ASTM D 3841 : 2021
Current
The latest, up-to-date edition.
Standard Specification for Glass-Fiber-Reinforced Polyester Plastic Panels
Hardcopy , PDF
English
19-05-2021
Committee |
D 20
|
DocumentType |
Standard
|
Pages |
6
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This specification covers the classification, materials of construction, workmanship, minimum physical requirements, and methods of testing glass-fiber reinforced polyester plastic panels intended for use in construction. Panels for specialized or unique applications have the potential to require values significantly above or below those stated in this specification. Recommended practices for certain specific applications are included as Appendix X1. This specification is not intended to restrict or limit technological changes affecting performance when those changes are agreed upon between the purchaser and the seller.
1.2Supplementary information on chemical resistance, resistance to heat, and installation practices are provided in Appendix X1.
1.3The classification of these plastic panels into types based on relative response to a laboratory test shall not be considered a fire hazard classification.
1.4The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.5The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in Tables and Figures) shall not be considered as requirements of this standard.
1.6Fire properties are determined by using laboratory flammability tests (Test Methods D635, D1929, and E84).
1.6.1This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions.
1.6.2Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.
1.7The following precautionary caveat pertains only to the test method portion, Section 8 of this specification. This specification does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this specification to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1:There is no known ISO equivalent to this standard.
1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 4364 : 2013 | Standard Practice for Performing Outdoor Accelerated Weathering Tests of Plastics Using Concentrated Sunlight |
ASTM D 635 : 2018 | Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position |
ASTM D 883 : 2023 | Standard Terminology Relating to Plastics |
ASTM D 696 : 2024 | Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and +30°C with a Vitreous Silica Dilatometer |
ASTM E 84 : 2023 : REV D | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 1494 : 2022 | Standard Test Method for Diffuse Light Transmission Factor of Reinforced Plastics Panels |
ASTM D 883 : 2024 : REV A | Standard Terminology Relating to Plastics |
ASTM E 831 : 2019 | Standard Test Method for Linear Thermal Expansion of Solid Materials by Thermomechanical Analysis |
ASTM E 84 : 2023 : REV C | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 883 : 2024 | Standard Terminology Relating to Plastics |
ASTM E 831 : 2024 | Standard Test Method for Linear Thermal Expansion of Solid Materials by Thermomechanical Analysis |
ASTM D 696 : 2016 | Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer |
ASTM D 883 : 2022 | Standard Terminology Relating to Plastics |
ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
ASTM E 84 : 2023 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM E 84 : 2021 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM E 84 : 2022 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 1929 : 2020 | Standard Test Method for Determining Ignition Temperature of Plastics |
ASTM D 635 : 2022 | Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position |
ASTM E 84 : 2024 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 1929 : 2023 | Standard Test Method for Determining Ignition Temperature of Plastics |
ASTM E 631 : 2015 : R2024 | Standard Terminology of Building Constructions |
ASTM E 84 : 2021 : REV A | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM G 155 : 2021 | Standard Practice for Operating Xenon Arc Lamp Apparatus for Exposure of Materials |
ASTM E 1175 : 1987 : R2022 | Standard Test Method for Determining Solar or Photopic Reflectance, Transmittance, and Absorptance of Materials Using a Large Diameter Integrating Sphere |
ASTM D 638 : 2014 | Standard Test Method for Tensile Properties of Plastics |
ASTM E 72 : 2015 | Standard Test Methods of Conducting Strength Tests of Panels for Building Construction |
ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
ASTM E 631 : 2015 | Standard Terminology of Building Constructions |
ASTM D 1494 : 2017 | Standard Test Method for Diffuse Light Transmission Factor of Reinforced Plastics Panels |
ASTM E 84 : 2023 : REV B | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM G 155 : 2013 | Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials |
ASTM E 1175 : 1987 : R2015 | Standard Test Method for Determining Solar or Photopic Reflectance, Transmittance, and Absorptance of Materials Using a Large Diameter Integrating Sphere |
ASTM D 570 : 2022 | Standard Test Method for Water Absorption of Plastics |
ASTM E 1084 : 1986 : R2023 | Standard Test Method for Solar Transmittance (Terrestrial) of Sheet Materials Using Sunlight |
ASTM E 72 : 2022 | Standard Test Methods of Conducting Strength Tests of Panels for Building Construction |
ASTM E 84 : 2023 : REV A | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM E 1084 : 1986 : R2015 | Standard Test Method for Solar Transmittance (Terrestrial) of Sheet Materials Using Sunlight |
ASTM D 570 : 1998 : R2018 | Standard Test Method for Water Absorption of Plastics |
ASTM D 4364 : 2013 : R2022 : EDT 1 | Standard Practice for Performing Outdoor Accelerated Weathering Tests of Plastics Using Concentrated Sunlight |
ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
ASTM E 972 : 1996 : R2021 | Standard Test Method for Solar Photometric Transmittance of Sheet Materials Using Sunlight |
ASTM D 638 : 2022 | Standard Test Method for Tensile Properties of Plastics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.