• Shopping Cart
    There are no items in your cart

ASTM D 3517 : 2019

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe

Available format(s)

Hardcopy , PDF

Superseded date

11-06-2024

Superseded by

ASTM D 3517 : 2024

Language(s)

English

Published date

01-08-2019

€74.48
Excluding VAT

This specification covers machine-made fiberglass pipe, 8 in. (200 mm) through 156 in. (4000 mm), intended for use in water conveyance systems which operate at internal gage pressures of 450 psi (3103 kPa) or less.

Committee
D 20
DocumentType
Standard
Pages
13
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This specification covers machine-made fiberglass pipe, 8 in. (200 mm) through 156 in. (4000 mm), intended for use in water conveyance systems which operate at internal gage pressures of 450 psi (3103 kPa) or less. Both glass-fiber-reinforced thermosetting-resin pipe (RTRP) and glass-fiber-reinforced polymer mortar pipe (RPMP) are fiberglass pipes. The standard is suited primarily for pipes to be installed in buried applications, although it may be used to the extent applicable for other installations such as, but not limited to, jacking, tunnel lining and slip-lining rehabilitation of existing pipelines.

Note 1:For the purposes of this standard, polymer does not include natural polymers.

1.2The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.

Note 2:There is no known ISO equivalent to this standard.

1.3The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D 1599 : 2018 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 5421 : 2015 Standard Specification for Contact Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges
ASTM D 5421 : 2023 Standard Specification for Contact Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges

ASTM D 4161 : 1996 Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals
ASTM D 883 : 2023 Standard Terminology Relating to Plastics
ASTM D 2290 : 2019 : REV A Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
ASTM C 33/C33M : 2023 Standard Specification for Concrete Aggregates
ASTM D 3892 : 2015 : R2020 Standard Practice for Packaging/Packing of Plastics
ASTM F 412 : 2020 : REV A Standard Terminology Relating to Plastic Piping Systems
ASTM F 477 : 2014 Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
ASTM F 412 : 2021 Standard Terminology Relating to Plastic Piping Systems
ASTM D 2992 : 2022 Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
ASTM D 883 : 2024 Standard Terminology Relating to Plastics
ASTM C 33/C33M : 2018 Standard Specification for Concrete Aggregates
ASTM F 477 : 2002 Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
ASTM D 3892 : 2015 Standard Practice for Packaging/Packing of Plastics
ASTM D 883 : 2022 Standard Terminology Relating to Plastics
ASTM D 883 : 2020 : REV B Standard Terminology Relating to Plastics
ASTM D 3567 : 2017 : R2022 Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
ASTM F 477 : 2014 : R2021 Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
ASTM D 638 : 2014 Standard Test Method for Tensile Properties of Plastics
ASTM D 2412 : 2021 Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
ASTM D 1600 : 2018 Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
ASTM F 412 : 2023 Standard Terminology Relating to Plastic Piping Systems
ASTM D 695 : 2015 Standard Test Method for Compressive Properties of Rigid Plastics
ASTM D 2290 : 2019 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
ASTM D 4161 : 2014 : R2019 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals
ASTM D 3567 : 2017 Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
ASTM D 695 : 2023 Standard Test Method for Compressive Properties of Rigid Plastics
ASTM D 2412 : 2011 : R2018 Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
ASTM D 2992 : 2018 Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
ASTM D 638 : 2022 Standard Test Method for Tensile Properties of Plastics

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.