ASTM D 1710 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Extruded Polytetrafluoroethylene (PTFE) Rod, Heavy Walled Tubing and Basic Shapes
Hardcopy , PDF
05-11-2021
English
10-09-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
D 20
|
| DocumentType |
Standard
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers extruded polytetrafluoroethylene (PTFE) rod, heavy-walled tubing, and basic shapes manufactured from the PTFE resin of Specification D4894 and reprocessed PTFE resin (as defined in Guide D7209).
1.2The specification covers all sizes of rod, tubing, and basic shapes with a wall thickness of 1.6 mm (1/16in.) or greater. These materials must be made wholly from PTFE and produced in accordance with good commercial ram extrusion practices.
Note 1:This specification and ISO/DIS 13000-1 (1997) and ISO/DIS 13000-2 (1997) differ in approach, however, data obtained using either are technically equivalent.
Note 2:For compression molded PTFE materials, see Specification D3294. Material that can be certified to Specification D3294 may be substituted for Specification D1710, however the reverse in not true.
1.3The values stated in SI units, as detailed in IEEE/ASTM SI 10 are to be regarded as the standard. The inch-pound units given in parentheses are provided for information only.
1.4The following precautionary caveat pertains to the test methods portion, Section 12, only of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 3295 : 2015 | Standard Specification for PTFE Tubing, Miniature Beading and Spiral Cut Tubing |
| ASTM F 754 : 2008 : R2015 | Standard Specification for Implantable Polytetrafluoroethylene (PTFE) Sheet, Tube, and Rod Shapes Fabricated from Granular Molding Powders |
| ASTM D 3295 : 2020 | Standard Specification for PTFE Tubing, Miniature Beading and Spiral Cut Tubing |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 5947 : 1996 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 3892 : 2015 : R2020 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 4894 : 1998 : REV A | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ASTM D 5947 : 2002 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 5740 : 2003 | Standard Guide for Writing Material Standards in the Classification D4000 Format |
| ASTM D 4894 : 2007 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ASTM D 3892 : 1993 : R2003 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 3892 : 2015 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 7209 : 2006 | Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn 2015) |
| ASTM D 5947 : 2011 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 5947 : 2018 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 3892 : 1993 : R1998 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 5740 : 1997 | Standard Guide for Writing Material Standards in the Classification D4000 Format |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 5740 : 2016 | Standard Guide for Writing Material Standards in the Classification <astmref design="D4000"/> Format |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 5740 : 2011 | Standard Guide for Writing Material Standards in the Classification D4000 Format |
| ASTM D 5947 : 2006 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 4894 : 2004 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 5947 : 2003 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 5947 : 2001 : EDT 1 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 4894 : 2015 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ASTM D 4894 : 2019 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ASTM D 4894 : 2007 : R2012 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ASTM D 5740 : 2009 | Standard Guide for Writing Material Standards in the Classification D4000 Format |
| ASTM D 3892 : 1993 : R2009 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.