ASTM D 1754 : 1997
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Effect of Heat and Air on Asphaltic Materials (Thin-Film Oven Test)
Hardcopy , PDF
11-11-2014
English
10-08-1997
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1 Scope
2 Referenced Documents
3 Summary of Test Method
4 Significance and use
5 Apparatus
6 Preparation of samples
7 Procedure
8 Report
9 Precision and Bias
10 Keywords
CONTAINED IN VOL. 04.03, 2009 Determines effect of heat and air on film of semisolid asphaltic materials, using measurements of selected asphalt properties before and after test.
| Committee |
D 04
|
| DevelopmentNote |
Also numbered as AASHTO T 179. (08/2014)
|
| DocumentType |
Test Method
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1 This test method covers the determination of the effect of heat and air on a film of semisolid asphaltic materials. The effects of this treatment are determined from measurements of selected asphalt properties before and after the test.
1.2 The values stated in SI units are to be regarded as the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| 05/30138291 DC : DRAFT AUG 2005 | EN 12607-2 - BITUMEN AND BITUMINOUS BINDERS - DETERMINATION OF THE RESISTANCE TO HARDENING UNDER INFLUENCE OF HEAT AND AIR - PART 2: TFOT METHOD |
| ASTM D 946/D946M : 2015 : REDLINE | Standard Specification for Penetration-Graded Asphalt Binder for Use in Pavement Construction |
| ASTM D 6114/D6114M : 2009-07 | SPECIFICATION FOR ASPHALT-RUBBER BINDER |
| PREN 12607-2 : DRAFT 2013 | BITUMEN AND BITUMINOUS BINDERS - DETERMINATION OF THE RESISTANCE TO HARDENING UNDER THE INFLUENCE OF HEAT AND AIR - PART 2: TFOT METHOD |
| ASTM D 5892 : 2000 | Standard Specification for Type IV Polymer-Modified Asphalt Cement for Use in Pavement Construction (Withdrawn 2005) |
| ASTM D 6084/D6084M : 2013-12 | TEST METHOD FOR ELASTIC RECOVERY OF ASPHALT MATERIALS BY DUCTILOMETER |
| ASTM D 5840 : 2000 | Standard Specification for Type II Polymer Modified Asphalt Cement for Use in Pavement Construction (Withdrawn 2005) |
| ASTM D 3666 : 2016 : REDLINE | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 5841 : 2000 | Standard Specification for Type III Polymer Modified Asphalt Cement for Use in Pavement Construction (Withdrawn 2005) |
| ASTM D 4552 : 1992 : R2004 | Standard Practice for Classifying Hot-Mix Recycling Agents |
| ASTM D 6114 : 1997 : R2002 | Standard Specification for Asphalt-Rubber Binder |
| ASTM D 4552 : 1992 : R1999 | Standard Practice for Classifying Hot-Mix Recycling Agents |
| ASTM D 5801 : 2017 : REDLINE | Standard Test Method for Toughness and Tenacity of Asphalt Materials |
| BS 2000-460-2(2014) : 2014 | BITUMEN AND BITUMINOUS BINDERS - DETERMINATION OF THE RESISTANCE TO HARDENING UNDER INFLUENCE OF HEAT AND AIR - PART 2: TFOT METHOD |
| ASTM D 6626 : 2015 : REDLINE | Standard Specification for Performance Graded Trinidad Lake Modified Asphalt Binder |
| ASTM D 6114 : 1997 : EDT 1 | Standard Specification for Asphalt-Rubber Binder |
| ASTM D 5710 : 2005 | Standard Specification for Trinidad Lake Modified Asphalt |
| ASTM D 4552/D4552M : 2010 | Standard Practice for Classifying Hot-Mix Recycling Agents |
