ASTM D 3983 : 1998
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Measuring Strength and Shear Modulus of Nonrigid Adhesives by the Thick-Adherend Tensile-Lap Specimen
Hardcopy , PDF
11-11-2014
English
10-03-1998
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 15.06, 2015 Defines a method of measuring the shear modulus and rupture stress in shear of adhesives in bonded joints.
| Committee |
D 14
|
| DocumentType |
Test Method
|
| Pages |
11
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1 This test method describes a method of measuring the shear modulus and rupture stress in shear of adhesives in bonded joints. The method employs lap-shear specimens with wood, metal, or composite adherends, with adhesives having shear moduli ranging up to 700 MPa (100000 psi). This test method is suitable generally for joints in which the ratio of adherend tensile modulus to adhesive shear modulus is greater than 300 to 1. It is not suitable for adhesives that have a high shear modulus in the cured state and that also require elimination of volatile constituents during cure.
1.2 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| MIL-A-85705 Revision A:1987 | ADHESIVE, AIRCRAFT, FOR STRUCTURAL REPAIR |
| ASTM D 6465 : 1999 : R2012 | Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants |
| AWS WHB.3.9 : 2007 | WELDING PROCESSES - PART 2: WELDING HANDBOOK, 9TH EDITION, VOL. 3 |
| ASTM D 6465 : 1999 | Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants |
| ASTM D 4896 : 2001 : R2008 : EDT 1 | Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results |
| ASTM D 6465 : 1999 : R2005 | Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants |
| DEFSTAN 00-970(PT1)SEC4/8(2011) : 2011 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 1: FIXED WING - SECTION 4 - DESIGN AND CONSTRUCTION |
| DEFSTAN 00-970(PT7)SEC2/2(2007) : 2007 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 7: ROTORCRAFT - SECTION 2: STRUCTURAL STRENGTH AND DESIGN FOR FLIGHT |
| DEFSTAN 00-970(PT0)/17(2016) : 2016 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT7)SEC2/3(2010) : 2010 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 7: ROTORCRAFT - SECTION 2: STRUCTURAL STRENGTH AND DESIGN FOR FLIGHT |
| DEFSTAN 00-970(PT1)SEC4/7(2011) : 2011 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 1: FIXED WING - SECTION 4: DESIGN AND CONSTRUCTION |
| DEFSTAN 00-970(PT1)SEC4/9(2012) : 2012 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 1: FIXED WING - SECTION 4 - DESIGN AND CONSTRUCTION |
| DEFSTAN 00-970(PT7)SEC2/SUPP4/5(2015) : INTERIM | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 7: ROTORCRAFT - SUPPLEMENT 4: DESIGN AND CONSTRUCTION (SUBPART D) |
| DEFSTAN 00-970(PT7)SEC4/2(2007) : 2007 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 7: ROTORCRAFT - SECTION 4: DETAIL DESIGN AND STRENGTH OF MATERIALS |
| DEFSTAN 00-970(PT1)SEC4/5(2007) : 2007 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 1: COMBAT AIRCRAFT - SECTION 4: DESIGN AND CONSTRUCTION |
| DEFSTAN 00-970(PT0)/15(2015) : 2015 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT7)SEC4/1(2006) : 2006 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 7: ROTORCRAFT - SECTION 4: DETAIL DESIGN AND STRENGTH OF MATERIALS |
| DEFSTAN 00-970(PT1)SEC4/11(2013) : 2013 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 1: FIXED WING - SECTION 4: DESIGN AND CONSTRUCTION |
| DEFSTAN 00-970(PT1)SEC4/10(2013) : 2013 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 1: FIXED WING - SECTION 4: DESIGN AND CONSTRUCTION |
| DEFSTAN 00-970(PT1)SEC4/4(2006) : 2006 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 1: COMBAT A/C - SECTION 4: DESIGN AND CONSTRUCTION |
| DEFSTAN 00-970(PT1)SEC4/12(2014) : 2014 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 1: FIXED WING - SECTION 4: DESIGN AND CONSTRUCTION |
| DEFSTAN 00-970(PT1)SEC4/6(2010) : 2010 | DESIGN AND AIRWORTHINESS REQUIREMENTS FORD SERVICE AIRCRAFT - PART 1: FIXED WING - SECTION 4: DESIGN AND CONSTRUCTION |
| DEFSTAN 00-970(PT1)SEC4/13(2015) : 2015 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 1: FIXED WING - SECTION 4: DESIGN AND CONSTRUCTION |
| DEFSTAN 00-970(PT0)/16(2015) : 2015 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| ASTM D 4896 : 2001 : R2016 | Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results |
| ASTM D 5574 : 1994 : R1999 : EDT 1 | Standard Test Methods for Establishing Allowable Mechanical Properties of Wood-Bonding Adhesives for Design of Structural Joints |
| ASTM D 5574 : 1994 : R2012 | Standard Test Methods for Establishing Allowable Mechanical Properties of Wood-Bonding Adhesives for Design of Structural Joints |
| ASME PCC-2:2022 | Repair of Pressure Equipment and Piping |
| DEFSTAN 00-970(PT7)SEC2/SUPPD/4(2014) : INTERIM | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 7: ROTORCRAFT - SUPPLEMENT D: DESIGN AND CONSTRUCTION (SUBPART D) |
| DEFSTAN 00-970(PT1)SEC4/14(2015) : 2015 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 1: FIXED WING - SECTION 4: DESIGN AND CONSTRUCTION |
| DEFSTAN 00-970(PT7)SEC2/SUPP4/6(2015) : 2015 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 7: ROTORCRAFT - SUPPLEMENT 4: DESIGN AND CONSTRUCTION (SUBPART D) |
| ASTM D 5574 : 1994 : R2005 | Standard Test Methods for Establishing Allowable Mechanical Properties of Wood-Bonding Adhesives for Design of Structural Joints |
| ASTM D 907 : 2015 : REDLINE | Standard Terminology of Adhesives |
| ASTM D 907 : 2015 | Standard Terminology of Adhesives |
| ASTM D 6465 : 1999 : R2016 | Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants |
| ASTM D 4896 : 2001 | Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results |
| ASTM D 143 : 2014 : REDLINE | Standard Test Methods for Small Clear Specimens of Timber |
| ASTM E 83 : 2016 : REDLINE | Standard Practice for Verification and Classification of Extensometer Systems |
| ASTM D 907 : 2015 : REDLINE | Standard Terminology of Adhesives |
| ASTM E 229 : 1997 | Standard Test Method for Shear Strength and Shear Modulus of Structural Adhesives (Withdrawn 2003) |
| ASTM D 905 : 2008 | Standard Test Method for Strength Properties of Adhesive Bonds in Shear by Compression Loading |
| ASTM E 104 : 2002 | Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Solutions |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.