ASTM D 4285 : 1983 : R2018
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Indicating Oil or Water in Compressed Air
Available format(s)
Hardcopy , PDF
Superseded date
18-07-2024
Superseded by
Language(s)
English
Published date
01-08-2018
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 06.02, 2017 Describes the presence of oil or water in compressed air used for abrasive blast cleaning, air blast cleaning, and coating application operations.
| Committee |
D 01
|
| DocumentType |
Test Method
|
| Pages |
2
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method is used to determine the presence of oil or water in compressed air used for abrasive blast cleaning, air blast cleaning, and coating application operations.
1.2The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 4.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| SSPC-SP 5 (WAB) : 2015 | WHITE METAL WET ABRASIVE BLAST CLEANING (SSPC-SP 5 (WAB)/NACE WAB-1) |
| NACE 10 : 2002 | FIBERGLASS-REINFORCED PLASTIC (FRP) LININGS APPLIED TO BOTTOMS OF CARBON STEEL ABOVEGROUND STORAGE TANKS |
| NACE RP 03 02 : 2002 | SELECTION AND APPLICATION OF A COATING SYSTEM TO INTERIOR SURFACES OF NEW AND USED RAIL TANK CARS IN MOLTEN SULFUR SERVICE |
| EN ISO 18797-1:2017 | Petroleum, petrochemical and natural gas industries - External corrosion protection of risers by coatings and linings - Part 1: Elastomeric coating systems-polychloroprene or EPDM (ISO 18797-1:2016) |
| SSPC-SP 7 (WAB) : 2015 | BRUSH-OFF WET ABRASIVE BLAST CLEANING (SSPC-SP 7 (WAB)/NACE WAB-4) |
| 15/30278562 DC : 0 | BS ISO 18797-1 - PETROLEUM, PETROCHEMICALS AND NATURAL GAS INDUSTRIES - EXTERNAL CORROSION PROTECTION OF RISERS BY COATINGS AND LININGS - PART 1: ELASTOMERIC COATING SYSTEMS - POLYCHLOROPRENE OR EPDM |
| AASHTO PP 79 : 2014 | PRACTICE FOR HIGH FRICTION SURFACE TREATMENT FOR ASPHALT AND CONCRETE PAVEMENTS |
| ASTM D 5107 : 2003 | Standard Practice for Preparatory Surface Cleaning of Architectural Sandstone |
| SSPC-SP 10 (WAB) : 2015 | NEAR-WHITE METAL WET ABRASIVE BLAST CLEANING (SSPC-SP 10 (WAB)/NACE WAB-2) |
| NACE 43114 : 2014 | NONVISIBLE CONTAMINANTS ON RAILCAR SURFACES |
| NACE SP 05 92 : 2006 | APPLICATION OF A COATING SYSTEM TO INTERIOR SURFACES OF NEW AND USED RAIL TANK CARS IN CONCENTRATED (90 TO 98%) SULFURIC ACID SERVICE |
| NACE RP 08 92 : 2001 | COATINGS AND LININGS OVER CONCRETE FOR CHEMICAL IMMERSION AND CONTAINMENT SERVICE |
| SSPC-SP 15 : 2012 | COMMERCIAL GRADE POWER-TOOL CLEANING |
| ASTM D 823 : 2018 | Standard Practices for Producing Films of Uniform Thickness of Paint, Coatings and Related Products on Test Panels |
| ASTM C 1147 : 2014 | Standard Practice for Determining the Short Term Tensile Weld Strength of Chemical-Resistant Thermoplastics |
| I.S. EN ISO 18797-1:2017 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - EXTERNAL CORROSION PROTECTION OF RISERS BY COATINGS AND LININGS - PART 1: ELASTOMERIC COATING SYSTEMS-POLYCHLOROPRENE OR EPDM (ISO 18797-1:2016) |
| NACE SP 08 15 : 2015 | COMMERCIAL WET ABRASIVE BLAST CLEANING (SSPC-SP 6 (WAB)/NACE WAB-3) |
| ASTM D 3089 : 1997 : R2008 | Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes |
| ASTM D 7396 : 2014 : REDLINE | Standard Guide for Preparation of New, Continuous Zinc-Coated (Galvanized) Steel Surfaces for Painting |
| ASTM D 4258 : 2005 : R2017 | Standard Practice for Surface Cleaning Concrete for Coating |
| ASTM D 4259 : 1988 : R2006 | Standard Practice for Abrading Concrete |
| NACE RP 01 76 : 2003 | CORROSION CONTROL OF STEEL FIXED OFFSHORE STRUCTURES ASSOCIATED WITH PETROLEUM PRODUCTION |
| NACE RP 02 88 : 2004 | INSPECTION OF LININGS ON STEEL AND CONCRETE |