| I.S. EN 12607-2:2014 | BITUMEN AND BITUMINOUS BINDERS - DETERMINATION OF THE RESISTANCE TO HARDENING UNDER THE INFLUENCE OF HEAT AND AIR - PART 2: TFOT METHOD |
| BS 2000-460.2(2007) : 2007 | BITUMEN AND BITUMINOUS BINDERS - DETERMINATION OF THE RESISTANCE TO HARDENING UNDER THE INFLUENCE OF HEAT AND AIR - PART 2: TFOT METHOD |
| ACI 223 : 1998 | PRACTICE FOR THE USE OF SHRINKAGE-COMPENSATING CONCRETE |
| ASTM D 6154 : 2015 | Standard Specification for Chemically Modified Asphalt Cement for Use in Pavement Construction |
| ASTM D 946/D946M : 2015 | Standard Specification for Penetration-Graded Asphalt Binder for Use in Pavement Construction |
| ASTM D 5710/D5710M : 2015 | Standard Specification for Trinidad Lake Modified Asphalt |
| ASTM D 6626 : 2015 | Standard Specification for Performance Graded Trinidad Lake Modified Asphalt Binder |
| ASTM D 3666 : 2016 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 5505 : 2014 | Standard Practice for Classifying Emulsified Recycling Agents |
| ASTM D 5801 : 2017 | Standard Test Method for Toughness and Tenacity of Asphalt Materials |
| AASHTO T 51 : 2009 : R2013 | METHOD OF TEST FOR DUCTILITY OF ASPHALT MATERIALS |
| ASTM D 5976 : 2000 | Standard Specification for Type I Polymer Modified Asphalt Cement for Use in Pavement Construction (Withdrawn 2005) |
| ASTM D 6154 : 2015 : REDLINE | Standard Specification for Chemically Modified Asphalt Cement for Use in Pavement Construction |
| UNI EN 12607-2 : 2015 | BITUMEN AND BITUMINOUS BINDERS - DETERMINATION OF THE RESISTANCE TO HARDENING UNDER INFLUENCE OF HEAT AND AIR - PART 2: TFOT METHOD |
| 13/30255319 DC : 0 | BS EN 12607-2 - BITUMEN AND BITUMINOUS BINDERS - DETERMINATION OF THE RESISTANCE TO HARDENING UNDER THE INFLUENCE OF HEAT AND AIR - PART 2: TFOT METHOD |
| CGSB 16.3 : M90 | ASPHALT CEMENTS FOR ROAD PURPOSES |
| ASTM D 4383 : 2018 | Standard Specification for Plowable, Raised Retroreflective Pavement Markers |
| ASTM D 5710/D5710M : 2015 : REDLINE | Standard Specification for Trinidad Lake Modified Asphalt |
| ASTM D 5505 : 2014 : REDLINE | Standard Practice for Classifying Emulsified Recycling Agents |
| DIN EN 12607-2:2015-01 | BITUMEN AND BITUMINOUS BINDERS - DETERMINATION OF THE RESISTANCE TO HARDENING UNDER INFLUENCE OF HEAT AND AIR - PART 2: TFOT METHOD |
| UNE-EN 12607-2:2015 | Bitumen and bituminous binders - Determination of the resistance to hardening under influence of heat and air - Part 2: TFOT method |
| ASTM D 4552/D4552M : 2010 : R2016 : EDT 1 | Standard Practice for Classifying Hot-Mix Recycling Agents |
| ASTM D 4383 : 2012-12 | SPECIFICATION FOR PLOWABLE, RAISED RETROREFLECTIVE PAVEMENT MARKERS |
| BS EN 12607-2:2014 | Bitumen and bituminous binders. Determination of the resistance to hardening under influence of heat and air TFOT method |
| EN 12607-2:2014 | Bitumen and bituminous binders - Determination of the resistance to hardening under influence of heat and air - Part 2: TFOT method |
| ASTM E 1 : 2014 : REDLINE | Standard Specification for ASTM Liquid-in-Glass Thermometers |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.