• There are no items in your cart

ASTM D 1693 : 2015 : EDT 1

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics

Available format(s)

Hardcopy , PDF

Superseded date

05-11-2021

Superseded by

ASTM D 1693 : 2021

Language(s)

English

Published date

21-08-2020

€74.48
Excluding VAT

Committee
D 20
DocumentType
Test Method
Pages
11
ProductNote
ε1NOTE—Adjunct footnote was editorially corrected in August 2020.
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This test method covers the determination of the susceptibility of ethylene plastics, as defined in Terminology D883, to environmental stress-cracking when subjected to the conditions herein specified. Under certain conditions of stress and in the presence of environments such as soaps, wetting agents, oils, or detergents, ethylene plastics may exhibit mechanical failure by cracking.

1.2The values stated in SI units are to be regarded as standard.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Note 1:There is no known ISO equivalent to this standard.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D 3554 : 2020 : EDT 1 Standard Specification for Track-Resistant Thermoplastic High-Density Polyethylene Insulation for Wire and Cable, 75 °C Operation
ASTM D 2308 : 2007 : R2020 : EDT 1 Standard Specification for Thermoplastic Polyethylene Jacket for Electrical Wire and Cable
ASTM D 4976 : 2012 : REV A : R2020 Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
ASTM F 810 : 2012 : R2018 Standard Specification for Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields
ASTM D 1998 : 2021 Standard Specification for Polyethylene Upright Storage Tanks
ASTM F 2718 : 2009 : R2015 Standard Specification for Polyethylene (PE) and Cement Materials for an Encapsulated Cement Mortar Formed in Place Liner System (FIPLS) for the Rehabilitation of Water Pipelines (Withdrawn 2022)
ASTM D 7082 : 2021 Standard Specification for Polyethylene Stay In Place Form System for End Walls for Drainage Pipe
ASTM D 7436 : 2017 Standard Classification System for Unfilled Polyethylene Plastics Molding and Extrusion Materials with a Fractional Melt Index Using ISO Protocol and Methodology
ASTM F 2160 : 2016 Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD)
ASTM D 4565 : 2020 Standard Test Methods for Physical and Environmental Performance Properties of <brk/>Insulations and Jackets for Telecommunications Wire and Cable
ASTM D 1248 : 2016 Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable
ASTM F 2896 : 2011 : R2017 Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids
ASTM D 543 : 2020 Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
ASTM D 8269 : 2021 Standard Guide for the Use of Geocells in Geotechnical and Roadway Projects
ASTM D 3350 : 2021 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM F 1533 : 2020 Standard Specification for Deformed Polyethylene (PE) Liner
ASTM D 4000 : 2020 Standard Classification System for Specifying Plastic Materials
ASTM D 3485 : 2015 Standard Specification for Coilable High Density Polyethylene (HDPE) Cable in Conduit (CIC)

ASTM D 3350 : 2021 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM E 691 : 2020 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 3350 : 2014 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM E 691 : 2019 : EDT 1 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 691 : 2009 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 618 : 2013 Standard Practice for Conditioning Plastics for Testing
ASTM D 618 : 2021 Standard Practice for Conditioning Plastics for Testing

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.