ASTM D 3730 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Guide for Testing High-Performance Interior Architectural Wall Coatings
Hardcopy , PDF
23-12-2022
English
27-06-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
D 01
|
| DocumentType |
Guide
|
| Pages |
10
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This guide covers the selection and use of test methods for high-performance interior architectural wall coatings (HIPAC) that differ from more conventional coatings by being tougher, more stain-resistant, more abrasion-resistant and, ordinarily, designed to be applied to wall surfaces of steel, masonry (poured concrete, concrete block, or cinder block), and plaster or gypsum wallboard. The tests that are listed in Table 1 and Table 2 are designed to measure performance properties. These tests may not all be required for each HIPAC system. Selection of the test methods to be followed must be governed by experience and the requirements in each individual case, together with agreement between the purchaser and the seller.
1.2High-performance architectural coatings are tough, extra-durable organic coating systems that are applied as a continuous (seamless) film and cure to a hard finish. The finish can be high gloss, semigloss, or low gloss as desired. These coatings are resistant to persistent heat, humidity, abrasion, staining, chemicals, and fungus growth. They are used in areas where humidity, wear, or unusual chemical resistance requirements, particularly to soiling, are required and where strong detergents are used to maintain sanitary conditions. Halls and stairways in public buildings, lavatories, stall showers, locker areas, animal pens, and biological laboratories are typical applications. In addition, food processing plants, dairies, restaurants, schools, and transport terminals frequently use HIPAC systems. These are effective in many areas of building interiors compared with tile and are of low materials and maintenance costs. They are used as a complete system only as recommended by the manufacturer since the individual coats in a system are formulated to be compatible with each other. HIPAC systems should be applied only to properly prepared surfaces such as steel or masonry, including cinder blocks and cement blocks. They can be applied over plaster and gypsum wallboard. Ordinarily, a prime or fill coat, if required, is part of the system.
1.3While they are excellent for walls, HIPAC are not usually intended for ceilings and floors. They would not ordinarily be used in homes, although parents with small children might want to use HIPAC coatings on some walls.
1.4The types of resin ordinarily used are the following: epoxy-polyamide, two-package; polyester-epoxy, two-package; polyurethane, one-package or two-package. However, other resin types are not excluded provided they can meet the requirements (performance specifications) laid down by the purchaser.
1.5The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
TABLE 1 List of Standards in Sectional Order
| Property | Section | ASTM | Federal |
| Sampling: | 5.2 | D3925 | ... |
| Liquid Paint Properties: | |||
| Skinning | 7.1 | D154 | |
| Condition in container | 7.2 | ... | 3011 |
| Coarse particles and foreign matter | 7.3 | D185 | |
| Density or weight per gallon | 7.4 | D1475 | |
| Fineness of dispersion | 7.5 | D1210 | |
| Flash point | 7.7 | D93, D3278 | |
| Dilution stability | 7.8 | ... | 4203 |
| Volatile content | 7.9 | D2369 | ... |
| Free diisocyanate content | 7.10 | D3432 | ... |
| Package stability | 7.11 | ||
| Heat stability | 7.11.1 | D1849 | |
| Settling | 7.11.2 | D869 | |
| Color Acceptance | 7.12 | D5326 | |
| Coating Application and Film Formation: | |||
| Application properties | 8.1 | ... | 4541 |
| Brush application | 8.1.1 | ... | 2141 |
| Brush drag | 8.1.1.1 | D4958 | ... |
| Roller application | 8.1.2 | ... | 2112 |
| Roller spatter | 8.1.2.1 | D4707 | ... |
| Spray application | 8.1.3 | ... | 2131 |
