ASTM D 3278 : 1996 : R2004 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
Hardcopy , PDF
11-11-2014
English
01-11-2004
CONTAINED IN VOL. 06.01, 2017 Specifies procedures for determining whether a material does or does not flash at a specified temperature or for determining the lowest finite temperature at which a material does flash when using a small scale closed-cup apparatus.
Committee |
D 01
|
DocumentType |
Test Method
|
Pages |
8
|
ProductNote |
Reconfirmed EDT 1
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1 These test methods cover procedures for determining whether a material does or does not flash at a specified temperature or for determining the lowest finite temperature at which a material does flash when using a small scale closed-cup apparatus. The test methods are applicable to paints, enamels, lacquers, varnishes, and related products having a flash point between 0 and 110C (32 and 230F) and viscosity lower than 150 St at 25C (77F). Note 1Tests at higher or lower temperatures are possible.
Note 2More viscous materials may be tested in accordance with .
Note 3Organic peroxides may be tested in accordance with , which describes the applicable safety precautions.
Note 4The U.S. Department of Labor (OSHA, Hazard Communications), the U.S. Department of Transportation (RSPA), and the U.S. Environmental Protection Agency (EPA) have specified Test Methods D 3278 as one of several acceptable methods for the determination of flash point of liquids in their regulations.
Note 5These test methods are similar to International Standards ISO 3679 and ISO 3680.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard should be used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions and should not be used to describe or appraise the fire-hazard or fire-risk of materials, products, or assemblies under actual fire conditions. However, results of the test may be used as elements of a fire-hazard or a fire-risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard or fire risk of a particular end use
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D 3730 : 2017 | Standard Guide for Testing High-Performance Interior Architectural Wall Coatings |
ASTM D 6577 : 2015 | Standard Guide for Testing Industrial Protective Coatings |
ASTM F 718 : 2007 : R2017 | Standard Specification for Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet |
ASTM D 3105 : 2017 | Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials |
ASTM D 3734 : 2005 : R2018 | Standard Specification for High-Flash Aromatic Naphthas |
ASTM D 333 : 2001 : R2013 | Standard Guide for Clear and Pigmented Lacquers |
ASTM D 6763 : 2016 | Standard Guide for Testing Exterior Wood Stains and Clear Water Repellents |
ASTM D 56 : 2016 : REV A | Standard Test Method for Flash Point by Tag Closed Cup Tester |
ASTM D 3757 : 2016 | Standard Guide for Preparing Specifications for Solvent-based Floor Polishes |
ASTM D 3794 : 2018 | Standard Guide for Testing Coil Coatings |
ASTM E 1232 : 2007 : R2019 | Standard Test Method for Temperature Limit of Flammability of Chemicals |
ASTM D 235 : 2002 : R2012 | Standard Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent) (Withdrawn 2021) |
ASTM D 115 : 2017 | Standard Test Methods for Testing Solvent Containing Varnishes Used for Electrical Insulation |
ASTM D 3934 : 2014 | Standard Test Method for Flash/No Flash Test—Equilibrium Method by a Closed-Cup Apparatus |
ASTM D 3955 : 2013 | Standard Specification for Electrical Insulating Varnishes |
ASTM D 803 : 2015 | Standard Test Methods for Testing Tall Oil |
ASTM D 268 : 2001 : R2012 | Standard Guide for Sampling and Testing Volatile Solvents and Chemical Intermediates for Use in Paint and Related Coatings and Material (Withdrawn 2021) |
ASTM F 940 : 1999 : R2013 | Standard Practice for Quality Control Receipt Inspection Procedures for Protective Coatings (Paint), Used in Marine Construction and Shipbuilding |
ASTM E 502 : 2007 : R2013 | Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods |
ASTM D 3735 : 2007 : R2012 | Standard Specification for VM&P Naphthas (Withdrawn 2021) |
ASTM D 4800 : 1994 : R2015 | Standard Guide for Classifying and Specifying Adhesives |
ASTM D 6361/D6361M : 1998 : R2015 | Standard Guide for Selecting Cleaning Agents and Processes |
ASTM D 6465 : 1999 : R2016 | Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants |
ASTM C 461 : 2017 | Standard Test Methods for Mastics and Coatings Used With Thermal Insulation |
ISO 3679:2015 | Determination of flash no-flash and flash point — Rapid equilibrium closed cup method |
ASTM D 93 : 2016-07 | TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER |
ISO 3680:2004 | Determination of flash/no flash Rapid equilibrium closed cup method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.