• Shopping Cart
    There are no items in your cart

ASTM D 1998 : 2015

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Specification for Polyethylene Upright Storage Tanks

Available format(s)

Hardcopy , PDF

Superseded date

20-08-2021

Superseded by

ASTM D 1998 : 2021

Language(s)

English

Published date

05-11-2015

€67.30
Excluding VAT

Committee
D 20
DocumentType
Standard
Pages
8
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This specification covers flat-bottom, upright, cylindrical tanks molded in one-piece seamless construction by rotational molding. The tanks are molded from polyethylene for above ground, vertical installation and are capable of containing aggressive chemicals at atmospheric pressure. Included are requirements for materials, properties, design, construction, dimensions, tolerances, workmanship and appearance. Tank capacities are from 1900 L (500 gal) up.

1.2This specification covers the design of stationery vessels for use at atmospheric pressure intended for use with liquids heated below their flash points and continuous service temperatures below 66°C (150°F) for Type I tanks and below 60°C (140°F) for Type II tanks.

1.2.1NFPA Standards 30 and NFPA 31 shall be consulted for installations that are subject to the requirements of these standards.

1.3For service requirements beyond the scope of this specification (1.2), such as externally imposed mechanical forces, internal pressure or vacuum, higher temperature service, etc., other relevant sources of standards, for example, local and state building codes, NFPA, ASME, ARM, etc., shall be consulted.

1.4The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

Note 1:ISO 13341:2005+A1:2011 and ISO 13575:2012 are similar, but not equivalent to this standard.

1.5The following precautionary caveat pertains only to the test methods portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM D 2765 : 2016 Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics

ASTM D 2837 : 2013 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 4703 : 2002 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
ASTM D 1693 : 2000 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
ASTM D 3892 : 2015 : R2020 Standard Practice for Packaging/Packing of Plastics
ASTM D 2837 : 2001 : REV A Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
ASTM D 3892 : 1993 : R2003 Standard Practice for Packaging/Packing of Plastics
ASTM D 3892 : 2015 Standard Practice for Packaging/Packing of Plastics
ASTM D 4703 : 2003 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
ASTM D 2837 : 2002 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
ASTM D 2837 : 2001 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
ASTM D 1693 : 2008 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
ASTM D 2837 : 2004 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 3892 : 1993 : R1998 Standard Practice for Packaging/Packing of Plastics
ASTM D 2837 : 2021 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM E 691 : 2020 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 4703 : 1993 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
ASTM D 1693 : 2015 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
ASTM D 1693 : 2012 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
ASTM D 1693 : 1994 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
ASTM D 2837 : 2008 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 2837 : 1998 : REV A Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
ASTM E 691 : 2019 : EDT 1 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 4703 : 2010 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
ASTM D 2837 : 2001 : REV A : EDT 1 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
ASTM D 2837 : 2011 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 1693 : 2005 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
ASTM E 691 : 2009 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 618 : 2013 Standard Practice for Conditioning Plastics for Testing
ASTM D 1693 : 2007 : REV A Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
ASTM D 3892 : 1993 : R2009 Standard Practice for Packaging/Packing of Plastics
ASTM D 4703 : 2000 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
ASTM D 4703 : 2010 : REV A Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
ASTM D 4703 : 2016 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
ASTM D 1693 : 2001 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
ASTM D 1693 : 2013 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
ASTM D 618 : 2021 Standard Practice for Conditioning Plastics for Testing
ASTM D 4703 : 2007 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
ASTM D 1693 : 2007 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
ASTM D 2837 : 2013 : EDT 1 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 2837 : 2004 : EDT 1 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.