| Open time | 8.1.4 | D7488 | |
| Rheological properties | 8.2 | ... | ... |
| Consistency (low-shear viscosity) | 8.2.1 | D562 | ... |
| Rheological properties of non-Newtonian liquids | 8.2.2 | D2196, D4287 | ... |
| Sag resistance | 8.2.3 | D4400 | ... |
| Leveling properties | 8.2.4 | D4062 | ... |
| Curing properties | 8.3 | ... | ... |
| Wet-film thickness | 8.4 | D1212 | ... |
| Touch-up uniformity | 8.5 | D3928, D7489 | |
| Low Temperature Coalescence | 8.6 | D3793, D7306 | |
| Enamel holdout | 8.7 | D7786 | |
| Appearance of Dry Coating: | |||
| Color appearance | 9.1.1 | ... | ... |
| Color differences by visual comparison | 9.1.2 | D1729 | ... |
| Color differences using instrumental | 9.1.3 | D2244 | ... |
| Directional reflectance | 9.2 | E1347 | ... |
| Gloss, 60° | 9.3 | D523 | ... |
| Hiding power | 9.4 | D344, D2805, D5150 | ... |
| Yellowness index | 9.5 | E313 | |
| Properties of Dry Film: | |||
| Abrasion resistance | 10.1 | D4060 | ... |
| Adhesion | 10.2 | D4541 | ... |
| Wet Adhesion | 10.2.1 | D6900 | 6301 |
| Impact resistance | 10.3 | D2794 | ... |
| Chemical resistance | 10.4 | D1308 | ... |
| Washability and cleansability | 10.5 | ... | ... |
| Washability | 10.5.1 | D2486, D4213 | ... |
| Cleansability | 10.5.2 | D3450, D4828 | ... |
| Stainblocking | 10.6 | D7514 | |
| Mildew resistance | 10.7 | D3273 | ... |
| Perspiration resistance | 10.8 | ... | ... |
| Heat and cold resistance | 10.9 | D1211 | ... |
| Heat and humidity resistance | 10.10 | D2247 | ... |
| Fire hazards | 10.11 | E84 | |
| Dry-film thickness | 10.12 | D1005, D1186, D1400 | |
| Burnish Resistance | 10.13 | D6736 |
TABLE 2 Alphabetical List of Test Methods
| Test Method | Section | ASTM | Federal Test |
| Abrasion resistance | 10.1 | D4060 | |
| Adhesion | 10.2 | D4541 | ... |
| Application properties | 8.1 | ... | 4541 |
| Brush application | 8.1.1 | ... | 2141 |
| Brush drag | 8.1.1.1 | D4958 | ... |
| Burnish Resistance | 10.13 | D6736 | |
| Chemical resistance | 10.4 | D1308A | ... |
| Cleansability | 10.5.2 | D3450, D4828 | ... |
| Coarse particles and foreign matter | 7.3 | D185 | |
| Color Acceptance | 7.12 | D5326 | |
| Color appearance | 9.1.1 | ... | ... |
| Color differences by visual comparison | 9.1.2 | D1729 | ... |
| Color differences using instrumental | 9.1.3 | D2244 | ... |
| Condition in container | 7.2 | ... | 3011 |
| Consistency (low-shear viscosity) | 8.2.1 | D562 | ... |
| Curing properties | 8.3 | ... | ... |
| Density or weight per gallon | 7.4 | D1475 | ... |
| Dilution stability | 7.8 | ... | 4203 |
| Directional reflectance | 8.2 | E1347 | ... |
| Dry-film thickness | 10.12 | D1005, D1186, D1400 | ... |
| Enamel holdout | 8.7 | D7786 | |
| Fineness of dispersion | 7.5 | D1210 | ... |
| Fire hazards | 10.11 | E84 | |
| Flash point | 7.7 | D93, D3278 | ... |
| Free diisocyanate content | 7.10 | D3432 | |
| Gloss (60-deg specular) | 9.3 | D523 | |
| Heat and cold resistance | 10.9 | D1211A | ... |
| Heat and humidity resistance | 10.10 | D2247A | ... |
| Heat stability | 7.11.1 | D1849 | |
| Hiding power | 9.4 | D344, D2805, D5150 | ... |
| Impact resistance | 10.3 | ... | ... |
| Leveling properties | 8.2.4 | D4062 | ... |
| Low Temperature Coalescence | 8.6 | D3793, D7306 | ... |
| Mildew resistance | 10.7 | D3273 | ... |
| Open time of latex | 8.1.4 | D7488 | |
| Package stability | 7.11 |
| |
| Perspiration resistance | 10.8 | ... | ... |
| Rheological properties of non-Newtonian liquids | 8.2.2 | D2196, D4287 | ... |
| Roller application | 8.1.2 | ... | 2112 |
| Roller spatter | 8.1.2.1 | D4707 | ... |
| Sag resistance | 8.2.3 | D4400 | ... |
| Sampling | 5.2 | D3925 | ... |
| Settling | 7.11.2 | D869 | |
| Skinning | 7.1 | D154 | |
| Spray application | 8.3 | ... | 2131 |
| Stainblocking | 10.6 | D7514 | |
| Touch-up uniformity | 8.5 | D3928, D7489 | |
| Volatile content | 7.9 | D2369 | ... |
| Washability | 10.5.1 | D2486, D4213 | ... |
| Wet Adhesion | 10.2.1 | D6900 | 6301 |