| NACE RP 02 95 : 0 | APPLICATION OF A COATING SYSTEM TO INTERIOR SURFACES OF NEW AND USED RAIL TANK CARS |
| NACE SP 01 91 : 2017 | APPLICATION OF INTERNAL PLASTIC COATINGS FOR OILFIELD TUBULAR GOODS AND ACCESSORIES |
| ASTM D 7602 : 2011 : R2017 | Standard Practice for Installation of Vulcanized Rubber Linings |
| 14/30300605 DC : 0 | BS EN ISO 21809-3 - PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 3: FIELD JOINT COATINGS |
| SSPC-SP 11 : 2012 | POWER-TOOL CLEANING TO BARE METAL |
| BS ISO 18797-1 : 2016 COR 2017 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - EXTERNAL CORROSION PROTECTION OF RISERS BY COATINGS AND LININGS - PART 1: ELASTOMERIC COATING SYSTEMSPOLYCHLOROPRENE OR EPDM |
| NACE RP 03 86 : 2003 | APPLICATION OF A COATING SYSTEM TO INTERIOR SURFACES OF COVERED STEEL HOPPER RAIL CARS IN PLASTIC, FOOD, AND CHEMICAL SERVICE |
| 17/30313373 DC : 0 | BS ISO 21809-11 - PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 11: COATING REPAIRS ON REHABILITATION |
| ASTM D 5107 : 2003 : R2013 | Standard Practice for Preparatory Surface Cleaning of Architectural Sandstone |
| NACE RP 06 92 : 2003 | APPLICATION OF A COATING SYSTEM TO EXTERIOR SURFACES OF STEEL RAIL CARS |
| NACE SP 08 92 : 2007 | COATINGS AND LININGS OVER CONCRETE FOR CHEMICAL IMMERSION AND CONTAINMENT SERVICE |
| NACE 12/AWS C2.23M/SSPC CS- 23 : 2016 | SPECIFICATION FOR THE APPLICATION OF THERMAL SPRAY COATINGS (METALLIZING) OF ALUMINUM, ZINC, AND THEIR ALLOYS AND COMPOSITES FOR THE CORROSION PROTECTION OF STEEL |
| ASTM D 6237 : 2009 : R2015 | Standard Guide for Painting Inspectors (Concrete and Masonry Substrates) |
| ASTM D 4259 : 2018 | Standard Practice for Preparation of Concrete by Abrasion Prior to Coating Application |
| ASTM D 5498 : 2012 : REV A : R2018 | Standard Guide for Developing a Training Program for Personnel Performing Coating and Lining Work Inspection for Nuclear Facilities |
| ASTM D 6386 : 2016 : REV A | Standard Practice for Preparation of Zinc (Hot-Dip Galvanized) Coated Iron and Steel Product and Hardware Surfaces for Painting |
| ASTM D 3276 : 2015 : EDT 1 | Standard Guide for Painting Inspectors (Metal Substrates) |
| ASTM D 7055 : 2019 | Standard Practice for Preparation (by Abrasive Blast Cleaning) of Hot-Rolled Carbon Steel Panels for Testing of Coatings |
| ASTM D 7396 : 2014 | Standard Guide for Preparation of New, Continuous Zinc-Coated (Galvanized) Steel Surfaces for Painting |
| ASTM D 7803 : 2019 | Standard Practice for Preparation of Zinc (Hot-Dip Galvanized) Coated Iron and Steel Product and Hardware Surfaces for Powder Coating |
| ASTM D 4258 : 2005 : R2012 | Standard Practice for Surface Cleaning Concrete for Coating |
| ASTM D 7803 : 2012 | Standard Practice for Preparation of Zinc (Hot-Dip Galvanized) Coated Iron and Steel Product and Hardware Surfaces for Powder Coating |
| ASTM D 7602 : 2011 | Standard Practice for Installation of Vulcanized Rubber Linings |
| NACE SP 01 08 : 2008 | CORROSION CONTROL OF OFFSHORE STRUCTURES BY PROTECTIVE COATINGS |
| 07/30083514 DC : 0 | BS EN ISO 21809-3 - PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED AND SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 3: FIELD JOINT COATINGS |
| NACE SP 02 95 : 2008 | APPLICATION OF A COATING SYSTEM TO INTERIOR SURFACES OF NEW AND USED RAIL TANK CARS |
| AASHTO R 31 : 2009 : R2014 | PRACTICE FOR EVALUATION OF PROTECTIVE COATING SYSTEMS FOR STRUCTURAL STEEL |
| NACE SP 02 88:2011 | INSPECTION OF LINING APPLICATION IN STEEL AND CONCRETE EQUIPMENT |
| SSPC-SP 14 (WAB) : 2015 | INDUSTRIAL WET ABRASIVE BLAST CLEANING (SSPC-SP 14 (WAB)/NACE WAB-8) |
