• Shopping Cart
    There are no items in your cart

ASTM D 3278 : 2020

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus

Available format(s)

Hardcopy , PDF

Superseded date

13-08-2021

Superseded by

ASTM D 3278 : 2021

Language(s)

English

Published date

16-06-2020

€67.30
Excluding VAT

Committee
D 01
DocumentType
Test Method
Pages
8
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1These test methods cover procedures for determining whether a material does or does not flash at a specified temperature or for determining the lowest finite temperature at which a material does flash when using a small scale closed-cup apparatus.2 The test methods are applicable to paints, enamels, lacquers, varnishes, and related products having a flash point between 0 and 110°C (32 and 230°F) and viscosity lower than 150 St at 25°C (77°F).

Note 1:Tests at higher or lower temperatures are possible.

Note 2:More viscous materials may be tested in accordance with Annex A4.

Note 3:Organic peroxides may be tested in accordance with Annex A5, which describes the applicable safety precautions.

Note 4:The U.S. Department of Labor (OSHA, Hazard Communications), the U.S. Department of Transportation (RSPA), and the U.S. Environmental Protection Agency (EPA) have specified Test Methods D3278 as one of several acceptable methods for the determination of flash point of liquids in their regulations.

Note 5:These test methods are similar to International Standards ISO 3679 and ISO 3680.

1.2The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.3This standard should be used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions and should not be used to describe or appraise the fire-hazard or fire-risk of materials, products, or assemblies under actual fire conditions. However, results of the test may be used as elements of a fire-hazard or a fire-risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard or fire risk of a particular end use.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 8.1 and 11.2.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D 3794 : 2018 Standard Guide for Testing Coil Coatings
ASTM E 1232 : 2007 : R2019 Standard Test Method for Temperature Limit of Flammability of Chemicals
ASTM D 115 : 2017 Standard Test Methods for Testing Solvent Containing Varnishes Used for Electrical Insulation
ASTM D 3955 : 2013 Standard Specification for Electrical Insulating Varnishes
ASTM D 803 : 2015 Standard Test Methods for Testing Tall Oil
ASTM D 268 : 2001 : R2012 Standard Guide for Sampling and Testing Volatile Solvents and Chemical Intermediates for Use in Paint and Related Coatings and Material (Withdrawn 2021)
ASTM E 502 : 2007 : R2013 Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods
ASTM D 3735 : 2007 : R2012 Standard Specification for VM&P Naphthas (Withdrawn 2021)
ASTM D 4800 : 1994 : R2015 Standard Guide for Classifying and Specifying Adhesives
ASTM D 6465 : 1999 : R2016 Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants
ASTM C 461 : 2017 Standard Test Methods for Mastics and Coatings Used With Thermal Insulation
ASTM D 3730 : 2017 Standard Guide for Testing High-Performance Interior Architectural Wall Coatings
ASTM D 235 : 2002 : R2012 Standard Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent) (Withdrawn 2021)
ASTM F 718 : 2007 : R2017 Standard Specification for Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet
ASTM D 3105 : 2017 Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials
ASTM D 3734 : 2005 : R2018 Standard Specification for High-Flash Aromatic Naphthas
ASTM D 333 : 2001 : R2013 Standard Guide for Clear and Pigmented Lacquers
ASTM D 6763 : 2016 Standard Guide for Testing Exterior Wood Stains and Clear Water Repellents
ASTM D 6577 : 2015 : R2019 Standard Guide for Testing Industrial Protective Coatings
ASTM D 56 : 2016 : REV A Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM D 3757 : 2016 Standard Guide for Preparing Specifications for Solvent-based Floor Polishes
ASTM F 940 : 1999 : R2019 : EDT 1 Standard Practice for Quality Control Receipt Inspection Procedures for Protective Coatings (Paint), Used in Marine Construction and Shipbuilding
ASTM D 803 : 2015 : R2020 Standard Test Methods for Testing Tall Oil
ASTM D 3934 : 2020 Standard Test Method for Flash/No Flash Test—Equilibrium Method by a Closed-Cup Apparatus
ASTM D 6361/D6361M : 1998 : R2020 Standard Guide for Selecting Cleaning Agents and Processes
ASTM D 5146 : 2010 : R2019 Standard Guide to Testing Solvent-Borne Architectural Coatings
ASTM D 3955 : 2020 Standard Specification for Electrical Insulating Varnishes
ASTM D 333 : 2001 : R2021 Standard Guide for Clear and Pigmented Lacquers
ASTM D 4733 : 2017 Standard Test Methods for Solventless Electrical Insulating Varnishes

ASTM D 93 : 1990 : EDT 1 Standard Test Methods for Flash Point by Pensky-Martens Closed Tester
ASTM D 850 : 2018 : EDT 1 Standard Test Method for Distillation of Industrial Aromatic Hydrocarbons and Related Materials
ASTM D 56 : 2021 Standard Test Method for Flash Point by Tag Closed Cup Tester
ASTM D 93 : 2000 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester
ASTM D 93 : 1985 Standard Test Method for Flash Point by Pensky-Martens Closed Tester
ASTM D 850 : 2002 Standard Test Method for Distillation of Industrial Aromatic Hydrocarbons and Related Materials
ASTM D 56 : 1987 Standard Test Method for Flash Point by Tag Closed Tester
ASTM D 93 : 1997 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester
ASTM D 850 : 2021 Standard Test Method for Distillation of Industrial Aromatic Hydrocarbons and Related Materials

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.