| Wet-film thickness | 8.4 | D1212 | ... |
| Yellowness index | 9.5 | E313 |
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see the note in 7.6.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM G 195 : 2022 | Standard Guide for Conducting Wear Tests Using a Rotary Platform Abraser |
| ASTM G 195 : 2018 | Standard Guide for Conducting Wear Tests Using a Rotary Platform Abraser |
| ASTM D 5146 : 2010 : R2019 | Standard Guide to Testing Solvent-Borne Architectural Coatings |
| ASTM D 5324 : 2016 | Standard Guide for Testing Water-Borne Architectural Coatings |
| ASTM D 2196 : 2015 | Standard Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational Viscometer |
| ASTM D 1212 : 1991 : R2013 | Standard Test Methods for Measurement of Wet Film Thickness of Organic Coatings |
| ASTM D 1005 : 1995 : R2020 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
| ASTM D 4062 : 1999 | Standard Test Method for Leveling of Paints by Draw-Down Method |
| ASTM D 3928 : 2000 : REV A : R2018 | Standard Test Method for Evaluation of Gloss or Sheen Uniformity |
| ASTM D 5326 : 1994 : REV A : R2009 | Standard Test Method for Color Development in Tinted Latex Paints |
| ASTM D 3278 : 2020 | Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus |
| ASTM D 6900 : 2010 : R2015 | Standard Test Method for Wet Adhesion of Latex Paints to a Gloss Alkyd Enamel Substrate |
| ASTM D 1475 : 2013 | Standard Test Method For Density of Liquid Coatings, Inks, and Related Products |
| ASTM D 1210 : 1996 | Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type Gage |
| ASTM D 2196 : 2010 | Standard Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational (Brookfield type) Viscometer |
| ASTM D 1475 : 1998 : R2012 | Standard Test Method For Density of Liquid Coatings, Inks, and Related Products |
| ASTM D 4213 : 2008 | Standard Test Method for Scrub Resistance of Paints by Abrasion Weight Loss |
| ASTM D 2244 : 2021 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 7306 : 2007 : R2017 | Standard Practice for Testing Low Temperature Film-Formation of Latex Paints by Visual Observation |
| ASTM D 4400 : 1999 : R2012 | Standard Test Method for Sag Resistance of Paints Using a Multinotch Applicator |
| ASTM D 2247 : 2010 | Standard Practice for Testing Water Resistance of Coatings in 100% Relative Humidity |
| ASTM E 1347 : 2006 : R2020 | Standard Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry |
| ASTM D 4828 : 1994 : R2008 | Standard Test Methods for Practical Washability of Organic Coatings |
| ASTM D 4541 : 2009 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 3273 : 2000 : R2005 | Standard Test Method for Resistance to Growth of Mold on the Surface of Interior Coatings in an Environmental Chamber |
| ASTM D 1296 : 2001 | Standard Test Method for Odor of Volatile Solvents and Diluents |
| ASTM D 2244 : 2015 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 3273 : 2012 : EDT 1 | Standard Test Method for Resistance to Growth of Mold on the Surface of Interior Coatings in an Environmental Chamber |
| ASTM D 2196 : 2005 | Standard Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational (Brookfield type) Viscometer |
| ASTM D 1308 : 2002 : R2013 | Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes |
| ASTM D 4213 : 2008 : R2016 | Standard Test Method for Scrub Resistance of Paints by Abrasion Weight Loss |
| ASTM D 3925 : 1981 : R1985 | Standard Practice for Sampling Liquid and Related Pigmented Coatings |
| ASTM D 3273 : 2012 | Standard Test Method for Resistance to Growth of Mold on the Surface of Interior Coatings in an Environmental Chamber |
| ASTM D 1475 : 1985 | Standard Test Method for Density of Paint, Varnish, Lacquer, and Related Products |
| ASTM D 869 : 2021 | Standard Test Method for Evaluating Degree of Settling of Paint |
| ASTM D 3928 : 2000 : REV A : R2014 | Standard Test Method for Evaluation of Gloss or Sheen Uniformity |
| ASTM D 2369 : 1998 | Standard Test Method for Volatile Content of Coatings |
