of Organic Coatings |
| ASTM D 6762 : 2002 : EDT 1 | Standard Test Method for Determining the Hiding Power of Paint by Visual Evaluation of Spray Applied Coatings |
| ASTM D 4587 : 2011 : REDLINE | Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings |
| ASTM D 5286 : 2001 : R2017 | Standard Test Methods for Determination of Transfer Efficiency Under General Production Conditions for Spray Application of Paints |
| ASTM D 6905 : 2003 | Standard Test Method for Impact Flexibility of Organic Coatings |
| ASTM D 6486 : 2001 : R2017 | Standard Practice for Short Term Vehicle Service Exposure of Automotive Coatings |
| ASTM D 5286 : 2001 : R2011 | Standard Test Methods for Determination of Transfer Efficiency Under General Production Conditions for Spray Application of Paints |
| ASTM D 3322 : 1982 : R2001 | Standard Practice for Testing Primers and Primer Surfacers Over Preformed Metal |
| ASTM D 5286 : 2001 : R2005 | Standard Test Methods for Determination of Transfer Efficiency Under General Production Conditions for Spray Application of Paints |
| ASTM D 2248 : 2001 : REV A : R2018 | Standard Practice for Detergent Resistance of Organic Finishes |
| ASTM D 522 : 1993 : REV A | Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings |
| ASTM D 2248 : 2001 | Standard Practice for Detergent Resistance of Organic Finishes |
| ASTM D 6762 : 2002 : REV A : R2017 | Standard Test Method for Determining the Hiding Power of Paint by Visual Evaluation of Spray Applied Coatings |
| ASTM D 3322 : 1982 : R2005 | Standard Practice for Testing Primers and Primer Surfacers Over Preformed Metal |
| ASTM D 2248 : 2001 : REV A : R2013 | Standard Practice for Detergent Resistance of Organic Finishes |
| ASTM D 3322 : 1982 : R2011 | Standard Practice for Testing Primers and Primer Surfacers Over Preformed Metal |
| ASTM D 6486 : 2001 : R2005 | Standard Practice for Short Term Vehicle Service Exposure of Automotive Coatings |
| ASTM D 5286 : 2001 | Standard Test Methods for Determination of Transfer Efficiency Under General Production Conditions for Spray Application of Paints |
| ASTM D 3322 : 1982 : R2017 | Standard Practice for Testing Primers and Primer Surfacers Over Preformed Metal |
| ASTM D 3322 : 1982 : R1996 : EDT 1 | Standard Practice for Testing Primers and Primer Surfacers Over Preformed Metal |
| ASTM D 2248 : 2001 : REV A : R2007 | Standard Practice for Detergent Resistance of Organic Finishes |
| ASTM D 6486 : 2001 | Standard Practice for Short Term Vehicle Service Exposure of Automotive Coatings |
| ASTM D 2248 : 2001 : REV A | Standard Practice for Detergent Resistance of Organic Finishes |
| ASTM D 522 : 1993 : REV A : R2001 | Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings |
| ASTM D 6905 : 2003 : R2012 | Standard Test Method for Impact Flexibility of Organic Coatings |
| ASTM D 6762 : 2002 : REV A : R2009 : EDT 1 | Standard Test Method for Determining the Hiding Power of Paint by Visual Evaluation of Spray Applied Coatings |
| ASTM D 6486 : 2001 : R2011 | Standard Practice for Short Term Vehicle Service Exposure of Automotive Coatings |
| ASTM D 6762 : 2002 : REV A | Standard Test Method for Determining the Hiding Power of Paint by Visual Evaluation of Spray Applied Coatings |
| ASTM D 6279 : 2015 : REDLINE | Standard Test Method for Rub Abrasion Mar Resistance of High Gloss Coatings |
| ASTM D 522 : 1993 : REV A : R2008 | Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings |
| BS EN 16602-70-31:2014 | Space product assurance. Application of paints and coatings on space hardware |
| ASTM D 5178 : 2016 : REDLINE | Standard Test Method for Mar Resistance of Organic Coatings |
| ASTM D 6695 : 2016 : REDLINE | Standard Practice for Xenon-Arc Exposures of Paint and Related Coatings |
| ASTM D 2091 : 1996 : R2003 | Standard Test Method for Print Resistance of Lacquers |
| ASTM D 2091 : 1996 : R2017 | Standard Test Method for Print Resistance of Lacquers |
| ASTM D 2336 : 1999 | Standard Guide for Specifying Factory Applied Wood Coatings (Withdrawn 2008) |
| ASTM D 5161 : 2004 : REV A | Standard Guide for Specifying Inspection Requirements for Coating and Lining Work (Metal Substrates) (Withdrawn 2013) |
| CSA B51S1 : 2005 | SUPPLEMENT NO. 1 TO B51-03, BOILER, PRESSURE VESSEL, AND PRESSURE PIPING CODE |
| ASTM D 3170/D3170M : 2014 : REDLINE | Standard Test Method for Chipping Resistance of Coatings |
| ASTM D 5161 : 2004 | Standard Guide for Specifying Inspection Requirements for Coating and Lining Work (Metal Substrates) |
| ASTM D 5087 : 2002 | Standard Test Method for Determining Amount of Volatile Organic Compound (VOC) Released from Solventborne Automotive Coatings and Available for Removal in a VOC Control Device (Abatement) |
| ASTM D 333 : 2001 : R2007 | Standard Guide for Clear and Pigmented Lacquers |
| CSA B51 : 2014 | BOILER, PRESSURE VESSEL, AND PRESSURE PIPING CODE |
| ASTM D 1474 : 1998 : R2002 | Standard Test Methods for Indentation Hardness of Organic Coatings |
| ASTM D 4712 : 1987 : REV A : R2001 | Standard Guide for Testing Industrial Water-Reducible Coatings |
| ASTM D 4712 : 1987 : REV A : R2005 | Standard Guide for Testing Industrial Water-Reducible Coatings (Withdrawn 2014) |
| ASTM D 2091 : 1996 : R2011 | Standard Test Method for Print Resistance of Lacquers |
| EN 16602-70-31:2014 | Space product assurance - Application of paints and coatings on space hardware |
| ASTM D 333 : 2001 : R2013 | Standard Guide for Clear and Pigmented Lacquers |
| ASTM D 333 : 2001 | Standard Guide for Clear and Pigmented Lacquers |
| ASTM F 1178 : 2011 : R2015 | Standard Specification for Performance of Enameling System, Baking, Metal Joiner Work and Furniture |
| ASTM E 843 : 1982 | Specification for Covers, Carports, and Canopies (Withdrawn 1990) |
| ASTM D 1474 : 1998 : R2008 | Standard Test Methods for Indentation Hardness of Organic Coatings |
| ASTM D 2134 : 1993 : R2012 | Standard Test Method for Determining the Hardness of Organic Coatings with a Sward-Type Hardness Rocker |
| ASTM D 2091 : 1996 | Standard Test Method for Print Resistance of Lacquers |
| CSA/ANSI NGV2 : 2016 | COMPRESSED NATURAL GAS VEHICLE FUEL CONTAINERS |
| ASTM D 823 : 1995 | Standard Practices for Producing Films of Uniform Thickness of Paint, Varnish, and Related Products on Test Panels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.