![header thumbnail](/images/publishers\astm_cover.gif)
ASTM D 4000 : 2000
NA
Status of Standard is Unknown
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Classification System for Specifying Plastic Materials
Hardcopy , PDF
English
10-12-2001
Committee |
D 20
|
DocumentType |
Standard
|
Pages |
18
|
PublisherName |
American Society for Testing and Materials
|
Status |
NA
|
SupersededBy |
1.1 This standard provides a classification system for tabulating the properties of unfilled, filled, and reinforced plastic materials suitable for processing into parts.
Note 1—The classification system may serve many of the needs of industries using plastic materials. The standard is subject to revision as the need requires; therefore, the latest revision should always be used.
1.2 The classification system and subsequent line callout (specification) is intended to be a means of identifying plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection should be made by those having expertise in the plastics field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the inherent properties of the material not covered in this document, and the economic factors.
1.3 This classification system is based on the premise that plastic materials can be arranged into broad generic families using basic properties to arrange the materials into groups, classes, and grades. A system is thus established which, together with values describing additional requirements, permits as complete a description as desired of the selected material.
1.4 In all cases where the provisions of this classification system would conflict with the referenced ASTM specification for a particular material, the latter shall take precedence.
Note 2—When using this classification system the two-letter, three-digit suffix system applies.Note 3—When a material is used to fabricate a part where the requirements are too specific for a broad material callout, it is advisable for the user to consult the supplier to secure callout of the properties to suit the actual conditions to which the part is to be subjected.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D 790 : 2017 | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
ASTM D 3965 : 2016 | Standard Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings |
ASTM D 5026 : 2015 | Standard Test Method for Plastics: Dynamic Mechanical Properties: In Tension |
ASTM D 6778 : 2014 | Standard Classification System and Basis for Specification for Polyoxymethylene Molding and Extrusion Materials (POM) |
ASTM D 4440 : 2015 | Standard Test Method for Plastics: Dynamic Mechanical Properties Melt Rheology |
ASTM D 6779 : 2017 | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 1238 : 2013 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 5336 : 2015 : REV A | Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Material |
ASTM D 8069 : 2017 : REV A | Standard Test Method for Determining Flexural Modulus of Full Section Pultruded Fiber Reinforced Polymer (FRP) Composite Members with Doubly Symmetric Cross Sections under Bending |
ASTM D 2990 : 2017 | Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics |
ASTM D 4549 : 2015 | Standard Classification System and Basis for Specification for Polystyrene and Rubber-Modified Polystyrene Molding and Extrusion Materials (PS) |
ASTM D 638 : 2014 | Standard Test Method for Tensile Properties of Plastics |
ASTM D 4634 : 2016 | Standard Classification System and Basis for Specification for Styrene-Maleic Anhydride Molding and Extrusion Materials (S/MA) |
ASTM D 5927 : 2017 | Standard Classification System for and Basis for Specifications for Thermoplastic Polyester (TPES) Injection and Extrusion Materials Based on ISO Test Methods |
ASTM D 7192 : 2018 | Standard Test Method for High Speed Puncture Properties of Plastic Films Using Load and Displacement Sensors |
ASTM D 695 : 2015 | Standard Test Method for Compressive Properties of Rigid Plastics |
ASTM D 6112 : 2018 | Standard Test Methods for Compressive and Flexural Creep and Creep-Rupture of Plastic Lumber and Shapes |
ASTM D 5024 : 2015 | Standard Test Method for Plastics: Dynamic Mechanical Properties: In Compression |
ASTM D 6835 : 2017 | Standard Classification System for Thermoplastic Elastomer-Ether-Ester Molding and Extrusion Materials (TEEE) |
ASTM F 2026 : 2017 | Standard Specification for Polyetheretherketone (PEEK) Polymers for Surgical Implant Applications |
ASTM D 1043 : 2016 | Standard Test Method for Stiffness Properties of Plastics as a Function of Temperature by Means of a Torsion Test |
ASTM D 5045 : 2014 | Standard Test Methods for Plane-Strain Fracture Toughness and Strain Energy Release Rate of Plastic Materials |
ASTM D 6098 : 2016 | Standard Classification System and Basis for Specification for Extruded and Compression Molded Shapes Made from Polycarbonate (PC) |
ASTM D 7031 : 2011 : R2019 | Standard Guide for Evaluating Mechanical and Physical Properties of Wood-Plastic Composite Products |
ASTM D 5083 : 2017 | Standard Test Method for Tensile Properties of Reinforced Thermosetting Plastics Using Straight-Sided Specimens |
ASTM D 706 : 2015 | Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds (CA) |
ASTM D 6339 : 2011 : R2019 | Standard Classification System for and Basis for Specifications for Syndiotactic Polystyrene Molding and Extrusion (SPS) |
ASTM D 6865 : 2017 | Standard Classification System and Basis for Specifications for Acrylonitrile–Styrene–Acrylate (ASA) and Acrylonitrile–EPDM–Styrene (AES) Plastics and Alloys Molding and Extrusion Materials |
ASTM D 5628 : 2018 | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass) |
ASTM D 4093 : 1995 : R2014 | Standard Test Method for Photoelastic Measurements of Birefringence and Residual Strains in Transparent or Translucent Plastic Materials |
ASTM D 2582 : 2016 | Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting |
ASTM F 3091/F3091M : 2014 | Standard Specification for Powder Bed Fusion of Plastic Materials |
ASTM D 4065 : 2012 | Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures |
ASTM D 1938 : 2019 | Standard Test Method for Tear-Propagation Resistance (Trouser Tear) of Plastic Film and Thin Sheeting by a Single-Tear Method |
ASTM D 1562 : 2015 | Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds (CAP) |
ASTM D 6693/D6693M : 2004 : R2015 : EDT 1 | Standard Test Method for Determining Tensile Properties of Nonreinforced Polyethylene and Nonreinforced Flexible Polypropylene Geomembranes |
ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
ASTM D 1004 : 2013 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting |
ASTM D 3763 : 2018 | Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors |
ASTM F 1499 : 2017 | Standard Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV) |
ASTM D 6272 : 2017 | Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending |
ASTM D 5740 : 2018 | Standard Guide for Writing Material Standards in the Classification D4000 Format |
ASTM D 6713 : 2014 | Standard Specification for Extruded and Compression Molded Shapes Made from Poly(Vinylidene Fluoride) (PVDF) |
ASTM D 4673 : 2016 | Standard Classification System for and Basis for Specification for Acrylonitrile–Butadiene–Styrene (ABS) Plastics and Alloys Molding and Extrusion Materials |
ASTM F 561 : 2019 | Standard Practice for Retrieval and Analysis of Medical Devices, and Associated Tissues and Fluids |
ASTM D 7032 : 2017 | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite and Plastic Lumber Deck Boards, Stair Treads, Guards, and Handrails |
ASTM D 7292 : 2018 | Standard Specification for Extruded, Compression-Molded, and Injection-Molded Basic Shapes of Polyamide-Imide (PAI) |
ASTM D 5023 : 2015 | Standard Test Method for Plastics: Dynamic Mechanical Properties: In Flexure (Three-Point Bending) |
ASTM D 952 : 2015 | Standard Test Method for Bond or Cohesive Strength of Sheet Plastics and Electrical Insulating Materials |
ASTM D 5857 : 2017 | Standard Specification for Polypropylene Injection and Extrusion Materials Using ISO Protocol and Methodology |
ASTM D 7436 : 2017 | Standard Classification System for Unfilled Polyethylene Plastics Molding and Extrusion Materials with a Fractional Melt Index Using ISO Protocol and Methodology |
ASTM D 1822 : 2013 | Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials |
ASTM D 2673 : 2014 | Standard Specification for Oriented Polypropylene Film |
ASTM D 732 : 2017 | Standard Test Method for Shear Strength of Plastics by Punch Tool |
ASTM D 4203 : 2017 | Standard Specification for and Basis for Specifications for Styrene-Acrylonitrile (SAN) Injection and Extrusion Materials |
ASTM D 6712 : 2017 | Standard Specification for Ultra-High-Molecular-Weight Polyethylene (UHMW-PE) Solid Plastic Shapes |
ASTM D 1922 : 2015 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
ASTM D 4067 : 2016 | Standard Classification System and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods |
ASTM D 6338 : 2017 | Standard Classification System for Highly Crosslinked Thermoplastic Vulcanizates (HCTPV) Based on ASTM Standard Test Methods |
ASTM D 5138 : 2016 | Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP) |
ASTM D 7750 : 2012 : R2017 | Standard Test Method for Cure Behavior of Thermosetting Resins by Dynamic Mechanical Procedures using an Encapsulated Specimen Rheometer |
ASTM D 6262 : 2017 | Standard Specification for Extruded, Compression Molded, and Injection Molded Basic Shapes of Poly(aryl ether ketone) (PAEK) |
ASTM D 882 : 2018 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting |
ASTM F 2820 : 2012 | Standard Specification for Polyetherketoneketone (PEKK) Polymers for Surgical Implant Applications |
ASTM D 4066 : 2013 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
ASTM D 8033 : 2016 | Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials |
ASTM D 707 : 2015 | Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds (CAB) |
ASTM D 3935 : 2015 | Standard Classification System and Basis for Specification for Polycarbonate (PC) Unfilled and Reinforced Material |
ASTM D 7293 : 2012 | Standard Specification for Extruded and Compression-Molded Shapes Made from Polyetherimide (PEI) |
ASTM F 1488 : 2014 : R2019 | Standard Specification for Coextruded Composite Pipe |
ASTM D 2583 : 2013 : REV A | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor (Withdrawn 2022) |
ASTM D 1894 : 2014 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting (Withdrawn 2023) |
ASTM D 5205 : 2016 | Standard Classification System and Basis for Specification for Polyetherimide (PEI) Materials |
ASTM D 7474 : 2017 | Standard Practice for Determining Residual Stresses in Extruded or Molded Sulfone Plastic (SP) Parts by Immersion in Various Chemical Reagents |
ASTM D 788 : 2016 | Standard Classification System for Poly(Methyl Methacrylate) (PMMA) Molding and Extrusion Compounds |
ASTM D 6108 : 2019 | Standard Test Method for Compressive Properties of Plastic Lumber and Shapes |
ASTM D 785 : 2008 : R2015 | Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials |
ASTM D 6394 : 2014 | Standard Specification for Sulfone Plastics (SP) |
ASTM D 6261 : 2014 | Standard Specification for Extruded and Compression Molded Basic Shapes Made from Thermoplastic Polyester (TPES) |
ASTM D 4976 : 2012 : REV A | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
ASTM D 1044 : 2013 | Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion |
ASTM D 1204 : 2014 | Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature |
ASTM D 6358 : 2019 : EDT 1 | Standard Classification System and Basis for Specification for Poly (Phenylene Sulfide) (PPS) Injection Molding, Extrusion and Blow Molding Materials Using ISO Methods |
ASTM D 4101 : 2017 : EDT 1 | Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 6110 : 2018 | Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics |
ASTM D 2838 : 2018 | Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting |
ASTM D 5675 : 2013 : R2018 | Standard Classification for Low Molecular Weight PTFE and FEP Micronized Powders |
ASTM D 1708 : 2018 | Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.