| ASTM D 6736 : 2008 : R2013 | Standard Test Method for Burnish Resistance of Latex Paints |
| ASTM D 2244 : 2011 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 3278 : 1996 : EDT 1 | Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus |
| ASTM D 4400 : 1999 : R2007 | Standard Test Method for Sag Resistance of Paints Using a Multinotch Applicator |
| ASTM D 3925 : 1991 : R1996 | Standard Practice for Sampling Liquid Paints and Related Pigmented Coatings |
| ASTM D 1729 : 2016 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM D 869 : 1985 : R2015 | Standard Test Method for Evaluating Degree of Settling of Paint |
| ASTM D 2805 : 2011 : R2018 | Standard Test Method for Hiding Power of Paints by Reflectometry |
| ASTM D 3273 : 1986 : R1991 : EDT 1 | Standard Test Method for Resistance to Growth of Moid on the Surface of Interior Coatings in an Enviormental Chamber |
| ASTM D 3793 : 2004 | Standard Test Method for Low-Temperature Coalescence of Latex Paint Films |
| ASTM D 4062 : 2011 : R2016 | Standard Test Method for Leveling of Paints by Draw-Down Method |
| ASTM D 2244 : 2009 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 5150 : 1992 : R2013 | Standard Test Method for Hiding Power of Architectural Paints Applied by Roller |
| ASTM D 1212 : 1991 : R2007 : EDT 1 | Standard Test Methods for Measurement of Wet Film Thickness of Organic Coatings |
| ASTM E 1347 : 2006 : R2015 | Standard Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry |
| ASTM D 7488 : 2010 | Standard Test Method for Open Time of Latex Paints |
| ASTM D 2247 : 2011 | Standard Practice for Testing Water Resistance of Coatings in 100% Relative Humidity |
| ASTM D 1212 : 1991 : R2020 | Standard Test Methods for Measurement of Wet Film Thickness of Organic Coatings |
| ASTM D 5150 : 1992 : R2009 | Standard Test Method for Hiding Power of Architectural Paints Applied by Roller |
| ASTM D 2244 : 2002 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 2247 : 2002 | Standard Practice for Testing Water Resistance of Coatings in 100% Relative Humidity |
| ASTM D 4828 : 1994 : R2016 | Standard Test Methods for Practical Washability of Organic Coatings |
| ASTM D 2244 : 2016 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 7306 : 2007 | Standard Practice for Testing Low Temperature Film-Formation of Latex Paints by Visual Observation |
| ASTM D 4060 : 2007 | Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser |
| ASTM D 2794 : 1992 | Standard Test Method for Resistence of Organic Coatings to the Effects of Rapid Deformation (Impact) |
| ASTM E 1347 : 2003 | Standard Test Method for Color and Color-Difference Measurement by Tristimulus (Filter) Colorimetry |
| ASTM D 2369 : 1981 : EDT 1 | Standard Test Method for Volatile Content of Coatings |
| ASTM D 4541 : 2009 : EDT 1 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 1296 : 2001 : R2012 | Standard Test Method for Odor of Volatile Solvents and Diluents (Withdrawn 2021) |
| ASTM D 5150 : 1992 : R1997 : EDT 1 | Standard Test Method for Hiding Power of Architectural Paints Applied by Roller |
| ASTM D 7786 : 2013 | Standard Test Method for Determining Enamel Holdout |
| ASTM D 2369 : 2001 | Standard Test Method for Volatile Content of Coatings |
| ASTM D 2244 : 2015 : EDT 1 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 2486 : 2006 | Standard Test Methods for Scrub Resistance of Wall Paints |
| ASTM D 2244 : 2009 : REV B | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 1186 : 1993 | Standard Test Methods for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to a Ferrous Base |
| ASTM D 1475 : 1998 : R2003 | Standard Test Method for Density of Liquid Coatings, Inks, and Related Products |
| ASTM D 2244 : 2002 : EDT 1 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 2247 : 1992 | Standard Practice for Testing Water Reistence of Coatings in 100% Relative Humidity |
| ASTM D 2369 : 2010 | Standard Test Method for Volatile Content of Coatings |