| SAE AS7489 | Standard Requirements for Aerospace Organic Coatings Applicator Certification |
| NACE 12 : 2003 | SPECIFICATION FOR THE APPLICATION OF THERMAL SPRAY COATINGS (METALLIZING) OF ALUMINUM, ZINC, AND THEIR ALLOYS AND COMPOSITES FOR THE CORROSION PROTECTION OF STEEL |
| BS EN ISO 18797-1:2017 | Petroleum, petrochemical and natural gas industries. External corrosion protection of risers by coatings and linings Elastomeric coating systems-polychloroprene or EPDM |
| ISO 18797-1:2016 | Petroleum, petrochemical and natural gas industries — External corrosion protection of risers by coatings and linings — Part 1: Elastomeric coating systems-polychloroprene or EPDM |
| ASTM C 811 : 1998 : R2008 | Standard Practice for Surface Preparation of Concrete for Application of Chemical-Resistant Resin Monolithic Surfacings (Withdrawn 2012) |
| ASTM C 1147 : 2014 : REDLINE | Standard Practice for Determining the Short Term Tensile Weld Strength of Chemical-Resistant Thermoplastics |
| ISO 21809-3:2016 | Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 3: Field joint coatings |
| NACE 11 : 2003 | THIN-FILM ORGANIC LININGS APPLIED IN NEW CARBON STEEL PROCESS VESSELS |
| NASA STD 5008 : 2011 | PROTECTIVE COATING OF CARBON STEEL, STAINLESS STEEL, AND ALUMINUM ON LAUNCH STRUCTURES, FACILITIES, AND GROUND SUPPORT EQUIPMENT |
| ASTM C 811 : 1998 : R2003 | Standard Practice for Surface Preparation of Concrete for Application of Chemical-Resistant Resin Monolithic Surfacings |
| I.S. EN ISO 21809-3:2016 | PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 3: FIELD JOINT COATINGS (ISO 21809-3:2016) |
| 16/30278559 DC : 0 | BS ISO 18796-1 - PETROLEUM, PETROCHEMICALS AND NATURAL GAS INDUSTRIES - INTERNAL COATING AND LINING OF CARBON STEEL PROCESS VESSELS - PART 1: TECHNICAL REQUIREMENTS |
| NACE SP 10 15 : 2015 | BRUSH-OFF WET ABRASIVE BLAST CLEANING (SSPC-SP 7 (WAB)/NACE WAB-4) |
| BS EN ISO 16961:2015 | Petroleum, petrochemical and natural gas industries. Internal coating and lining of steel storage tanks |
| BS EN ISO 21809-3:2016 | Petroleum and natural gas industries. External coatings for buried or submerged pipelines used in pipeline transportation systems Field joint coatings |
| SSPC-PA GUIDE 13 : 2006 | GUIDE SPECIFICATION FOR APPLICATION OF COATING SYSTEMS WITH ZINC-RICH PRIMERS TO STEEL BRIDGES |
| NACE RP 05 92 : 0 | APPLICATION OF A COATING SYSTEM TO INTERIOR SURFACES OF NEW AND USED RAIL TANK CARS IN CONCENTRATED (90 TO 98%) SULFURIC ACID SERVICE |
| SSPC-PA 15 : 2013 | MATERIAL AND PREPARATION REQUIREMENTS FOR STEEL TEST PANELS USED TO EVALUATE THE PERFORMANCE OF INDUSTRIAL COATINGS |
| API SPEC 16F : 2017 | SPECIFICATION FOR MARINE DRILLING RISER EQUIPMENT |
| NACE SP 03 98 : 2015 | RECOMMENDATIONS FOR TRAINING AND QUALIFYING PERSONNEL AS RAIL CAR COATING AND LINING INSPECTORS |
| NACE SP 06 15 : 2015 | NEAR-WHITE METAL WET ABRASIVE BLAST CLEANING (SSPC-SP 10 (WAB)/NACE WAB-2) |
| ASTM D 4259 : 1988 : R2012 | Standard Practice for Abrading Concrete |
| ASTM D 6237 : 2009 | Standard Guide for Painting Inspectors (Concrete and Masonry Substrates) |
| ASTM D 5161 : 2004 : REV A | Standard Guide for Specifying Inspection Requirements for Coating and Lining Work (Metal Substrates) (Withdrawn 2013) |
| ASTM D 5161 : 2004 | Standard Guide for Specifying Inspection Requirements for Coating and Lining Work (Metal Substrates) |
| SSPC-SP 6 (WAB) : 2015 | COMMERCIAL WET ABRASIVE BLAST CLEANING (SSPC-SP 6 (WAB)/NACE WAB-3) |
| ISO 16961:2015 | Petroleum, petrochemical and natural gas industries — Internal coating and lining of steel storage tanks |
