• Shopping Cart
    There are no items in your cart

ASTM D 3045 : 1992 : R1997

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Practice for Heat Aging of Plastics Without Load

Available format(s)

Hardcopy , PDF

Superseded date

03-11-2018

Language(s)

English

Published date

10-11-1997

€67.30
Excluding VAT

CONTAINED IN VOL. 08.02, 2015 Describes the exposure conditions for testing the resistance of plastics to oxidation or other degradation when exposed solely to hot air for extended periods of time.

Committee
D 20
DocumentType
Standard Practice
Pages
5
ProductNote
Reconfirmed 1997 Reconfirmed 2016
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

1.1 This practice is intended to define the exposure conditions for testing the resistance of plastics to oxidation or other degradation when exposed solely to hot air for extended periods of time. Only the procedure for heat exposure is specified, not the test method or specimen. The effect of heat on any particular property may be determined by selection of the appropriate test method and specimen.

1.2 This practice should be used as a guide to compare thermal aging characteristics of materials as measured by the change in some property of interest. This practice recommends procedures for comparing the thermal aging characteristics of materials at a single temperature. Recommended procedures for determining the thermal aging characteristics of a material at a series of temperatures for the purpose of estimating time to a defined property change at some lower temperature are also described.

1.3 This practice does not predict thermal aging characteristics where interactions between stress, environment, temperature, and time control failure occurs.

1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note-ISO-2578 is considered to be technically equivalent to this practice.

ASTM D7444 : 2018 : REV A Standard Practice for Heat and Humidity Aging of Oxidatively Degradable Plastics<br>
ASTM D 5721 : 2008 : R2018 Standard Practice for Air-Oven Aging of Polyolefin Geomembranes
ASTM D 5592 : 1994 : R2018 Standard Guide for Material Properties Needed in Engineering Design Using Plastics
ASTM D 4434/D4434M : 2015 Standard Specification for Poly(Vinyl Chloride) Sheet Roofing
ASTM D 3105 : 2017 Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials
ASTM D 5870 : 2016 Standard Practice for Calculating Property Retention Index of Plastics
ASTM G 114 : 2014 Standard Practices for Evaluating the Age Resistance of Polymeric Materials Used in Oxygen Service
ASTM C 1173 : 2018 Standard Specification for Flexible Transition Couplings for Underground Piping Systems
ASTM D 6754/D6754M : 2015 Standard Specification for Ketone Ethylene Ester Based Sheet Roofing
ASTM E 2785 : 2014 Standard Test Method for Exposure of Firestop Materials to Severe Environmental Conditions
ASTM E 2925 : 2017 Standard Specification for Manufactured Polymeric Drainage and Ventilation Materials Used to Provide a Rainscreen Function

ISO 505:2017 Conveyor belts — Method for the determination of the tear propagation resistance of textile conveyor belts
ISO 2578:1993 Plastics Determination of time-temperature limits after prolonged exposure to heat
ASTM D 1870 : 1991 Practice for Elevated Temperature Aging Using a Tubular Oven (Withdrawn 1998)
ASTM D 1894 : 2014 : REDLINE Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
ASTM D 618 : 2013 : REDLINE Standard Practice for Conditioning Plastics for Testing
ISO 7590:2009 Steel cord conveyor belts Methods for the determination of total thickness and cover thickness
ISO 282:1992 Conveyor belts — Sampling
ISO 7622-2:2015 Steel cord conveyor belts Longitudinal traction test Part 2: Measurement of tensile strength
ISO 8094:2013 Steel cord conveyor belts — Adhesion strength test of the cover to the core layer
ASTM D 1149 : 2016-02 TEST METHODS FOR RUBBER DETERIORATION - CRACKING IN AN OZONE CONTROLLED ENVIRONMENT
ISO 4649:2017 Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating cylindrical drum device
ASTM D 3183 : 201 PRACTICE FOR RUBBER - PREPARATION OF PIECES FOR TEST PURPOSES FROM PRODUCTS
ISO 9856:2016 Conveyor belts Determination of elastic and permanent elongation and calculation of elastic modulus
ASTM D 413 : 1998 Standard Test Methods for Rubber Property-Adhesion to Flexible Substrate
ARPM IP1 : 2011 CONVEYOR AND ELEVATOR BELT HANDBOOK
ISO 7623:2015 Steel cord conveyor belts — Cord-to-coating bond test — Initial test and after thermal treatment
ISO 340:2013 Conveyor belts Laboratory scale flammability characteristics Requirements and test method
ISO 283:2015 Textile conveyor belts — Full thickness tensile strength, elongation at break and elongation at the reference load — Test method
ISO 284:2012 Conveyor belts — Electrical conductivity — Specification and test method
ASTM D 865 : 2011 Standard Test Method for Rubber<char: emdash>Deterioration by Heating in Air (Test Tube Enclosure)
CFR 30(PTS1-199) : JUL 2017 MINERAL RESOURCES - MINE SAFETY & HEALTH ADMINISTRATION, DEPARTMENT OF LABOUR
ISO 7622-1:2013 Steel cord conveyor belts — Longitudinal traction test — Part 1: Measurement of elongation
ASTM D 4483 : 2014-02 PRACTICE FOR EVALUATING PRECISION FOR TEST METHOD STANDARDS IN THE RUBBER AND CARBON BLACK MANUFACTURING INDUSTRIES
ASTM D 471 : 2016-02 TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.