| ASTM E 84 : 2021 | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM D 1005 : 1995 : R2001 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
| ASTM D 93 : 1990 : EDT 1 | Standard Test Methods for Flash Point by Pensky-Martens Closed Tester |
| ASTM D 2244 : 2015 : REV A | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 3278 : 1982 : EDT 1 | Standard Test Methods for Flash Point of Liquids by Setaflash Closed-Cup Apparatus |
| ASTM E 105 : 2021 | Standard Guide for Probability Sampling of Materials |
| ASTM E 84 : 2022 | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM D 3278 : 2021 | Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus |
| ASTM D 2247 : 2015 | Standard Practice for Testing Water Resistance of Coatings in 100 % Relative Humidity |
| ASTM D 3432 : 1989 : R1996 : EDT 1 | Standard Test Method for Unreacted Toluene Diisocyanates in Urethane Prepolymers and Coating Solutions by Gas Chromatography (Withdrawn 2004) |
| ASTM D 3450 : 2000 : R2010 | Standard Test Method for Washability Properties of Interior Architectural Coatings |
| ASTM D 2486 : 2017 | Standard Test Methods for Scrub Resistance of Wall Paints |
| ASTM D 1210 : 2005 | Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type Gage |
| ASTM E 1347 : 1997 | Standard Test Method for Color and Color-Difference Measurement by Tristimulus (Filter) Colorimetry |
| ASTM D 1400 : 1994 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Nonconductive Coatings Applied to a Nonferrous Metal Base |
| ASTM D 4541 : 2002 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 1210 : 2005 : R2022 | Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type Gage |
| ASTM D 5150 : 1992 : R2017 | Standard Test Method for Hiding Power of Architectural Paints Applied by Roller |
| ASTM D 4585 : 1999 | Standard Practice for Testing Water Resistance of Coatings Using Controlled Condensation |
| ASTM D 6736 : 2001 | Standard Test Method for Burnish Resistance of Latex Paints |
| ASTM D 1729 : 1996 : R2009 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM D 7489 : 2009 : R2017 | Standard Practice for Evaluating Touch-Up Properties of Architectural Coatings under Various Environmental Conditions |
| ASTM D 7489 : 2009 | Standard Practice for Evaluating Touch-Up Properties of Architectural Coatings under Various Environmental Conditions |
| ASTM D 4828 : 1994 : R2003 : EDT 1 | Standard Test Methods for Practical Washability of Organic Coatings |
| ASTM D 4060 : 2001 | Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser |
| ASTM D 4287 : 2000 : R2010 | Standard Test Method for High-Shear Viscosity Using a Cone/Plate Viscometer |
| ASTM D 3450 : 2015 | Standard Test Method for Washability Properties of Interior Architectural Coatings |
| ASTM D 2369 : 2020 | Standard Test Method for Volatile Content of Coatings |
| ASTM D 6736 : 2008 | Standard Test Method for Burnish Resistance of Latex Paints |
| ASTM D 6900 : 2010 | Standard Test Method for Wet Adhesion of Latex Paints to a Gloss Alkyd Enamel Substrate |
| ASTM D 4707 : 1997 | Standard Test Method for Measuring Paint Spatter Resistance During Roller Application |
| ASTM E 84 : 2020 | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM D 1475 : 1960 : R1968 | Standard Method Of Test For Density Of Paint, Varnish, Lacquer, And Related Products |
| ASTM D 7306 : 2007 : R2013 | Standard Practice for Testing Low Temperature Film-Formation of Latex Paints by Visual Observation |
| ASTM D 3273 : 2021 | Standard Test Method for Resistance to Growth of Mold on the Surface of Interior Coatings in an Environmental Chamber |
| ASTM D 2196 : 2018 | Standard Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational Viscountess |
| ASTM D 1849 : 1995 | Standard Test Method for Package Stability of Paint |
| ASTM D 4707 : 2009 : R2017 | Standard Test Method for Measuring Paint Spatter Resistance During Roller Application |