| EN ISO 21809-3:2016 | Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 3: Field joint coatings (ISO 21809-3:2016) |
| EN ISO 16961:2015 | Petroleum, petrochemical and natural gas industries - Internal coating and lining of steel storage tanks (ISO 16961:2015) |
| ASTM D 4259 : 1988 : R1999 | Standard Practice for Abrading Concrete |
| NACE SP 07 15 : 2015 | WHITE METAL WET ABRASIVE BLAST CLEANING (SSPC-SP 5 (WAB)/NACE WAB-1) |
| AWS C2.23M/C2.23 : 2003 | SPECIFICATION FOR THE APPLICATION OF THERMAL SPRAY COATINGS (METALLIZING) OF ALUMINUM, ZINC, AND THEIR ALLOYS AND COMPOSITES FOR THE CORROSION PROTECTION OF STEEL |
| NACE SP 03 02 : 2007 | SELECTION AND APPLICATION OF A COATING SYSTEM TO INTERIOR SURFACES OF NEW AND USED RAIL TANK CARS IN MOLTEN SULFUR SERVICE |
| NACE SP 03 86 : 2007 | APPLICATION OF A COATING SYSTEM TO INTERIOR SURFACES OF COVERED STEEL HOPPER RAIL CARS IN PLASTIC, FOOD, AND CHEMICAL SERVICE |
| ASTM D 5107 : 2003 : R2007 | Standard Practice for Preparatory Surface Cleaning of Architectural Sandstone |
| NACE SP 09 15 : 2015 | INDUSTRIAL WET ABRASIVE BLAST CLEANING (SSPC-SP 14 (WAB)/NACE WAB-8) |
| AWS C2.16 : 1992 | GUIDE FOR THERMAL SPRAY OPERATOR QUALIFICATION |
| UNE-EN ISO 21809-3:2016 | Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 3: Field joint coatings (ISO 21809-3:2016) |
| I.S. EN ISO 16961:2015 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - INTERNAL COATING AND LINING OF STEEL STORAGE TANKS (ISO 16961:2015) |
| ASTM C 811 : 1998 | Standard Practice for Surface Preparation of Concrete for Application of Chemical-Resistant Resin Monolithic Surfacings |
| ASTM D 4258 : 2005 | Standard Practice for Surface Cleaning Concrete for Coating |
| PIP CTSL1000 : 2017 | APPLICATION OF INTERNAL LININGS |
| PIP CTSU1000 : 2018 | APPLICATION OF UNDERGROUND COATINGS |
| ASME RTP 1 : 2015 | REINFORCED THERMOSET PLASTIC CORROSION-RESISTANT EQUIPMENT |
| ASME RTP-1 : 2017 | REINFORCED THERMOSET PLASTIC CORROSION-RESISTANT EQUIPMENT |
| PIP CTSC1000 : 2017 | APPLICATION OF COATINGS TO CONCRETE |
| ASTM D 7055 : 2019 : R2024 | Standard Practice for Preparation (by Abrasive Blast Cleaning) of Hot-Rolled Carbon Steel Panels for Testing of Coatings |
| ASTM D 3276 : 2021 | Standard Guide for Painting Inspectors (Metal Substrates) |
| ASTM D 4258 : 2023 | Standard Practice for Surface Cleaning Concrete for Coating |
| ASTM D 6386 : 2022 | Standard Practice for Preparation of Zinc (Hot-Dip Galvanized) Coated Iron and Steel Product and Hardware Surfaces for Painting |
| ASTM D 5107 : 2003 : R2022 | Standard Practice for Preparatory Surface Cleaning of Architectural Sandstone |
| ASTM D 7396 : 2014 : R2020 | Standard Guide for Preparation of New, Continuous Zinc-Coated (Galvanized) Steel Surfaces for Painting |
| ASTM C 1147 : 2014 : R2022 | Standard Practice for Determining the Short Term Tensile Weld Strength of Chemical-Resistant Thermoplastics |
| ASTM C 704/C704M : 2015 : R2022 : EDT 1 | Standard Test Method for Abrasion Resistance of Refractory Materials at Room Temperature |
| ASTM D 6237 : 2019 | Standard Guide for Painting Inspectors (Concrete and Masonry Substrates) |
| ASTM D 823 : 2018 : R2022 | Standard Practices for Producing Films of Uniform Thickness of Paint, Coatings and Related Products on Test Panels |
| PIP RFSM2000 : 2005 | MONOLITHIC REFRACTORY INSTALLATION SPECIFICATION |
| SSPC-CS 23.00 : 2016 | SPECIFICATION FOR THE APPLICATION OF THERMAL SPRAY COATINGS (METALLIZING) OF ALUMINUM, ZINC, AND THEIR ALLOYS AND COMPOSITES FOR THE CORROSION PROTECTION OF STEEL |
| PIP CTSE1000 : 2012 | APPLICATION OF EXTERNAL COATINGS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.