| ASTM D 2244 : 2014 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM E 84 : 2021 : REV A | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM E 1347 : 2006 | Standard Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry |
| ASTM D 4541 : 2017 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 2805 : 1996 : REV A | Standard Test Method for Hiding Power of Paints by Reflectometry |
| ASTM D 1729 : 1996 : R2003 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM D 3793 : 2006 | Standard Test Method for Low-Temperature Coalescence of Latex Paint Films by Porosity Measurement (Withdrawn 2012) |
| ASTM D 4828 : 1994 : R2012 : EDT 1 | Standard Test Methods for Practical Washability of Organic Coatings |
| ASTM D 1210 : 2005 : R2014 | Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type Gage |
| ASTM D 4541 : 2022 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 1308 : 2002 : EDT 1 | Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes |
| ASTM D 4287 : 2000 : R2014 | Standard Test Method for High-Shear Viscosity Using a Cone/Plate Viscometer |
| ASTM D 2794 : 1993 : R1999 : EDT 1 | Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact) |
| ASTM D 1849 : 1995 : R2003 | Standard Test Method for Package Stability of Paint |
| ASTM D 2244 : 2005 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 4958 : 2010 | Standard Test Method for Comparison of the Brush Drag of Latex Paints |
| ASTM D 4287 : 2000 : R2019 | Standard Test Method for High-Shear Viscosity Using a Cone/Plate Viscometer |
| ASTM D 2369 : 2007 | Standard Test Method for Volatile Content of Coatings |
| ASTM D 4287 : 2000 : R2005 | Standard Test Method for High-Shear Viscosity Using a Cone/Plate Viscometer |
| ASTM D 1212 : 1991 : R2001 | Standard Test Methods for Measurement of Wet Film Thickness of Organic Coatings |
| ASTM D 1849 : 1995 : R2019 | Standard Test Method for Package Stability of Paint |
| ASTM D 1475 : 1998 : R2008 | Standard Test Method For Density of Liquid Coatings, Inks, and Related Products |
| ASTM D 2369 : 2010 : EDT 1 | Standard Test Method for Volatile Content of Coatings |
| ASTM D 1005 : 1995 : R2013 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
| ASTM D 3928 : 2000 : REV A : R2010 | Standard Test Method for Evaluation of Gloss or Sheen Uniformity |
| ASTM D 2794 : 1993 : R2004 | Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact) |
| ASTM D 1849 : 1995 : R2008 | Standard Test Method for Package Stability of Paint |
| ASTM D 1210 : 2005 : R2010 | Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type Gage |
| ASTM D 1308 : 1979 : R1981 : EDT 1 | Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes |
| ASTM D 1296 : 1993 : R1996 | Standard Test Method for Odor of Volatile Solvents and Diluents |
| ASTM D 3450 : 2000 | Standard Test Method for Washability Properties of Interior Architectural Coatings |
| ASTM D 2247 : 2015 : R2020 | Standard Practice for Testing Water Resistance of Coatings in 100 % Relative Humidity |
| ASTM D 2369 : 1993 | Standard Test Method for Volatile Content of Coatings |
| ASTM D 1212 : 1991 : R1996 : EDT 1 | Standard Test Methods for Measurement of Wet Film Thickness of Organic Coatings |
| ASTM D 5326 : 1994 : REV A : R2013 | Standard Test Method for Color Development in Tinted Latex Paints |
| ASTM D 6900 : 2003 | Standard Test Method for Wet Adhesion of Latex Paints to a Gloss Alkyd Enamel Substrate |
| ASTM D 5326 : 2022 | Standard Test Method for Color Development in Tinted Latex Paints |
| ASTM D 3273 : 2000 | Standard Test Method for Resistance to Growth of Mold on the Surface of Interior Coatings in an Environmental Chamber |
| ASTM D 3925 : 2002 : R2022 | Standard Practice for Sampling Liquid Paints and Related Pigmented Coatings |
| ASTM D 7786 : 2012 | Standard Test Method for Determining Enamel Holdout |
| ASTM D 2486 : 2006 : R2016 | Standard Test Methods for Scrub Resistance of Wall Paints |
| ASTM D 4585 : 2007 | Standard Practice for Testing Water Resistance of Coatings Using Controlled Condensation |
| ASTM D 4213 : 1996 : EDT 1 | Standard Test Method for Scrub Resistance of Paints by Abrasion Weight Loss |
| ASTM D 4958 : 2010 : R2016 | Standard Test Method for Comparison of the Brush Drag of Latex Paints |
| ASTM D 4707 : 2009 | Standard Test Method for Measuring Paint Spatter Resistance During Roller Application |
| ASTM D 2244 : 2007 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 4958 : 1997 | Standard Test Method for Comparison of the Brush Drag of Latex Paints |
| ASTM D 7786 : 2013 : R2019 | Standard Test Method for Determining Enamel Holdout |
| ASTM D 2244 : 2022 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 1308 : 1987 : R1998 | Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes |
| ASTM D 93 : 2000 | Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester |
| ASTM D 5150 : 1992 : R2003 | Standard Test Method for Hiding Power of Architectural Paints Applied by Roller |
| ASTM E 1347 : 2006 : R2011 | Standard Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry |
| ASTM D 5326 : 1994 : REV A | Standard Test Method for Color Development in Tinted Latex Paints |
| ASTM D 1296 : 2001 : R2007 | Standard Test Method for Odor of Volatile Solvents and Diluents |
| ASTM D 4400 : 2018 | Standard Test Method for Sag Resistance of Paints Using a Multinotch Applicator |
| ASTM E 313 : 1998 | Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates |
| ASTM E 105 : 2016 | Standard Practice for Probability Sampling of Materials |
| ASTM D 1729 : 1996 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM D 4287 : 2000 | Standard Test Method for High-Shear Viscosity Using a Cone/Plate Viscometer |
| ASTM D 7514 : 2009 | Standard Test Method for Evaluating Ink Stainblocking of Architectural Paint Systems by Visual Assessment |
| ASTM D 1212 : 1991 : R2007 | Standard Test Methods for Measurement of Wet Film Thickness of Organic Coatings |
| ASTM D 2805 : 2011 | Standard Test Method for Hiding Power of Paints by Reflectometry |
| ASTM D 1211 : 1997 | Standard Test Method for Temperature-Change Resistance of Clear Nitrocellulose Lacquer Films Applied to Wood (Withdrawn 2006) |
| ASTM D 4060 : 1995 | Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser |
| ASTM D 93 : 1985 | Standard Test Method for Flash Point by Pensky-Martens Closed Tester |
| ASTM D 6736 : 2008 : R2019 | Standard Test Method for Burnish Resistance of Latex Paints |
| ASTM D 4400 : 1999 : R2012 : EDT 1 | Standard Test Method for Sag Resistance of Paints Using a Multinotch Applicator |
| ASTM D 1729 : 2022 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM D 3450 : 2000 : R2010 : EDT 1 | Standard Test Method for Washability Properties of Interior Architectural Coatings |
| ASTM D 3450 : 2000 : R2005 | Standard Test Method for Washability Properties of Interior Architectural Coatings |
| ASTM D 3928 : 2000 : REV A : R2005 | Standard Test Method for Evaluation of Gloss or Sheen Uniformity |
| ASTM D 4828 : 1994 : R1999 | Standard Test Methods for Practical Washability of Organic Coatings |
| ASTM D 4400 : 1999 | Standard Test Method for Sag Resistance of Paints Using a Multinotch Applicator |
| ASTM D 2369 : 1995 | Standard Test Method for Volatile Content of Coatings |
| ASTM D 1005 : 1995 : R2007 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
| ASTM D 2369 : 2004 | Standard Test Method for Volatile Content of Coatings |
| ASTM D 4287 : 1994 | Standard Test Method for High-Shear Viscosity Using a Cone/Plate Viscometer |
| ASTM D 1849 : 1995 : R2014 : EDT 1 | Standard Test Method for Package Stability of Paint |
| ASTM D 2794 : 1993 : R2019 | Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact) |
| ASTM D 1308 : 2002 : R2007 | Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes |
| ASTM D 7488 : 2011 | Standard Test Method for Open Time of Latex Paints |
| ASTM D 2369 : 1990 | Standard Test Method for Volatile Content of Coatings |
| ASTM D 2196 : 2018 : EDT 1 | Standard Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational Viscometer |
| ASTM D 3925 : 2002 | Standard Practice for Sampling Liquid Paints and Related Pigmented Coatings |
| ASTM D 2244 : 2009 : REV A | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 5326 : 1994 : REV A : R2002 | Standard Test Method for Color Development in Tinted Latex Paints |
| ASTM D 3928 : 1989 | Standard Test Method for Evaluation of Gloss or Sheen Uniformity |
| ASTM D 3273 : 2016 | Standard Test Method for Resistance to Growth of Mold on the Surface of Interior Coatings in an Environmental Chamber |
| ASTM D 1212 : 1991 | Standard Test Methods for Measurement of Wet Film Thickness of Organic Coatings |
| ASTM D 2369 : 2003 | Standard Test Method for Volatile Content of Coatings |
| ASTM D 2244 : 1993 : R2000 | Standard Test Method for Calculation of Color Differences From Instrumentally Measured Color Coordinates |
| ASTM D 4541 : 1995 : EDT 1 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 4062 : 2011 | Standard Test Method for Leveling of Paints by Draw-Down Method |
| ASTM D 2247 : 1968 : R1973 | Standard Method for Testing Coated Metal Specimens At 100% Relative Humidity |
| ASTM D 7514 : 2014 | Standard Test Method for Evaluating Ink Stainblocking of Architectural Paint Systems by Visual Assessment |
| ASTM D 2486 : 2000 | Standard Test Methods for Scrub Resistance of Wall Paints |
| ASTM D 2794 : 1993 : R2010 | Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact) |
| ASTM D 1475 : 1998 | Standard Test Method for Density of Liquid Coatings, Inks, and Related Products |
| ASTM D 2369 : 2010 : R2015 : EDT 1 | Standard Test Method for Volatile Content of Coatings |
| ASTM D 3278 : 1996 : R2004 : EDT 1 | Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus |
| ASTM D 2805 : 1996 : REV A : R2003 | Standard Test Method for Hiding Power of Paints by Reflectometry |
| ASTM D 2196 : 1999 | Standard Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational (Brookfield type) Viscometer |
| ASTM D 4213 : 2008 : R2012 | Standard Test Method for Scrub Resistance of Paints by Abrasion Weight Loss |
| ASTM D 93 : 1997 | Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester |
| ASTM D 2369 : 1987 | Standard Test Method for Volatile Content of Coatings |
| ASTM D 3925 : 2002 : R2015 | Standard Practice for Sampling Liquid Paints and Related Pigmented Coatings |
| ASTM D 1005 : 1995 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
| ASTM D 2247 : 1999 | Standard Practice for Testing Water Resistance of Coatings in 100% Relative Humidity |
| ASTM D 7488 : 2011 : R2016 | Standard Test Method for Open Time of Latex Paints |
| ASTM D 4707 : 2009 : R2013 | Standard Test Method for Measuring Paint Spatter Resistance During Roller Application |
| ASTM D 4060 : 2014 | Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser |
| ASTM D 7489 : 2009 : R2013 | Standard Practice for Evaluating Touch-Up Properties of Architectural Coatings under Various Environmental Conditions |
| ASTM D 4060 : 2010 | Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser |
| ASTM D 2369 : 2001 : EDT 1 | Standard Test Method for Volatile Content of Coatings |
| ASTM D 2486 : 2006 : R2012 : EDT 1 | Standard Test Methods for Scrub Resistance of Wall Paints |
| ASTM D 3928 : 2000 : REV A | Standard Test Method for Evaluation of Gloss or Sheen Uniformity |
| ASTM D 4213 : 1996 : R2003 | Standard Test Method for Scrub Resistance of Paints by Abrasion Weight Loss |
| ASTM D 2369 : 1992 | Standard Test Method for Volatile Content of Coatings |
| ASTM D 1308 : 2002 | Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes |
| ASTM D 4060 : 2019 | Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser |
| ASTM D 3925 : 2002 : R2010 | Standard Practice for Sampling Liquid Paints and Related Pigmented Coatings |
| ASTM D 3278 : 1996 : R2011 | Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus (Withdrawn 2020) |
| ASTM D 3793 : 2000 | Standard Test Method for Low-Temperature Coalescence of Latex Paint Films |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.